Question about 1999 Ford F350 Regular Cab

2 Answers

How do you rmove the old ignition lock from a 1999 F-350?

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 82 Answers

The ignition lock or cylinder?..if it is the cylinder, Fords have a very small holl under the cylinder , you will need an small pick , get into the holl and push a pin that hold the cylinder and at he same time pull the cylinder..is easy

Posted on Aug 02, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 65 Answers

Its pretty easy if you now cars you have to push in the pin under the ignition covers to remove it and take aprt the steering wheel to remove another clip from inside there

Posted on Aug 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to rmove and replace radiator drain petcock that is leaking?


These usually just screw out.Some will screw out and then have to be pulled slightly to release a lock tab if equipped.

May 24, 2015 | 1989 GMC S-15 Jimmy

1 Answer

I have a 2001 Lexus RX300. I need to remove the CVJ off the transmission. What is the best way to do that.


jack up car after rmoving wheel, remove lock nut from hub, remove control arms, use cvj fork and pop it off. Fork is similar to one for tie rods.

Aug 02, 2014 | Cars & Trucks

1 Answer

Ignition lock cylinders


Have you had the system reprogrammed? The security system is locking you out.

Mar 12, 2014 | 2002 Dodge Caravan

1 Answer

Replaced old ignition with new one and the new ignition won't lock in place


If the ignition wont lock in place,just redo it but this time you need to realize that you install the key cylinder with the key in the ON postion,straight into the lock cylinder housing,aligning the retaining tabs,on the key cylinder with the hole in the lock cylinder housing.Then turn the key to the off position,

Aug 07, 2012 | 1997 Plymouth Grand Voyager

2 Answers

If i change my ignition after a break in do i need a new key for the doors and ignition too


If the door lock is undamaged then it's fine to use the old key in the door and the new key with the ignition - you then have 2 separate keys for ignition and door -
I dont quite understand the question... could you word it fidderently,
You said you "changed my ignition" - which parts of the ignition?

Jan 22, 2010 | 2000 Nissan Xterra

1 Answer

For Ford F-150 P/U 351 EFI, 1988, ignition problem I can tell you what it is not ignition key switch new, solenoid new, problem , key stays on can jump solenoid and truck runs, to stop must rmove coil wire...


unfortuneately there is no shortcuts....But if there was for sure I'd tell you...it's really not hard....just take off the panelling on the lower and you can sneak it in and out...get back to me...I'M HERE TO HELP!!

Nov 18, 2009 | 1988 Ford F 150

2 Answers

I need to take out old ignition lock cylinder without key on 1989 toyota camry le -lost keys-bought locksmart replacement but it says old has to be in acc position to remove-


This is what the tech manual says.....

Ignition Lock/Switch REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable. If equipped with an air bag, wait at least 90 seconds before working on the vehicle. CAUTION
    Some models covered by this manual may be equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, disable the SRS, as described in Section 6.
  2. Remove the lower steering column cover. Unfasten the ignition switch connector under the instrument panel.
  3. Remove the screws which secure the upper and lower halves of the steering column cover.
  4. Turn the lock cylinder to the ACC position with the ignition key.
  5. Push the lock cylinder stop in with a small, round object (cotter pin, punch, etc.). NOTE: On some vehicles, it may be necessary to remove the steering wheel and combination switch first.
  6. Withdraw the lock cylinder from the lock housing while depressing the stop tab.
  7. To remove the ignition switch, unfasten its securing screws and withdraw the switch from the lock housing. To install:
  8. Align the locking cam with the hole in the ignition switch and insert the switch into the lock housing.
  9. Secure the switch with its screw(s).
  10. Make sure both the lock cylinder and column lock are in the ACC position. Slide the cylinder into the lock housing until the stop tab engages the hole in the lock.
  11. Install the steering column covers and connect the ignition switch wiring.
  12. Connect the negative battery cable.

Jul 26, 2009 | 1991 Lincoln Town Car

1 Answer

HERE ARE THE CODES THAT THE LAST MECHANIC KEPT COMING BACK WITH. 109 ECM, 93 TCS LINK, 71 MAP, 52 ECM, TRANS. DATA QDM1 FAULT, QDM3 FAULT. WHERE WOULD I LOCATE THE IGNITION COIL ON THIS CAR? THANKS,...


The coil will be underneath the distributor cap you have to rmove the rotor to get to it and make sure you number your spark plug wires before you remove them...............

Jun 21, 2009 | 1994 Cadillac Eldorado

1 Answer

How to replace the ignition switch on a 1990 oldsmobile ciera


Loosen steering colum bracket and lower.
unplug electrical connection
turn key to lock postion and rmove the two screws holding to the column.
Installion is the reverse. make sure the new switch is lock postion (slid the switch all the way to left and then back one notch.

Apr 26, 2009 | 1991 Oldsmobile Cutlass Ciera

1 Answer

The ignition is broken, how do I remove it from the column?


id call a locksmith to rmove it and then go to auto zone and buy a new ignition there is not an easy way to remove it and the ock smiths have all the right tools and can do it fast

Jan 19, 2009 | Ford Focus Cars & Trucks

Not finding what you are looking for?
1999 Ford F350 Regular Cab Logo

Related Topics:

184 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...