Question about 1991 Mitsubishi Galant

1 Answer

What is the setting for ignition timing on a 2 litre, 4 cyl 1991 mitsi

Posted by on

  • mandmss Aug 03, 2009

    Thanks for that, a big help

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 167 Answers

5 degrees BTDC +/- 1 degree at 700 rpm.With Vacuum advance connected.
Hope that helps.

Posted on Aug 02, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Both coils do not fire on 1 and 4. Will start but only running on 2 cylinders. Could both coils be bad or should I look elsewhere?


Part 3 -How to Test the Ignition Module and Crank Sensor ...

easyautodiagnostics.com > Ford > 2.3L
Mar 1, 2012 - Spark plugs for cylinders #2 and #3 get spark at the exact same time. ...voltage -12 Volts) to both individual ignition coils within the coil pack. ... Ford Mustang or Ranger (or 2.3L Mazda B2300), this is what you'll need ... for this 'Switching Signal' at the coil pack... but you can also test this ... 1991, 1992, 1993.

How to Diagnose a Misfiring Cylinder (2.3L Ford Ranger ...

troubleshootmyvehicle.com > Ford > 2.3L
Apr 3, 2012 - Bad Fuel Injectors can cause a Misfire Condition. ... the ignition system on the 2.3L Ford Mustang or Ranger consists of 2 ignition coil packs, ...

2002 ranger misfire rough idle - Discussion on Topix

www.topix.com > Ford Ranger
Jul 27, 2007 - My truck is giving the code misfire in number 4 cyl. I replaced my spark plugs, Wires, Coil packs (both of them) and all my fuil ... three (3.0L v6) go bad, the fuel/air mixture gets messed up. Judged: 2. 2 ... My truck runs rough only at idle. ...code for ford ranger 2002, 2.3 5speed. truck runs like a champ but that ...

Extremely stumped! I need the best and brightest 1994 Ford ...

answers.edmunds.com > Edmunds Answers

Jan 31, 2016 | Cars & Trucks

1 Answer

Where can I get a diagram to set the timing on a 1991 ford ranger?


First What type of engine is it 6 cyl /Petrol/Diesel/or V8 carb/type
or F.Inj , they are all differant.

Oct 05, 2014 | 1991 Ford Ranger Supercab

1 Answer

Replaced Head On 91 4 cyl. capri. Cant get it to run now


How did you set the timing for both the ignition and the valves?

Aug 30, 2013 | 1991 Mercury Capri

2 Answers

Firing order


6 cyl 1-6-5-4-3-2

Jan 21, 2011 | 1986 Oldsmobile Ciera

1 Answer

Cannot figure out the firing order for my 1991 isuzu rodeo


Facing towards front of engine-number 1 is on passenger side front cyl of engine. Number 2 is front cyl on driver's side-number 3 middle cyl on passenger side-4 on middle cyl driver's side-5 on back cyl passenger side and 6 on back cyl driver's side. The distributer rotates COUNTER CLOCKWISE-number 1 cyl's sparkplug wire attaches to distributer cap connection closest to number 5 cyl.-to your right side of this plug wire on cap would go cyl number 2-then 3-then 4-then 5 and then 6. The firing order is:1,2,3,4,5,6

Apr 08, 2010 | 1991 Isuzu Rodeo

1 Answer

2006 dodge caravan, 6 cyl. relaced cole, sparkepugs and wires in oct. 2009. Engine is reading #2 cyl. misfire again. Why


Firts time swap spark plug & ignition coil between two different cylinders and read again if the same #2 cyl. misfires !
If #2 cyl. is OK and another cyl. misfires then spark plug or ignition coil is out of order and must be replaced.
If #2 cyl. misfires again then #2 injector must be checked !
If ignition coils & spark plugs (complete set for 6 cyl.) are replaced then you must check #2 injector !

Mar 15, 2010 | 2006 Dodge Caravan

1 Answer

Plug wire order on coil pack just put on a new one


My sincere apologies for the delayed response.
I am personally going back to answer your unanswered questions.
I have only been a free contributor to this site for the past 4-months.

I do not know if you still need this information, but I am going ahead and answering it anyway.


I do not know if you have the 2.5L (4-Cyl), 2.8L (6-Cyl), or the 3.8L (6-Cyl); however I have included all three below.

For the 2.5L (4-Cyl)
Firing Order:
1-3-4-2
Cylinders:
(back of engine)
1-----2-----3-----4
(front of engine)
Ignition Connections:
(back)
o <-----1
o <-----4
___
o <----2
o <----3
(front)

For the 2.8L (6-Cyl):
Firing Order:
1-2-3-4-5-6
Cylinders:
(back of engine)
1--------3--------5
2--------4--------6
(front of engine)
Ignition Connections:
.........(back)
|.1..4.|.|.6..3.|.|.2..5.|
.........(front)

For the 3.8L (6-Cyl):
Firing Order:
1-6-5-4-3-2
Cylinders:
(back of engine)
2------4-------6
1------3-------5
(front of engine)
Ignition Connections:
Type I:
(back)
6..2..4
3..5..1
(front)
Type II:
(back)
|.3..6.|.|.2..5.|.|.4..1.|
(front)

Let me know if this helped, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!

Again my apologies...





Jan 07, 2010 | 1988 Oldsmobile Cutlass Ciera

1 Answer

1991 honda accord - runs rough and stalls on start up.


Did you set the ignition timing after you installed the dist.? If yes, I'd say you got a bad distributor(the one you just put in) since all the codes you're getting are directly for sensors located within the distributor.

May 17, 2009 | 1991 Honda Accord

1 Answer

Ignition timing for 1991 Pontiac Firefly or 1991 Chevrolet Sprint or 1991 Geo Metro


for 1991 geo metro 1.0 liter 3 cyl engine the timing is 6 degrees before top dead center. you will need a tachometer because the rpm must be 800 when you set the timing. also you will need to disconnect the vacuum advance to the distributor, and plug the hose to avoid a vacuum leak. (alternate method is to pinch the vacuum advance hose going to the distributor while you are setting the timing) Good Luck!

Oct 28, 2008 | 1991 Geo Metro

Not finding what you are looking for?

Open Questions:

See all 1991 Mitsubishi Galant Questions

1991 Mitsubishi Galant Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...