Question about 1999 Ford Ranger SuperCab

1 Answer

How do you replace a starter from a 1999 Ford Ranger 4x4 pickup with 3.0L V6 without pulling the engine?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,596 Answers

This Seems Pretty Cut & Dry Although I Have Removed Exhaust to Gain Access to Starters on the 3.0L THIS IS Instructions PER> ALLDATA

REMOVAL

WARNING: WHEN REPAIRING STARTER MOTOR OR PERFORMING ANY MAINTENANCE IN THE AREA OF THE STARTER MOTOR, NOTE THE HEAVY GAUGE INPUT LEAD CONNECTED TO THE STARTER SOLENOID IS HOT AT ALL TIMES. MAKE SURE THE PROTECTIVE CAP IS INSTALLED OVER THE TERMINAL AND IS REPLACED AFTER REPAIR.

  1. Disconnect the battery ground cable.
2. Remove the ground strap bolt
3 Remove the nuts and lower the starter motor.
4 Remove the cap
  1. Remove the terminal nuts and remove the starter motor.
INSTALLATION
  1. Follow the removal procedure in reverse order.

Posted on Aug 01, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

3,0L Ford ranger 91 want shift into over drive.did before I pulled trans to replace rear main seal in Truck.please help


Overdrive is engaged with a torque convert clutch lockup. ATF travels through the splined shaft on the transmission to the torque converter. Check the seals on the converter and the trans.

Aug 25, 2015 | Ford Cars & Trucks

1 Answer

Truck is a 4x4 and a 88 Ford Ranger, when you turn the key, the starter will not engage. However, if you ratchet the clitch, sometimes the starter turns over, Is it mechanical or the computer and does...


I know on mine (88 ranger 4x4 manual transfer case and ******, 2.9 v6, short wheel base) it has what seems to me to be something similar to a nuetral safety switch. The starter will not even try to engage unless the clutch is in. You're kind of vague in your description. But if your issue is not getting it to turn over when in nuetral, and not pressing in the clutch I don't think anything is broken, that it is a safety feature from Ford

Jul 06, 2011 | 1988 Ford Ranger

1 Answer

Have 99 ford ranger 4.0 v6 4x4 automatic. the shifter will not budge when I try to shift gears. what could be the problem?


under the dash if you look, press the brake with your hand, you will see a button that the brake petal pushes against, that unlocks the shifter, either that switch needs replaced, or you linkage is froze up.

Nov 29, 2010 | 1999 Ford Ranger SuperCab

1 Answer

How do you get the oil pan ot of a 1990 ford ranger 4x4 4.0L


Hey, so i have a 1992 Ford Ranger V6 4.0L and i'm trying to figure out the same problem without going to a dealer and from what i have figured out you supposedly have to pull the engine out of the truck when it is a 4.0L.

Sep 16, 2010 | 1992 Ford Ranger

1 Answer

Lights flash off and on on dash and 4 wheel will not engage 1999 ford Ranger pickup .lights even flash off and on when not turned on going down the road.


according to the ranger station the 4x4 has a brain box on the passenger side under the dash and it is bad if it does this

Feb 21, 2010 | 1999 Ford Ranger SuperCab

3 Answers

2001 Ford Ranger V6 timing chain


Hello;
The Ford motors are pretty good. I had 280K on a 2.9 V-8 that only needed the oil changed every 3K. Unless you have fluctuatuation in the timing then you should be ok.
These engines use a chain rather than a belt and have excellent life.
Thanks;
Rich RPM Northwest

Jul 01, 2009 | 2001 Ford Ranger Regular Cab

1 Answer

Probleme with the 4x4 on my ranger 1999


have solenoid that engages 4x4 checked

May 13, 2009 | 1999 Ford Ranger SuperCab

2 Answers

1993 ford explorer - toublshooting fuse/electical problem


I believe the fuse for your starter is in the power distribution box, 93 explorer 4.0L 4X4. find diagram for this in Chilton Ford Ranger/Explorer/Mountaineer 1991-1999 Repair Manual 26688 page 6-43 Fig.88 Be aware that there are (4) figures for the 93 4.0L explorer and each shows a different part of the same engine wiring. See top right 'power distribution box' follow lines to the part of your engine you are concerned with, which fuse number, then look inside your engine, passenger fender, push down on the protective ?wall then pull the cover up, see your diagram and fuse numbers. The diagram for inside fuse box, page 6-31 fig.63 I hope this helps

Jul 05, 2008 | 1993 Ford Explorer Limited

Not finding what you are looking for?
1999 Ford Ranger SuperCab Logo

1,022 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...