Question about 1998 Cadillac Catera

2 Answers

I just changed my brake pads and the brake sensor light came on. Wonder why? And how to turn it off??

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,486 Answers

Make sure you have not pulled on any wires and losend the plugs.Pull the plugs apart clean them and replace.If the fault is that then the light will go out after driving a few hundred yards.Good luck hope that was helpfull.

Posted on Aug 01, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,976 Answers

Bleed the brakes and check the adjustment on the parking brake.

Posted on Aug 01, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brake Light on Dash


Have you tried bleeding the brakes? Sometimes air in the lines causes the break trouble light to come on.

Jul 14, 2017 | 2005 Porsche Boxster Convertible

2 Answers

Replace brake pad light on, how do you reset it?


you need to replace the pad wear sensor when the pad wears down it wears the sensor and the sensor needs to be replace if you look at the sensor you can see the wire on the sensor wears threw

May 19, 2012 | 2009 Audi Q7

1 Answer

Brake pad wear indicator light does not go off at the dash after changing rotors brake pads and the sensor in the front wheels all pads and rotors and the sensor is ok at rear. the vehicle has only 30000...


Did you change the sensor? if you did, do a battery reset (disconnect for 10 to 20 min.).

Obviously the wear sensor has made contact with the rotor and is already damaged. You're not even suppose to resuse the wear pad sensor if its worn or damaged anyways.The way how the sensor works is that it must make contact to the rotor to complete the wear pad light indicator circuit. There is no mentioning that he replaced the the wear pad sensor with a new one.

But if one did replaced the wear pad sensor and the wear pad indicator is lit up, the way to reset it is to leave the key on in ignition switch #2 or #1 for about 30sec. turn it off and its reset.

Its possible that you forgot to replace the brake light sensors. They are about 15 bucks, and have to be replaced in order for that light to turn off. You can either get them from the dealer where they'll likely charge you 3 times as much, or you can go to http://www.turnermotorsport.com and get them there.

You have to reset the light by leaving the ignition switch on position #2 for about 30 sec. turn off the ignition and start the engine up and see if it goes out. I recommend buying a new wear pad sensor as well because now light will lit up when you're way below spec (less than 3mm)

Also, you could try with this procedure for one E39: Turning off the Check Brake Linings warning on the Instrument Cluster...
- so you've just changed the brake pads on your E39, along with the wear sensors. The old sensor(s) needed replacement cause you waited a bit too long before changing the pads, and wore through the sensor(s), turning on the BRAKE light on the dash. But wait, the light is still on? But there's a new sensor installed... what gives?!
- there is a procedure required in order to turn off the light/warning. With the ignition off, step on and hold the brake pedal. Now, while holding the brake pedal down, turn on the ignition switch to position 2 (just before cranking). Hold the brake pedal until the BRAKE light is off. Tada, the warning is gone and reset.

NOTE: This procedure worked on a 2001 E46 325i. It took about 15-20 seconds, but it cleared out w/o having to unhook the battery.

Other details find in the Owners Manual 2006-BMW-Z4m-Roadster-Owner-Manual

Keep us updated.

Nov 04, 2010 | 2006 BMW Z4 Roadster

2 Answers

I have 2000 isuzu rodeo lse replace brake pads and


CHECK SENSOR ON THE PADS, OR BRAKE SIDE

Jul 24, 2010 | 2000 Isuzu Rodeo

1 Answer

ABS and service light reset after brake change


the ABS light resets itself every time the key is turned off and on, it is self testing and will only turn the light on when there is a problem in the ABS system, worn out brakes don't cause the ABS to come on, if the light is on the system has a fault present and it must be tested with a factory system scanner to determine the source of the fault or at least the area that is causing the problem, that can be one of the four wheeel speed sensors, a defective ABS hydraulic control unit and sop on.

Jul 02, 2010 | 2003 Renault 181

3 Answers

How to reset brake light after changing pads.


Hi Peters6709,
Sorry to tell you, but you need to replace the pad-wear sensors as well. They are the little trapezoid pieces that hang inside the tops of the inside pads. They should run about $10 each. Once replaced, disconnect the battery completely for about 10 minutes, if you have a stock radio keep the code handy.

Next time check the pads every 10-12K miles. I have been running the SAME pad wear sensors on my Z3 for the past 2 pad changes now after making the same mistake the first time.

Best of luck!

May 02, 2010 | 1999 BMW 323 Series

3 Answers

How to shut off Brake wear sensor after pad change


If the brake pads were worn enough to activate the warning light the sensor or sensors must be replaced. There is no reset for this.

Oct 24, 2009 | 2004 Lexus LS 430

2 Answers

I replaced the front pads on a VW JETTA 2.5 and the check pads light is on. How can I reset the check pads light?


As the brake pads wear, the brake pad wear sensor contained in the brake pad contacts the brake rotor. This causes the sensor to fail. When a pad wear sensor fails it opens the ground circuit of the pad wear warning light system causing the pad wear warning light to illuminate. Perform normal brake service to correct this condition and be sure to replace the brake pads with pads containing wear sensors. Once the brake pads and wear sensors are replaced, reset the brake pad warning system by turning the ignition switch to the "on" position. As long as continuity to ground exists through all the brake pad wear sensors the system should reset and the pad warning light in the dash will go out. If the pad warning light does not go out, a check of the pad warning circuit for an open circuit condition or poor ground must be performed.

Mar 03, 2009 | 2005 Volkswagen Jetta

3 Answers

BRAKE WARNING LIGHT


I dunno if this will work on your BMW, but on my BMW Z3 and M3, it was....

Turn the ignition key to position 2, but do NOT start the car. Wait for about 45 seconds and the brake warning message will be reset.

If it doesn't reset, then the brake sensor was damage. You will need to replace the brake sensor. It sounds like you replace the brake right after you saw the warning, so the brake sensor should be okay.

Dec 19, 2008 | 2003 BMW 325

4 Answers

Brake Pad Sensor


On my bmw 325i front pads changed,indicator on dash still on,help!!

Jun 11, 2008 | 2003 BMW 325

Not finding what you are looking for?
1998 Cadillac Catera Logo

Related Topics:

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...