Question about 1997 Isuzu Rodeo

3 Answers

How to replace front cv shafts on a 1997 isuzu rodeo ?

Posted by on

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

On the 99 rodeos u have to remove the drivers cv axcel first and slide the whole axcel assembly towards the drivers side to removes passenger side it sucks but les schawb wont do it they say its dealer only so either do it ur self or pay out the @$$

Posted on Nov 10, 2014

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 11,896 Answers

Remove tire, remove axle nut, pop ball joint off, remove clip, pull axle

For a more detailed instructions, go to autozone.com and register for free.
Now you will have full free online repair manual

Posted on Aug 01, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,596 Answers

Rejakwilson @ aol.com For Full Illistrations (PICTURES) PREPARATIONS:

  1. Jack up the vehicle and support it using jack stands.
  2. Remove the tire and wheel.
  3. Remove the drain bolt to drain differential oil.


NOTE:
  • During the work, be sure that the differential case is supported by the jack.
  • Remove the brake caliper fixing bolt and hang the caliper.
  • Remove the antilock brake system speed sensor. (If equipped with antilock brake system)
  1. Hub assembly (Disc, back plate and knuckle):
    1. Remove the locking hub.
    2. Disconnect the knuckle and the suspension arm.
  1. Steering link and arm assembly.
  2. Suspension crossmember.
  3. Propeller shaft.
  4. Protector.
  5. Breather Hose:
    1. Remove the hose clips.
    2. Disconnect breather hoses from front drive axle tube and disconnect housing.
  1. Vacuum Hose. Disconnect vacuum hose from actuator. Shift switch connector (7a).
  2. VSV Assembly. NOTE: Be sure not to remove hose and connector from VSV assembly.
  3. Mounting bolt and nut.
  4. Washer and spacer.
  5. Bolt. Remove the mounting bracket fixing bolt.
  6. Front axle case assembly and front drive shaft assembly (LH side). Lower the vehicle and disconnect the RH front drive shaft assembly, and then remove the front axle case assembly and front drive shaft assembly (LH).
  7. Front drive shaft assembly (RH).

Posted on Aug 01, 2009

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

daltonp
  • 361 Answers

SOURCE: 1997 isuzu rodeo front CV shafts ,how to separate

The axel should just snap in a good sharp pull should remove it.

Posted on Nov 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Isuzu rodeo troubleshooting


Sounds like a ball joint seeing that the cv joints were replaced, have you had it aligned?

May 07, 2014 | 1998 Isuzu Rodeo

1 Answer

Im replacin the cv joints on passanger side and driver side how do i get the axle out of the transmission casing is ther a key behind the plate with the 4 bolts? my truck is a 99 isuzu rodeo LS 4wd


remove inner cv boot, just on inside edge is circlip which holds inner bearing joint into outer housing remove circlip and separate joint outer housing does not come out of front diff unless you drop or remove whole front diff assembly
will have to remove whole stub axle hub assembly to remove drive shaft from outer wheel stub axle (hub) assembly

Apr 20, 2011 | 1999 Isuzu Rodeo

1 Answer

Removing front cv joints


Best thing to do is take the inner joint apart and put the new parts on the shaft sticking out of the housing. Save hours of trouble, I have seen many done like this.

Dec 12, 2010 | 1997 Isuzu Rodeo

1 Answer

1997 isuzu rodeo front CV shafts ,how to separate from pumpkin


The axel should just snap in a good sharp pull should remove it.

Nov 30, 2010 | 1997 Isuzu Rodeo

1 Answer

Replace cv shaft on 1996 isuzu rodeo. I have outer shaft free from hub, but how do you release the inner shaft? I see 4 bolts attached to the bell housing but not sure if I should remove them.


Yes the bolts will attatch to the bell housing. It sounds like you have the right idea. Pretty straight forward job. I find the easiest bolt to access, then spin the shaft by hand to the next one in N, then put in Park to remove if nessessary.
Try not to bend the CV joints too far when handling them, they are not designed for angles over 40 degrees or so. Make sure to torque all the bolts down to the specs.
Good Luck.

Mar 04, 2010 | 1996 Isuzu Rodeo

1 Answer

'93 Isuzu Rodeo, CV Joint replacement.


unbolt the tie rod end and the lower a arm and it should slide out of there

Jan 26, 2010 | 1999 Isuzu Rodeo

1 Answer

I have a 1999 isuzu 4wd rodeo 6 cylinder and was wondering if Need to install a new boot kit or if I need to replace the entire front left cv axle shaft. I had a tear in my rubber boot and noted some...


Do not try to get the cv axle out ot the axle housing. It is a major operation. Remove boot and disconnect the inner cv joint and save about five hours of time. The choice is yours ,boot or reman cv axle. You will need to take the reman. axle apart to install it though and some new clamps. Not a simple operation.

Sep 28, 2009 | 1997 Isuzu Rodeo

1 Answer

How to replace front cv shafts ?


remove inner cv boot, just on inside edge is circlip which holds inner bearing joint into outer housing remove circlip and separate joint outer housing does not come out of front diff unless you drop or remove whole front diff assembly
will have to remove whole stub axle hub assembly to remove drive shaft from outer wheel stub axle (hub) assembly

Aug 01, 2009 | 1997 Isuzu Rodeo

1 Answer

Cv joint removal


Get the replacement cv axle and remove inner boot and clip and bearings. Do the same on the old axle. Replace bearing clip, cv shaft and reassemble. Do not try to remove the part from inside the front axle unless you want to spend about six hours of time and money.

May 12, 2009 | 1999 Isuzu Rodeo

2 Answers

Having problem pulling cv axle


from the front? If so no there is no easy way to do so. I had to drop the differental and then remove the cv shaft.... but this was on a 1993 I would think its still the same...

Feb 09, 2009 | 2001 Isuzu Rodeo

Not finding what you are looking for?
1997 Isuzu Rodeo Logo

1,015 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14384 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...