Question about 2005 Mercury Mountaineer

1 Answer

How to remove the right rear door panel on a 2005 mountaineer

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 1,986 Answers

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: removing 97 mountaineer door panel

just let someone replace it for you , because by the time you do this and that , you won t have a panel left ..............

Posted on Feb 07, 2009

  • 14036 Answers

SOURCE: How to remove the right rear door panel on a 2005

you need a tool pry the panel from clips. you need a haynes manual to tell you where all your screws is located to move door panel.

Posted on Apr 24, 2009

  • 1986 Answers

SOURCE: rear door panel removal

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

  • 1986 Answers

SOURCE: Remove right rear door panel 2003 Buick LaSabre

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

  • 1 Answer

SOURCE: Remove the right rear door panel in a Mercury Sable

Removed two screws from the perimeter of the door, one in the back edge and the other under the bottom. Remove one screw from the handle cup where the window switch is located. Placed some tape around the edge of the handle cup for protection against scratches and pried the cup out with a small putty knife. It is hard, but will pop out. Next I taped the paint around the door panel and used a flat bar to reach behind the panel and had enough of a gap to see the orange tabs and pried each one to remove the panel completely. The panel does not need to be lifted up to removed, just pull it straight off the door. A few tabs may still be holding, but will pop off with a bit of pressure.

Posted on Oct 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Removal of rear door lift hatch interior plastic panel on a 2005 Dodge Grand Caravan to push out dent in metal door from the inside.


The rear door panel is secured to the door using screws and clips. The screws will be in the handle used to close the door and there may be plastic plugs in the handle hiding the screws. Once these screws are removed, the handle will come off. Look for any more screws along the panel. If there are more, they will be visible. Once the screws are removed, pull on the panel to release the clips that secure it to the door. These clips will require some force to release them and will make a snap/pop sound once released. You may have to put a screwdriver/wedge between the panel and door to start the process of releasing the clips

Jan 20, 2016 | 2005 Dodge Grand Caravan

2 Answers

Removing drivers side door panel ( inside panel )


Explorer/Mountaineer and 1993-99 Ranger
See Figures 1 and 2
  1. Open the window.
  2. Unscrew the door lock knob.
  3. On Explorer/Mountaineer, remove the 2 screws retaining the trim panel located above the door handle.
  4. On Ranger, remove the two screws in the armrest and remove it.
zjlimited_442.jpg

Fig. 1: Exploded view of the front door trim panel

zjlimited_443.jpg

Fig. 2: Exploded view of the Explorer and Mountaineer 4-door rear door trim panel

  1. If equipped with manual window crank handles, pull off the handle cover, then remove the attaching screw.
  2. Remove the trim cup behind (Explorer/Mountaineer) or around (Ranger) the door handle using a small prying tool. Retention nibs will flex for ease of removal.
  1. If equipped with power accessories, use the notch at the lower end of the plate and pry the plate off. Remove the plate from the trim panel and pull the wiring harness from behind the panel. Disconnect the harness from the switches.
  2. Remove any retaining screws uncovered by the removed trim pieces.
  3. Using a flat wood spatula, insert it carefully behind the panel and slide it along to find the push-pins. When you encounter a pin, pry the pin outward. Do this until all the pins are out. NEVER PULL ON THE PANEL TO REMOVE THE PINS!
  4. Lift slightly to disengage the panel from the flange at the top of the door
  1. Disconnect the door courtesy lamp and remove the panel completely. Replace any damaged or bent attaching clips.
  2. Installation is the reverse of removal.

Hope this helps (remember to rate this answer).

Jan 10, 2011 | 1998 Ford Explorer

1 Answer

Just bought a 2002 Mountaineer w/keyless entry. The problem is no one at the dealer knows the code. How can I reset it?


In the 2002 Mercury Mountaineer, especially with the 3rd row seat, remove the trim panels at the rear of the back door and at the tailgate on the passenger side. You will see two panels where the wall seat belt is located, remove the top panel first and then pull the lower panel out.Then pull the lower trim panel forward CAREFULLY. Towards the front (near the door opening) you will see a small black box (says Security Unit) On it in fairly small print will be the 5 digit code.
[ONE set of FIVE numbers and that is your CODE number.]

Nov 16, 2010 | 2002 Mercury Mountaineer

1 Answer

Not having any heat there is aclicking sound when i turn controls to heat


you have a A/C-Heat blend door actuator malfunction. This door switches from A/C vent to heater core vents via an actuator motor.Very Typical problem on Ford/Mercury/Lincolns vehicles. There are multiple actuators in this vehicle, some in the dash and some in the rear (only if equipped w/rear A/C-Heater. This will require pin pointing the exact fault, and may require lower dashboard or rear quarter panel interior trim (if rear A/C-Heater equipped) removal

Oct 24, 2010 | 2005 Mercury Mountaineer

2 Answers

How do i remove a door panel of my 2005 nissan sentra ?


If it is the rear door panel, you start by lifting, pulling upward, the door closer/arm rest.
Remove the electric window control and disconnect wire from switch.
Remove two hex/phillip head screws which are visible when you remove arm rest.
Remove a plastic screw on rear edge of door located about 6 inches below window glass.
Gently pry around edges of door panel to force plastic fasteners (approximately 6) out.

Oct 25, 2009 | 2005 Nissan Sentra

1 Answer

Need to remove door panel on 2007 mercury mountaineer


  1. Disconnect negative battery cabe
  2. Carefully detach the door handle bezel
  3. Pry out the front edge of the armrest switch control plate and disconnect the electrical connectors then remove the retaining screw from the opening
  4. Remove the lower trim panel retaining screws
  5. Once all the screws are removed grasp the trim panel at the switch opening and pull it up and out.Disconnect the power mirror electrical connector

Aug 10, 2009 | 2005 Mercury Mountaineer

1 Answer

How to remove the right rear door panel on a 2005 chrysler pacifica? A diagram would be helpful.


you need a tool pry the panel from clips. you need a haynes manual to tell you where all your screws is located to move door panel.

Apr 24, 2009 | 2005 Chrysler Pacifica

1 Answer

Removing 97 mountaineer door panel


just let someone replace it for you , because by the time you do this and that , you won t have a panel left ..............

Jan 21, 2009 | 1997 Mercury Mountaineer

Not finding what you are looking for?
2005 Mercury Mountaineer Logo

Related Topics:

230 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

fordexpert

Level 3 Expert

5470 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...