Question about 1996 Jeep Cherokee

1 Answer

My turn signals worked when I left my house and when I reached my destination they did not work. I cheked my fuse and the fuse was fine but you where the fuse plugs into on the fuse block ( #8 ) there is only one side that has the conection. did it get pushed thru? How do I fix this? I cant drive without my blinkers!!! Please Help its a 1996 2 WD Jeep Cherokee 6 cyl

Posted by on

  • Kymberly Murphy Aug 01, 2009

    I tried to remove it and couldnt. I took the two long screws out of the fuse block and then relized it would not come apart so I looked under the hood and I thought that the black looking thing would pull apart from the fuse block but it didnt so if you could kinda give me a little more info on removing it that would really help me thanks



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,088 Answers

The plastic panel under the fuses and relays can be removed (all components removed). Pull the negative battery terminal connection first.

Posted on Aug 01, 2009

  • drallim Aug 02, 2009

    I did this on a '96 Dodge caravan in the late '90s. It isn't a recognized service procedure, so it was peck with it until the method appeared. As I recall, the long sides of the fuse box spread apart to release the panel. I may have been looking for a similar problem, but different circuit. Seems like it didn't matter anyway as the problem was somewhere else. Don't know if this helps. You might look for the flasher unit under the dash



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer


Do turn signals work ok? Do you have current at the brake switch?

Feb 07, 2014 | 1999 GMC Suburban

2 Answers

Left rear light won't work using turn or brake, running light good

You can purchase a haynes or chiltons guide those will have that information and more. Have you replaced all of the bulbs within that light? sometimes one bad light can make them all not work right.

Jun 19, 2008 | 2001 Ford Explorer Sport

1 Answer

2000 towncar signals stopped working?

There should be a turn signal fuse in the fuse box inside the car, and there is a flasher for the hazards and one for the turn signals.
Check your owners manual for more info.

Aug 25, 2012 | 2000 Lincoln Town Car

1 Answer

I broke my turn signal light when i tried to change it. i used a napkin to get the rest out and when i did, the napkin caught fire. i put it out and finished changing the signal. later i found out that i...

I'm not seeing any model or year, so we'll go to basics. I would start by pulling the light socket completely out of the housing, inspect wires going into it on back side, and cut them back to a good clean looking spot but not too short that it won't reach back to housing, and replace the entire socket, then try a good bulb. Wires and/or contacts are likely melted together in there and should be changed before digging deeper in to the problem that started right there. It may be all you have to do.

Apr 02, 2011 | Ford Thunderbird Cars & Trucks

1 Answer

Jaguar xj6 break light cancels signal

Replace the turn signal switch. Bad contact inside causing a crossing of the circuits. When the turn signal is applied it should open the brake light circuit allowing for just the signal to work. Doesn't sound like the switch is doing it's job.

May 23, 2010 | 1989 Jaguar Vanden Plas

1 Answer

I have a 2004 Chevy TrailBlazer that just developed a problem with the left turn signal. The left turn signal indicator on the dash is blinking rapidly and the tail light turn signal is out. I change out...

The Trailblazers have a common problem with the printed circuit boards in the tail lamp housing.
Unplug the tail lamp housing at the wiring connector and test for power with a test light. ( With turn signals on) You may have an open circuit in the lamp housing circuit board. Good luck

Apr 02, 2010 | 2004 Chevrolet TrailBlazer

1 Answer

Chevy S-10 1999, Left rear turn signal is not working

With a test light or better yet a digital multimeter, must check and see if current is reaching the conductive points on the inside of the lamp holder. Most faults are due to oxidation or broken wire(s).

Sep 26, 2009 | 1998 Chevrolet S-10 Pickup

1 Answer

No brake lights or turn signals on 2008 F450

try checking all of your fuses and see which ones are blown. you have two sets of fuses and they are under the hood of the vehicle and under the dash on the driverside or in the glove box. if the don't work after changing the fuses then your wiring for the turn signals and brake lights need to be cheked from the fuse boxes to the swith for the trurn signal and to your brake lights

Mar 24, 2009 | 1999 Ford Super Duty F 450

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

109 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides