Question about 2007 Lexus ES 350

2 Answers

How to set the automatic garage door opener - 2007 Lexus ES 350

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 430 Answers

This is generally easy. Although you have not mentioned the brand, the system in the car and most cars is made by HOMELINK and they have a great website where you can go to find out how to program almost any car , etc with any garage door opener.

First , since the car is not new, hold button 1 and 3 on the car's overhead console continually for about 30 seconds. The lights will be on solid , then flash, then eventually go out. This erases any old codes. Then select your hanset position and a corresponding position on the cars pad. Lets say button 1. Hold your handheld remote to the overhead console and depress button 1 on both devices while watching the lights flash , fast then slow, then off.
Once done the car has received the signal and is ready to open the door.
On a door system with rolling codes there will also be a learn button ( Chamberlain, Liftmaster. Craftsman, etc.)on the drive unit in the garage,.This button is used to introduce a new device in "SAFE" mode.

Take a step stool , recah up and press the learn button . Then within 30 seconds push the console button in the car for 2 seconds and release. The openers lights will flash to acknowledge, then push the button in the car again for 2 seconds to test. Last step, retest your hand held to be sure it is still active as well. Post back to advise how you made out

Posted on Nov 09, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

No. It did not. I have a Genie system and it does not work. I dont have a rolling code either. Junk car, or junk opener, or just plain stupidity in programming the damn thing.

Posted on Jan 22, 2010

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: GARAGE DOOR OPENER

http://www.homelink.com/
This video is great.  My problem was that the light didn't go to fast blinking based on the directions for my vehicle.  After watching the video, I got the idea to move closer and it worked like a charm!

Posted on Jul 14, 2008

  • 1 Answer

SOURCE: how to set up for 2005 pacifica garage door opener

how about a real answer......

1. Press and hold the two outer HomeLink buttons, and
release only when the indicator light begins to flash (after
20 seconds). Do not hold the buttons for longer than 30
seconds and do not repeat step one to program a second
and/or third hand-held transmitter to the remaining two
HomeLink buttons.

2. Position the end of your hand-held transmitter 1-3
inches (3-8 cm) away from the HomeLink buttons while
keeping the indicator light in view.
3. Simultaneously press and hold both the HomeLink
button that you want to train and the hand-held transmitter
buttons. Do not release the buttons until step 4
has been completed.

4. The HomeLink indicator light will flash slowly and
then rapidly after HomeLink successfully receives the
frequency signal from the hand-held transmitter. Release
both buttons after the indicator light changes from the
slow to the rapid flash.
5. Press and hold the just trained HomeLink button and
observe the indicator light. If the indicator light stays on
constantly, programming is complete
and your device
should activate when the HomeLink button is pressed
and released.

Posted on Dec 27, 2009

  • 5 Answers

SOURCE: setting garage door opener

Most openers are programmed the same. You normally program the house garage opener to accept the new remote. Your garage opener will have a button to press to add in a new remote. Normally you press this and then press the remote in the car and hold until your lights on your opener flash or the garage door closes. (check your manual on your garage door opener)

Posted on Apr 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My rear automatic door on my 2008 gmc acadia will only work if I manually open it. when I do open it you can hear the motor for the door running but it will not open it or close it. I have to open it...


Drive chained is off, I have had to do many repairs were a automatic door would not open/close, each one is different, basically need to take apart and inspect?

Mar 04, 2015 | 2008 GMC Acadia

1 Answer

Genie garage door op


There is a set button on garage door opener look at manual that is in the garage hanging. to make car and door work together you will need both manuals

May 16, 2014 | Lincoln MKX Cars & Trucks

1 Answer

Garage Door Opener


there a botton inside the opener and a botton inside your garage opener push them both at same time it should link together

Dec 11, 2011 | 2002 Oldsmobile Silhouette

1 Answer

What are the three buttons for that are on the drivers side sun visor?


they make it possible for you to program your automatic garage door opener to open using them-'home link' the older ones (probably like yours)do not work with 'rolling code' door openers, but if you have an automatic door opener, you can try to program the controller to work with it.

Mar 10, 2011 | 1996 Chrysler Cirrus

1 Answer

Land Rover Discovery 1 1998 garage opener programming


press the two outter buttons for 10 sec. the press the the button on the door remove the same time you hold the button on the door opener. if this still does not work you must push the learn button on the door opener the is attacher to the door. the with in 30 sec push the button in the car thre times

Jul 14, 2009 | 1998 Land Rover Discovery

1 Answer

Need to program/link garage door opener with the one on the visor in the car


Depending on the name brand of the garage door opener, there is a button on it you press and you have about 30 seconds to set the button in the car to the signal. Read you car manual on how to set the visor opener, probably press and hold the button in after pressing the button on the garage door opener motor. Get someone to help you in the garage on a ladder. Mine is a Sears and this is how it works.

May 29, 2009 | 2006 Audi A4

1 Answer

Programing auto garage door opener


Sorry, the process is simple but too lengthy to post here.

Goto homelink.com

They make the system and have very complete instructions you can download.

PLEASE NOTE: MOST but not ALL Brands / models of opener will work with this system.

Apr 18, 2009 | 1999 Oldsmobile Bravada

1 Answer

Setting garage door opener


Most openers are programmed the same. You normally program the house garage opener to accept the new remote. Your garage opener will have a button to press to add in a new remote. Normally you press this and then press the remote in the car and hold until your lights on your opener flash or the garage door closes. (check your manual on your garage door opener)

Mar 27, 2009 | 2005 Chevrolet TrailBlazer

1 Answer

How can i program my garage door to open from my 01 jeep grand ch


Hold down the button on your garage door opener while pushing one of the 3 buttons on the overhead console in the Jeep. It will beep when confirmed.

Jan 05, 2009 | 2001 Jeep Grand Cherokee

1 Answer

2002 GMC ENVOY GARAGE DOOR OPENER


You have a quick fix item. There is a send code button on your garage door opener. You simply have to press that button, and within 5 secs, press and hold the button on the garage door opener (your car or other) until the opener rapidly blinks. The garage door and the opener will share info,,, and presto,, you can open by the remote opener. Take a peek at your garage door opener instructions. You can have up to three settings at one time... one for each button. I was asked if the buttons ever got the openers mixed up,, and the answer is absolutely not.

Jul 15, 2008 | 2002 GMC Envoy

Not finding what you are looking for?
2007 Lexus ES 350 Logo

2,914 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

75842 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

881 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...