Question about 1994 Oldsmobile Cutlass Supreme

Open Question

94 cutlass supreme 'check gauges' and 'airbag' lights

My 94 cutlass supreme 'check gauges' and 'airbag' lights are flickering on/off. any suggestions?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 321 Answers

SOURCE: 1995 cutlass supreme transmission

It physically will fit and bolt up,but there are many different ratio,and drive and driven sprocket tooth counts,different final drive ratios,all monitored by the computer with electronic speed sensors.If the trans from the 95 has a different ratio than the 93,the computer will set gear ratio error codes,and possibly put the trans in a failsafe mode,stuck in 2nd or 3rd gear.On the transmission case,down by where the passenger side axle would go in,is a thin metallic tag,maybe 2"x 3",and it has bar codes,and also a series of numbers and letters.The numbers and letters,large cap,are the final drive gear ratio code.They should match on the two transmissions in question.

Posted on Jul 31, 2008

Ad
muttandjeff
  • 359 Answers

SOURCE: 93 olds cutlass . oil pressure gauge when started car todaygauge did not moveoil level fineruns perfectguage just at low end of guage

2 things come to mind check the negative terminal of battery and the ground wire connected to engine location varies where they connect these but will always originate from neg on battery a quick check to see if you have a proper ground connection is to take one booster cable and connect to neg post on battery and connect the other end to the engine on clean metal (be sure to keep clear of moving parts ) start engine and see if you have pressure on gage if so you must clean ground connection to engine .if this does not correct possible bad sending unit in side of block with one wire connected to it . caution ** temperature sending unit look similar so make sure with one you are taking out

Posted on Dec 23, 2008

c17hydro
  • 2984 Answers

SOURCE: how do I remove rear brake pads on 94 olds cutlass

Please don't forget to rate! This helps us help you!

1993–96 Vehicles

  1. Remove about 2⁄3 of the brake fluid from the reservoir with a clean syringe or baster type utensil.
  2. Raise and safely support the vehicle.
  3. Matchmark the relationship of the wheel to the axle flange. Remove the wheel and tire assembly.
  4. Reinstall two lug nuts to retain the rotor.
  5. Unfasten the bolt and washer attaching the cable support bracket to the caliper body assembly. It is not necessary to disconnect the parking brake cable from the caliper parking brake lever or disconnect the brake hose unless the caliper is to be completely removed from the vehicle. Freeing the cable support bracket allows enough flexibility in the cable to pivot the caliper up and down and remove the shoe and lining.
  6. Remove the sleeve bolt.
  7. Pivot the caliper body assembly up. Do not completely remove the caliper assembly body.
  8. Remove the outboard and inboard shoe and linings (pads) from the caliper support.
  9. Remove the two pad clips from the caliper support. To install:
  10. Bottom the piston assembly into the caliper bore. Use a suitable spanner-type tool in the piston slot to turn the piston assembly and thread it into the caliper body assembly.
  11. After bottoming the piston, lift the inner edge of the boot next to the piston assembly and press out any trapped air. The boot must lie flat. Make sure the slots in the end of the piston are positioned correctly before pivoting the caliper body assembly down over the shoe and lining in the caliper support. Use a suitable spanner-type tool in the piston slots to turn the piston as necessary. NOTE: Whenever installing new pads, install new pad clips. These should be provided in the disc pad kit.
  12. Install the two pad clips in the caliper support.
  13. Install the outboard and inboard shoe and lining in the caliper support. The wear sensor is on the outboard pad. The sensor is positioned downward at the leading edge of the rotor during forward wheel rotation. Hold the metal shoe edge against the spring end of the clips in the caliper support. Push the shoe in toward the hub, bending the spring ends slightly, and engage the shoe notches with the support abutments.
  14. Pivot the caliper body assembly down over the shoe and lining assembly. Be careful not to damage the piston boot on the inboard. Compress the sleeve boot by hand as the caliper body moves into position to prevent boot damage.
  15. After the caliper body is in position, recheck the installation of the pad clips. If necessary, use a small prytool to re-seat or center the pad clips on the support abutments.
  16. Install the sleeve bolt and tighten to 20 ft. lbs. (27 Nm).
  17. Install the cable support bracket (with the cable attached) with the bolt and washer. Tighten the bolt to 32 ft. lbs. (43 Nm).
  18. Remove the two lug nuts retaining the rotor.
  19. Install the wheel and tire assembly, aligning the marks made during removal.
  20. Carefully lower the vehicle, then firmly depress the brake pedal 3 times to seat the pads against the rotors.

Posted on Jul 15, 2009

c17hydro
  • 2984 Answers

SOURCE: where is the location of the battery in a 94'

Pictures coming next!

CAUTION Always make sure that the ignition is OFF when disconnecting or connecting the battery cables. Failure to do so may cause damage to the computer control module or other electronic components.

  1. Make sure the ignition is OFF . Remove the air cleaner assembly if necessary, and disconnect the negative battery cable, then the positive cable.
  2. Unfasten the retaining bolts, then remove the cross brace.
  3. If equipped with Anti-Lock Brakes (ABS), remove the relay center and bracket, then position aside.
  4. If necessary, detach the electrical connector and hose from the windshield washer pump, then unfasten the reservoir retaining nut and remove the reservoir.
  5. Remove the air cleaner bracket upper attachment bolt.
  6. Unfasten the battery heat shield, hold-down bolt, and retainer.
  7. Remove the battery from the battery tray.
To install:
  1. Place the heat shield on the battery, then position the battery in the vehicle.
  2. Install the retainer, air cleaner bracket and hold-down bolt. Tighten the hold-down bolt to 13 ft. lbs. (18 Nm).
  3. Install the air cleaner bracket upper attachment bolt. Tighten the bolt to 35 inch lbs. (4 Nm).
  4. Position the windshield washer reservoir and secure with the retainers. Attach the hose and electrical connector to the windshield washer pump.
  5. If equipped with ABS, install the relay center bracket and relay center.
  6. Position the cross brace, then secure with the retaining bolts. Tighten the front bolt to 18 ft. lbs. (25 Nm) and the rear bolt to 35 ft. lbs. (47 Nm).
  7. Connect the positive battery cable, then the negative battery cable. Tighten the cable bolts to 11 ft. lbs. (15 Nm).
  8. If removed, install the air cleaner assembly.

Posted on Oct 20, 2009

  • 564 Answers

SOURCE: 1994 oldsmobile cutlass supreme sl the fuse box for signal lights

the fuse box will be in 1 of 3 places (1)glovebox (2)under dash by drivers foot kick panel or (3) under hood .

Posted on Nov 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Gauge indicator light on. 1994 olds cutlass supreme


launched it and this is going to give u an idea whats is happening .cutlass supreme are very easy to understand ..sometimes is a real failure or sometimeis a wrong action of your driving and ecu detected it as a fail.. be more specific please

Sep 15, 2014 | 1994 Oldsmobile Cutlass Supreme

1 Answer

My 94 Oldsmobile cutlass supreme brake lights won't work, the blinkers and parking lights work


well you should check the fuses under the dash and if that's not it so models have more fuses under the hood.

Jan 29, 2011 | 1994 Oldsmobile Cutlass Supreme

1 Answer

'94 Olds Cutlass Supreme Door Handles


You have to find the linkage and pull it. If yu cannot find the linkage, one trick is to go to a self serve wrecking yard and play with one of the 90s olds by removing the door panel and looking at it to see how it works.

Apr 05, 2010 | 1994 Oldsmobile Cutlass Supreme

1 Answer

1994 olds cutlass supreme volt gauge shows low have


Could be .. did you do any voltage checks? I suggest you check altenator output as well as battery voltages under various circumstances.

Mar 24, 2010 | 1994 Oldsmobile Cutlass Ciera

1 Answer

Need a transverse spring for 1194 cutlass supreme


that's what most people call it, go to the local salvage yard get one off a 92-93-94 olds, chev luminia

Mar 17, 2010 | 1995 Oldsmobile Cutlass Supreme

1 Answer

94 oldsmobile cutlass supreme, car won't start and security light comes on.


problem could be the ignition key and switch or the theft deterrent module relay is bad or the theft deterrent module is faulty.this is a dealership fix.

Dec 06, 2009 | 1994 Oldsmobile Cutlass Supreme

2 Answers

92 olds cutlass supreme turn signal broken


Start by checking the fuses that's simple
than relay than bulbs
last you may have to remove the steering wheel and than replace the entire signal assembly those are pretty much all your options so start with 1 and work your way down the list

Sep 24, 2009 | 1992 Oldsmobile Cutlass Supreme

Not finding what you are looking for?
1994 Oldsmobile Cutlass Supreme Logo

Related Topics:

186 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...