Cars & Trucks Logo

Related Topics:

A
Aucencio Chavez Posted on May 31, 2018

I replaced the kickdown assembly in the tranny of my 2007 dodge ram 1500 now it won't crank can someone please help

5 Related Answers

ahill_1

Big A's Auto Repair

  • 755 Answers
  • Posted on Dec 27, 2008

SOURCE: 2000 dodge ram 1500 speed sensor location

Hi my name is Allen!

The sensor you are looking for is located in the rear diff housing, its mounts on top of the housing it is also used for ABS if equipped.

For further asistance you may reach me through FixYa!

Ad

Anonymous

  • 840 Answers
  • Posted on Feb 02, 2009

SOURCE: passanger side mirror replacement on 04 dodge ram 1500?

very easy take the mirror inside cap off if you can not get to the 3 bolts then you will have to take trim panel off to take trim panel off look for plastic caps take them out and unscrew them then pop out the bottom of the door and pop the sides out then lift up and out should be loose enough for the bolts now/ 10mm bolts 3 Please rate my response thank you very much

Anonymous

  • 1 Answer
  • Posted on Feb 15, 2009

SOURCE: remove front axle from differential on 2003 dodge ram

That works fine on a relatively new vehicle but one that has run in salt etc you'll save a lot of time if you remove the steering knuckle completey by separating lower ball joint and outer tie rod end ball joint and bring the whole steering knuckle to a bench to separate the hub/bearing. Soak everything with penetrant, loosen the bolts a few turns and try hitting right on the bolt heads. I also made a very sharp wedge from a chisel and rammed it hard on the other side to seoarate the hub. It will finally come apart then you'll see all the **** that was binding it due to an alumininum knuckle re-acting with a steel hub. Clean the hole and grease everything and fit new bearings

ZZZoom

  • 151 Answers
  • Posted on May 10, 2009

SOURCE: check engine light on code

This trouble code is Evap Purge System Performance fault. 1) Check for a loose or missing fuel cap. 2) Check for a damaged or missing fuel cap seal. Recheck for other trouble codes. This fault wont cause the stumblering problem. It turns on the MIL lamp to say there leak in the EVAP system.

Anonymous

  • 582 Answers
  • Posted on Aug 19, 2009

SOURCE: Dont know what kind of Transmission my dodge has

ON THE BOTTOM OF THE TRANY THERE IS A TAB ON THE SIDE OF THE TRANY ON THE BOTTOM LIP WHERE THE FILTER PAN IS BOLTED THE NUMBERS ARE STAMPED ON THE TRANY HOUSING ON THE BOTTOM NEXT TO THE PAN

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

2006 Dodge Ram 1500 5.7 Hemi. What's wrong with my truck?

Dodge Ram 1500/2500 (2002-2009) fuses

Fuse Box Diagrams https://fuse-box.info > dodge > dodge-ram-1500-2500...

Fuse box diagram (location and assignment of electrical fuses) for Dodge Ram / Ram Pickup 1500/2500 (2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009).

Not good fuses to blow. you need to find out why?

31
31 10 or 15 amp except SRT (2006) (15A): Shift Motor and Mode Sensor Assembly (ETC), Powertrain Control Module (Gasoline);

2007-2008 (10A): Powertrain Control Module;

2008-2009 (15A): Powertrain Control Module


4
40 20amp
Base: Power Outlet - Instrument Panel, Power Outlet - Lower Console (2007-2009)
Here are your dash warning lights. The lightning bolt is Electronic Throttle Control, and you can't drive without that. Not sure that your sail and sun is unless it is the Cold Ambient Derate Mode Indicator
You need a local auto electrician. you can't guess stuff like this, it needs a pro grade scan tool computer.

https://www.google.com/search?q=auto+electrician+near+me

..
0helpful
1answer

2001 dodge ram 1500 wont stay running when i start it. could it be because of the tranny housing bolts missing or not tight?

unlikely unless on of the loose bolts is the ground point for the battery
run the fault codes
could be crank or cam position sensors from bad harness connections
1helpful
1answer

Dodge Ram 1500, air would only work on high (fan), then quit working totally. Replaced blower resistor and still won't work.

You sometimes have to put something between the cage and the motor and tap on the shaft. Often times the cage breaks apart.
Soaking the shaft with WD40 or other product may help break it loose.
2helpful
2answers

99 dodge ram 1500 4x4. dosen't want to shift from 2 to 3 until you completely let off gas and rpm's drop. any ideas?

your kickdown lever/cable is starting to sieze. lubracate the kickdown cable, then inspect the kickdown linkage as it could be a broken cable clip.
0helpful
1answer

Does a dodge ram 1500 have a cam or crank censor?

The 3.9L 5.2L and 5.9L engine use the distributor assembly as your cam sensor . The crank sensor is on right rear attached to engine block (behind cylinder head)
2helpful
3answers

2000 dodge ram 1500 speed sensor location

Hi my name is Allen!

The sensor you are looking for is located in the rear diff housing, its mounts on top of the housing it is also used for ABS if equipped.

For further asistance you may reach me through FixYa!
0helpful
1answer

Engine stalls in drive after check engine light came on.

Have it sacnned for a code. it seems to be the speed sensor at the tranny.or the crankshaft position sensor. hope this helps. will you please vote ?
Not finding what you are looking for?

48 views

Ask a Question

Usually answered in minutes!

Top Dodge Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...