Question about 1999 GMC Suburban

1 Answer

Starter for a 1999 GMC Surburban

My rebuilt starter has 3 screws with nuts and the old starter has only 2 so which 2 do i use

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,392 Answers

Get the correct starter first off. If your new one has 3 holes, and the old one 2, it is not correct for your vehicle. IF you would like to make it work, use the holes that line up with your old one.

Posted on Aug 05, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

1999 surburban won't start getting gas and fire. put new coil and check fuel pressure from fuel pump. what can it be,


my 1999 chevy suburban will start with starter fluid bbut wont stay running already replaced coil,rotor on distribitor,and oil pump cant seem to figure it out any ideas

Jan 17, 2011 | 1999 GMC Suburban

1 Answer

I have a 1999 isuzu rodeo 2WD 3.2L V6. What are the steps in replacing my starter. My car is stranded and i need to try to replace it myself?


The repair manual book says first disconnect the battery , then lift the car to have more space to work on it make sure that is secure if you liftit ,remove the nut to Starter ,also nut to solenoid cable ,or if you think it is easier take off starter first and then after remove nuts to starter and solenoid ,then you ready to install you new or rebuilt starter ,,good luck

Nov 26, 2010 | 1999 Isuzu Rodeo

1 Answer

How to remove a starter from a 1999 chevy silverado 4x4 pickup


1) Disconnect Negative Cable on Battery
2) Starters on right-side Close to Trans. Bell Housing
3) Remove the 2-Starter Bolts and Shim if it's
if it has shims.
4) Remove the wires off Solenoid: Mark Them:
5) Remove the Heat Gaurd Over top of Starter:
6) Take Starter on Out.

To Re-Install Reverse the Procedure that you Removed the Starter. NOTE: the Shims if there was any are only nessary if the Casting of the Starter is not Exactly or Close to The Original.

Be sure that All the Wires you Took off the Starter Solenoid are put Back on the Exact Same Terminal. And Snug them up .Be careful not to Over Tighten,:
Specs on Bolts Are :
Torque Starter Battery Cable Nut to 90 inch lbs
Torque Smaller ingnition wier nuts to 18 Inch Lbs
Torque the 2- Starter Mounting Bolts to 35 FOOT lbs.
Remember if your Old Starter Had Shims the New one MIGHT need Shims.All Starters Casting are just a Little Different. like by thousands of an inch. So if you have problems you might have to remove or add shims,they come in different sizes. Hope this has helped you,Please let me know how this solution Helped. Thank You: From d_hubbs

Jun 07, 2010 | 1999 Chevrolet C1500

1 Answer

How to change a starter on 1984 chevy c10 with a 305


First disconnect the power cable from the battery. If your starter has a mounting bracket on the nose undo that nut first ( some have, some don't). Undo the nut that holds the battery cable to the starter and remove the wires ( count them so you know how many go back on). Under the truck you have to remove the inspection cover from the front of the transmission next to the motor. Undo the 2 bolts on the bottom of the starter. When these come out the starter will drop so be prepared because you still have 1 wire attached. Ease the starter down and remove the small wire from the inside of the solenoid and take the starter out with you. When you get the rebuilt starter from the autoparts store make sure you get a new solenoid. An old solenoid and a new starter is kind of like recycling used toilet paper, possible but not worth the trouble. It goes back in the reverse of taking it out.
BE CAREFUL putting the small wire back on the new solenoid. It has to be tight but you can easily strip it if you get carried away with it. If by chance that happens just double nut it with the nut from the old one and you'll be okay. Hope this helps.

Dec 19, 2009 | 1984 Chevrolet Chevy

1 Answer

How to replace a starter on 1994 gmc sierra 1500 with a 350 engine


unhook the battery, there are 2 wires on the starter solenoid, 1 is a 5/16 nut and the other is a 9/16 nut remove those wires. this maybe easier to remove the heat shield first. next ther are two 9/16 bolts holding the starter in position, remove, and the starter will come out, about a 15min job

Sep 27, 2009 | 2000 GMC New Sierra 1500

1 Answer

How do you replace a starter from a 1999 Ford Ranger 4x4 pickup with 3.0L V6 without pulling the engine?


This Seems Pretty Cut & Dry Although I Have Removed Exhaust to Gain Access to Starters on the 3.0L THIS IS Instructions PER> ALLDATA

REMOVAL

WARNING: WHEN REPAIRING STARTER MOTOR OR PERFORMING ANY MAINTENANCE IN THE AREA OF THE STARTER MOTOR, NOTE THE HEAVY GAUGE INPUT LEAD CONNECTED TO THE STARTER SOLENOID IS HOT AT ALL TIMES. MAKE SURE THE PROTECTIVE CAP IS INSTALLED OVER THE TERMINAL AND IS REPLACED AFTER REPAIR.

  1. Disconnect the battery ground cable.
2. Remove the ground strap bolt
3 Remove the nuts and lower the starter motor.
4 Remove the cap
  1. Remove the terminal nuts and remove the starter motor.
INSTALLATION
  1. Follow the removal procedure in reverse order.

Aug 01, 2009 | 1999 Ford Ranger SuperCab

1 Answer

Terminals on GMC 1989 replacement starter


your new starter should have a S and a R terminal and also a large terminal thats for your main power . funny thing is im having starter problems with same truck man.

Mar 06, 2009 | 1989 GMC Sierra

1 Answer

Not able to reach the wires on my starter on 1996 gmc surburban


Look under the hood on the pass. side and down by the frame you will see the main power wire that runs from the batt. down to the starter.There is a wire clamp that has a 13mm bolt which secures the wire to the frame.Taking this off will allow more slack to pull the starter down further to access the wire.

Mar 01, 2009 | 1996 GMC Suburban

1 Answer

Starter runs constantly when u connect the battery just replaced the engine in my 99 gmc jimmy. cant find pinched wires, we think its a ground problem. but dont know where to start looking


Check the wire from the battery at the starter there is a tab to keep it from spinning when you tighten the nut,it may be touching the other nut on the solenoid causing the starter to spin.You can also remove the wire on the solenoid that engages it then it should not spin.If it does it is a starter problem

Nov 23, 2008 | 1999 GMC Jimmy

Not finding what you are looking for?
1999 GMC Suburban Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...