Question about 2003 Hyundai Tiburon

3 Answers

Replaced OEM clutch and flywheel

I just replaced the OEM clutch and flywheel in my 03 Tiburon with a Gripforce Stage 2 clutch kit with lightweight flywheel. My problem is that when I press the clutch pedal, there is no back pressure and the pedal goes to the floor. I thought that it may be an air bubble in the line but that's not it. Any suggestions?

Posted by on

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Check your master clutch cylinder I replaced my clutch and had the same issue and had to replace the master clutch cylinder and now my clutch works great

Posted on Aug 02, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,623 Answers

Hello hhmit_2000...Sounds lik you stil have a a little air trapped in the system..air wil compress, fluid wont.
Hydraulic clutch systems are difficult to bleed, it takes many times to get the air out of the system. Also, a vacuum bleeder or a pressure bleeder will aid in the process. If you open the line at the bottom, at the fitting, just open it and let the fluid flow. But, do not let the the fluid get too low in the reservoir. Once fluid will flow, on its own, close the valve, and bleed the clutch with the pedal...Also you can check the slave cylinder, the 03's are know to be faulty due to a bad check valve. There was a techincal service bulletin released on it.. Check your master cylinder, it may be faulty.
Good luck, i hope this helps, please rate me a fixya.

Posted on Aug 02, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 986 Answers

I hope you did not put the clutch in backwards

Posted on Aug 01, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No reverse in my 2006 Hyundai Tiburon hatchback 5 speed what could be problem


"Car won't go in reverse" - New Tiburon Forum : Hyundai Tiburon ...

www.newtiburon.com/forums/.../189049-car-won-t-go-reverse.html

Aug 8, 2010 - 23 posts - ‎16 authors
Okay guys I just sold my 03 tiburon GT 6 speed to a 16 year old. I just got a ... Join Date: Sep 2006. Location: ... "It stalls and just drift forward, no reverse lights" Now did he break somethng or is he putting it in 6th..... Any Ideas. ... To view links or images in signatures your post count must be 5 or greater. Location of reverse light switch? - New Tiburon Forum ...
8 posts
Jul 23, 2014
So who's reverse lights don't work? - New Tiburon ...
25 posts
Apr 11, 2009
More results from www.newtiburon.com
Missing: hatchback

2003 Hyundai Tiburon Manual Transmission Complaints

www.aboutautomobile.com/.../Hyundai/Tiburon/Manual+Transmission
My 2003 hyundai tiburon clutch and flywheel broke on 3 separate occasions since ...into reverse, I had a hard time finding it, it would not let me put it into reverse and I ....2006; Description of the Complaint: I have 2003 v6 tiburon, clutch failed at ... bought 2004 5 speed tiburon (she bought it before my problems started) and ...

Transmission Won't Shift/CEL Due to Failed Speed Sensors ...

repairpal.com > Problems > Hyundai > Sonata

Jan 03, 2016 | Hyundai Cars & Trucks

2 Answers

What should it cost to repair a clutch on a 2001 passat 2.8 They told me a flywheel ranges anywhere between 500.00 and 1000.00


you can find an oem flywheel for a little over $500 on line and I found off brands for less than $400-but why are they convinced the flywheel has to be replaced? If it hasn't been removed yet, I'd stay away from them, it may only need to be removed and resurfaced. It may need nothing done to it-

Mar 03, 2011 | 2001 Volkswagen Passat

1 Answer

Just replaced the clutch because the car wasnt going in to gear without force and grinding. replace the clutch and still the same problem. even pulle the arm manually witha bar to release it and still no...


that center piece is the pilot bearing, the input shaft should ride free , if it is indeed chewed up the shaft is probably binding in the flywheel

Nov 24, 2009 | 2003 Hyundai Tiburon

1 Answer

We have installed a new clutch kit, flywheel, master cylinder,slave cylinder and a few other random parts in my son's 03 Tiburon, yet the clutch simply will not engage. Any ideas on how to fix this, the...


Well it sounds like you have done the right thing like replacing the lot not just a centre platr BUTwhat you have done by the sound of it if you push in the clutch and the g/box just grinds and wont look like going in then your problem is that you have the CENTRE plate around the wroug way as the part with the springs etc have to go into the pressure plate housing ASyou have it its jamed up on the bolts on the Flywheel
TAKE it off change it around and away you go But make sure you have bleed the clutch and it should drive 1" off the floor and if so then you have done a good job...Let me know how you go Ron
Are you on Skype??

Oct 13, 2009 | 2003 Hyundai Tiburon

1 Answer

2003 Hyundai Tiburon making a weird noise


Hello mpolci...The 2003 Tiburon was sold to the public with a defective clutch, it failed due to warpage and bad pressure plate... among other things. There are MANY class action lawsuits. Did you resurface or replace the flywheel when the clutch was replaced? Did you go with an aftermarket clutch kit, or factory? Also the slave cylinder on the 03 was known to have a defective valve.
You can try checking the levels and bleeding the system and if you still have problems, then it could be a release bearing, a loose clutch pad, or a broken pressure plate spring....If the clutch is still under warranty, i would return it to the installer.
Good luck, i hope this helps...please rate me a fixya.

Aug 01, 2009 | 2003 Hyundai Tiburon

1 Answer

03 tiburon clutch torque specs


your torque specs for clutch to flywheel
15-22NM

Jul 11, 2009 | Hyundai Motor 1997 Tiburon

2 Answers

Clutch and flywheel are shot in my 06 tiburon w 22k


cluthes -brakes -belts ect are a wear out problem no dealer will do any thing for you with these problems-only internal engine and trans problems will they fix.I repair vehicles every day and have people with problems like this from every manufacturer =had a 04 kia with 50k miles break a timing belt and smash all the valves and put a hole in a piston,motor shot KIA told cust to go away as warranty was up,evan had extended wrty,it seems there warranty starts the day it leaves prodution line,I,m sorry for your problem but you are not alone with dealers doing this.

Mar 16, 2009 | 2006 Hyundai Tiburon

1 Answer

2003 Tiburon 6 spd clutch replacement now tranny won't respond


Possibility, you may have intalled the clutch disk backwards.... if so, the disk hub is torqued against the crankshaft hub preventing engagement of the clutch. 2003 TIBUORN DUAL MASS FLYWHEEL AND CLUTCH DISC ASSEMBLY INSTALLATION PROCEDURE DESCRIPTION: The 2003 MY 2.7L Tiburon vehicle equipped with the 6-speed manual transaxle employs a dual mass flywheel system. The 2003 Tiburon Shop Manual does not show the clutch disc assembly with the dual mass flywheel. This bulletin provides information about how to assemble these components. NOTE Although it is possible to assemble the clutch disc with either side facing the flywheel surface, only the assembly of these two parts shown in this bulletin is correct.
PARTS ASSEMBLY:
  1. Attach the dual mass flywheel to the engine crankshaft assembly.
  2. Identify the clutch disc flange side and the collar side as shown. 0240025a.gif
  3. Install the collar side of the clutch disc on the dual mass flywheel surface so that the flange side is facing the pressure plate side as shown. 0240025b.gif
  4. Attach the pressure plate to the dual mass flywheel and complete assembly of the remaining components per the Shop Manual procedures. 0240025c.gif

Dec 14, 2008 | 2004 Hyundai Tiburon

Not finding what you are looking for?
2003 Hyundai Tiburon Logo

273 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

78289 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...