Question about 1998 Lincoln Town Car

1 Answer

Need to know how to take it off to replace.

I need to know how to take off tail light to replace.thank you..

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Lincoln Master
  • 2,007 Answers

All bolts are in the trunk, behind the carpet. If it's just a bulb you're replacing, squeeze the nylon clip on the back, and turn it counter clock wise, and it'll come out.

Posted on Aug 01, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need instructions on how to replace a Ford Edge Rear Indicator Light. Thanks!


I was looking for the instructions for your tail light removal and came across a detailed description on how to access the tail lights. Here it is:-

http://www.paulstravelpictures.com/Ford-Edge-Tail-Light-Bulbs-Replacement-Guide/index.html

Apr 11, 2011 | Ford Edge Cars & Trucks

1 Answer

Do I replace a tail light from the inside of the truck or does the tail light pop out...just trying to make it to the bulb to replace. thanks 1986 Chevrolet Monte Carlo


i believe that there is fasteners inside the trunk that hold the tail light assembly to the car.i think about 6 that look like wing nuts and are black plastic that need to be removed to pull out the tail light assembly to replace the bulbs in the back of the lens assembly itself.

Apr 01, 2011 | Chevrolet Monte Carlo Cars & Trucks

1 Answer

Where to start looking for a short in a 1992 ford ranger. keeps blowing the fuse that runs the dash lights and the tail lights ..first it blew .i replaced .was fine till next night .turned on lights...


connector under the truck, near the trans
cannot remember specifics at this time but remember starting there every time one cam into the dealer with tail light issues and blown fuses

Jun 17, 2010 | 1992 Ford Ranger

1 Answer

No tail lights


You should have a fuse panel under you dash inside. This is where the fuses are located for lights. Don't know the exact location, but you can pull each fuse to see if it is bad. This won't hurt anything. It just keeps you from hunting down a diagram of where the fuse is located.

Apr 20, 2010 | 2008 Scion Xb

1 Answer

Drivers side rear blinker light needs replaced


Open the tail gate, and you will see on the side of the tail light housing two screws that you will need to unscrew in order to take the housing out. If it is the tail light ,that is on the actual gate, open the tail gate and remove the plastic bed liner there are few of screws that need to be removed. Hope this helps you fix it.

Apr 17, 2010 | 2003 Subaru Baja

1 Answer

Remeove rear combination tail light cover 2006 Nissan XTERRA


thode screws hold the lens or the light assembly? Allow for the whole tail light to come out and the bulb plug will be accessible. I never had the privilage. But how the lens fits will tell you. If the lens goes overthe edges, the whole unit comes out, lens is sealed. Good luck

Jun 03, 2009 | 2006 Nissan Xterra

1 Answer

Tail light out replaced both brake & tail lite bulbs nothing


It sounds like your brake light switch is out.  It's located on the brake pedal and is relatively easy and cheap to replace.  Let me know if you have any questions.  Thanks for rating my response and for using FixYa!

May 27, 2009 | 1997 Chrysler Town & Country

1 Answer

Tail light


there are 2 screws take them out get a putty knife andslightly put in between the tail light and bed jiggle it then pull firmly on light towards you chould come right out/Please rate my response thank you very much

Jan 27, 2009 | 1991 Nissan Pickup

Not finding what you are looking for?

Open Questions:

0 Answers

98 Lincoln TC,Cold starts fine ,runs good until warm, then shuts off. No codes,Cranks ok, have spark, PATS ok. No fuel pressure, cant hear fuel pump prime,New Fuel relay. jumped fuel pump - works. I do not hear fuel pump prime up, do not have fuel gauge, but pressing on valve in fuel rail- no pressurized fuel. Fuel regulator seems ok, not leaking / vacuum line dry as a bone. If I let it set for 15 min , it will start up again, but for a few minutes then dies out. If I let it set overnight it starts up perfectly and runs until operating temp is reached then stalls/stumbles, and shuts down. Vacuum is good while cranking, even with no start, Checked Inertia switch in trunk, it is not tripped. I have seen Ford TSB summaries' that mention issues like this , but I am not able to see to description. A point to add, the MAF sensor was cleaned, then I decided to replace it and did not make a difference. I do not have any stored codes, and the PATS is working fine, typical 2 second flash from and once key is inserted a 3 second steady light, then disappears. I have seen the TSB mentioning C103 Connector, it looks fine, I swapped out fuel pump relay with ac relay, still no difference.mention of wires around battery, do not know where to start. in dash service engine light and odometer is normal, seen other posts the say they only have lines, but mine is ok. the start of all of this , I washed engine with regular garden hose, ( not using pressure washer).also in the mean time, rear window defroster stopped working as well, can not say for same reason, but a mention.My problem started after washing engine. this is one of four Panther platform vehicles I owned with exact 4.6l w code engine, which I rinced down before. The only sensor I can think of is Oil pressure , or a corroded wire

Feb 27, 2017 | 1998 Lincoln Town Car

See all 1998 Lincoln Town Car Questions

1998 Lincoln Town Car Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

fordexpert

Level 3 Expert

5470 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...