Question about Hyundai Elantra

1 Answer

I need the timing belt tension for 1997 Hyundai Lantra 1800cc DOHC

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,280 Answers

Go to www.hmaservice.com and register( Vehicle by VIN). Afterward, you have access to shop manuals, service bulletins, wiring diagrams, etc. about your vehicle.

Posted on Oct 19, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1997 Hyundai Lantra - Dash lights don't come on with headlights


Check the fuse. Also make sure your dimmer for the dash lights does is not turned all the way down. If all that checks out, your dimmer may be need replaced.

Oct 17, 2012 | Hyundai Lantra Cars & Trucks

Tip

How to change a timing belt on a hyundai Elantra 1.5 , 1.6 and 2.0 engine


1.5L And 1.6L Engines
  1. Remove all necessary components for access to the timing belt cover, then remove the cover.
  2. Rotate the crankshaft clockwise and align the timing marks so No.1 piston will be at Top Dead Center (TDC) of the compression stroke.
  3. Loosen the tensioning bolt and the pivot bolt on the timing belttensioner. Move the tensioner as far as it will go toward the waterpump. Tighten the adjusting bolt.
  4. Mark the timing belt with an arrow showing direction of rotation if belt is to be reused.
  5. Remove the timing belt.
  6. If defective, remove the timing belt tensioner.

To install:


0900c1528019701f.jpgenlarge_icon.gifenlarge_tooltip.gifFig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L DOHC engines


0900c15280197020.jpgenlarge_icon.gifenlarge_tooltip.gifFig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L SOHC engines
  1. Align the timing marks of the camshaft sprocket and check that the crankshaft timing marks are still in alignment.
  2. If removed, install the timing belt tensioner, spring and spacer with the bottom end of the spring free. Tighten the adjusting bolts lightly with the tensioner moved as far as possible away from the water pump.
  3. Install the free end of the spring into the locating tang on the front case.
  4. Position the timing belt over the crankshaft sprocket, then over the camshaft sprocket. Slip the back of the belt over the tensioner wheel.
  5. Turn the camshaft sprocket in the opposite of its normal direction of rotation until the straight side of the belt is tight and be sure the timing marks align.
    NOTE If the timing marks are not properly aligned, shift the belt 1tooth at a time in the appropriate direction until they are aligned.
  6. Loosen the tensioner mounting bolts so the tensioner works,without the interference of any friction, under spring pressure. Be sure the belt follows the curve of the camshaft pulley so the teeth are engaged all the way around. Correct the path of the belt, if necessary.
  7. Tighten the tensioner adjusting bolt, then the tensioner pivot bolt to 15-18 ft. lbs. (20-26 Nm).
    NOTE Bolts must be tightened in the stated order or tension won't be correct.
  8. Turn the crankshaft 1 turn clockwise until timing marks again align to seat the belt.
  9. Loosen both tensioner attaching bolts and let the tensioner position itself under spring tension. Retighten the bolts.
  10. Check belt tension by putting a finger on the water pump side ofthe tensioner wheel and pull the belt toward the water pump. The belt should move toward the pump until the teeth are approximately 1 / 2 of the way across the head of the tensioner adjusting bolt. Re-tension the belt, if necessary.
  11. Install the timing belt covers and all other related components.
moz-screenshot.jpg6a4c46b.jpg8c77128.jpg74ba305.jpg

on Dec 01, 2009 | Hyundai Elantra Cars & Trucks

1 Answer

Where can i get a diagram or pictures of the engine in a hyundai lantra 1997 1.6


You can get that in pieces from the service and repair manual. You can download that for a small fee here.

Oct 10, 2012 | 1997 Hyundai Lantra

1 Answer

I need to know how to replace a water pump on a 2002 hyundai gx 350.


2002 Hyundai XG350 3.5L MFI DOHC 6cylWater Pump - Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    Negative battery cable Accessory drive belts Water pump pulley Timing belt, tensioner and idler pulley Water pump

  4. 1514f36.jpg

    Fig. Water pump assembly-XG 300 and XG 350 (click over pic for zoom)

To install:
  1. Clean all mating surfaces of any residual gasket material.
  2. Install or connect the following:
    Water pump with a new gasket and torque the bolts to 16 ft. lbs. (22 Nm) Tensioner and timing belt and idler pulley Water pump pulley and drive belts Negative battery cable
  3. Fill the cooling system to the proper level.
  4. Start the vehicle, check for leaks and repair if necessary.
To install:
  1. Clean all mating surfaces of any residual gasket material.
  2. Install or connect the following:
    Water pump with a new gasket and torque the bolts to 16 ft. lbs. (22 Nm) Tensioner and timing belt and idler pulley Water pump pulley and drive belts Negative battery cable
  3. Fill the cooling system to the proper level.
  4. Start the vehicle, check for leaks and repair if necessary.

95486b3.jpg


Fig. Water pump bolt lengths-3.5L engine

Install the water pump with new gaskets and O-rings. Tighten the bolts to the following specifications:
  1. 1.5L SOHC engine: 105-132 inch lbs. (12-15 Nm).
  2. 1.5L DOHC engine: 14-20 ft. lbs. (20-27 Nm).
  3. 1.6L DOHC engine: 14-20 ft. lbs. (20-27 Nm).
  4. 1.8L, 2.0L, and 2.4L engines: 14-20 ft. lbs. (20-27 Nm).
  5. 2.5L engine: 11-16 ft. lbs. (15-22 Nm).

Hope helps (remember rated this).

Jun 18, 2010 | 2002 Hyundai XG350

1 Answer

Timing marks setting Hyundai Lantra


Installation
Ensure timing marks aligned [6] & [7] . 1. Fit timing belt in anti-clockwise direction, starting at crankshaft sprocket. Ensure belt is taut between sprockets. 2. Slacken tensioner pulley bolt [8] . Push tensioner pulley firmly against timing belt to tension belt. 3. Tighten tensioner pulley bolt [8] . Tightening torque: 43-55 Nm. 4. Except Matrix: Turn crankshaft one turn clockwise. 5. Matrix: Turn crankshaft two turns clockwise. 6. Ensure timing marks aligned [6] . 7. Apply a load of 2 kg to belt at . Belt should deflect 4-6 mm. If not: Adjust position of tensioner pulley. 8. Install components in reverse order of removal. 9. Tighten crankshaft pulley bolt [2] . Tightening torque: 170-180 Nm

7 is timing mark on cam,pin mark to top,hole in spoke below pin mark lines up with mark on head
6 is crank timing mark,pin mark on crank lines up with mark on block
NOTE this mark is just before top


Mar 21, 2010 | Hyundai Motor 1996 Elantra

1 Answer

How do i fit rings to my hyundai lantra 1.8, also wrench setting for engine.


You have to use a ring compressor. Available at any auto parts store.

May 16, 2009 | 1997 Hyundai Elantra

1 Answer

Can anybody tell me why elantra keeps popping up when i need a manual for a lantra 1600 is there a manual that matches this from another model


I found the best way is to take the idle pulley off first then with a little effort you can slide it over the cam pulley. Then reinstall the belt tensioner/ idler pulley and adjust. Do not over tension the belt .

Apr 17, 2009 | Hyundai Elantra Cars & Trucks

1 Answer

Timing diagram


there is no timing specs for 97 elantra,if you suspect timing check timing belt,for tbelt alignment diagram get a haynes manaul ,there good for the price

Jan 14, 2009 | 1997 Hyundai Elantra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

167 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...