Question about 2001 Jeep Grand Cherokee

1 Answer

Need to know know what parts I need to replace a axel

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 86 Answers

HI. ALL YOU NEED IS AN AXEL UNLESS YOU FIND SOMETHING THATS BAD WHEN YOU TAKE IT APART. GOOD LUCK. JIMBO

Posted on Aug 05, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1989 Subaru GL Wagon, told I need both axels replaced and ball joints as well as brakes replaced, for $500.00. Is that too much?


That whole deals sounds fishy. Brake job should be about $100 depending on parts. That part about needing to replace axle to replace ball joints doesn't sound right. I've been a diesel mechanic for 30 yrs and bought, drove and fixed used cars a bunch. Not that specific one, but plenty of them. Get another opinion.

Feb 25, 2016 | 1989 Subaru Gl Wagon

1 Answer

How Do I replace front axel seals


Now can you buy whole axel and change.

Oct 13, 2014 | 2005 Dodge Dakota Quad

2 Answers

Need to know how to remove front halfshaft on a 1998 chevy blazer


Google the exact steps...you'll be amazed what you find.

Apr 19, 2011 | Chevrolet Blazer Cars & Trucks

2 Answers

Passenger side at end of axle losse inside rotor is loose on bearing and flopping inside with wheel off will just a bearing fix this


most likely it will be just the bearing, unless someone has driven it this way for prolonged time in this case it might need other parts as well such as a new axel, or even a rotor. if it has been the case then the axel nut that holds the axel in the bearing has gotten so hot the chances of loosining it up will be verry slim and verry hard to remove, thus damaging the axel nut threads. if nit is this loose, I would expect to replace the bearing and the axel.

Dec 31, 2010 | 2001 Hyundai Accent

1 Answer

I was going to replace a wheel brake cylinder on my rear axel. I thought I could just pull off the hub to get to the brake assembly but there is a bolted on cap and screwed on plate on the end of the...


Some cars/trucks have the hub mounted with screws/bolts. You will have to remove them to get the hub off. You may need a rubber mallet to beat on the hub a little to get it to come off past the groove the brake pads may have made in the hub. After you get the hub off, take a picture of the brake components so you will know where everything goes once you start removing parts. Once you remove the springs, stuff will shift around and fall out on you so be careful and try to notice where everything goes as it is removed. If you run into problems during reassembly, you can always remove the hub on the other side to get pointers on where everything should go. Good luck.

Oct 11, 2010 | Dodge Ram 2500 Cars & Trucks

1 Answer

C/v axel replacement


you can do it. time consuming as with any repair at home.as long as you got repair manual & proper tools.if ur not sure go to autozone.com put in ur info .then you can view step by step instructions with pix under repair info.good luck!

May 23, 2009 | 1996 Isuzu Trooper

1 Answer

Exhaust replacement & Rear Brakes


I can't see a problem with the converter, but if your in one of the states that does emissions testing it might be a problem as it most likely would leak where its clamped. The best thing to do is get it all on and try to find someone to weld it for you. As far as axel seals, if there bolt in axels unbolt pull out and use the end of the axel to pop out the old seal, and just tap the new seal in carefuly. seals around $ 10.00. Break kleen will clean up break shoes and drumb. Need more help just ask.

Mar 04, 2009 | 1985 Ford F150

1 Answer

Replace rear axel bearing on 4x4 5.3 Litre gas engine


Loosen differential cover and let oil drain. Remove cover, remove U lock from axel. Pull axel out. Remove bearing seal then bearing. Install new bearing, seal and reinstall axel. Reinstall U lock and new cover gasket. Fill with 75-90wt gear oil. Now I know that sound pretty straight forward. But there are some things to remember. The U lock can be difficult to remove sometimes. The most important thing is the seal, you will need to make sure it gets seated correctly and not torn when installing axel.

Jul 12, 2008 | 2000 GMC New Sierra 1500

Not finding what you are looking for?
2001 Jeep Grand Cherokee Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...