Question about Audi A3

1 Answer

Its a 52 reg A3 5 door removal of drivers door card (panel)

Its a 52 reg A3 5 door and i would like to know how to remove the drivers door card as i can only see one screw under the door pull handle what takes the window switches off.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 173 Answers

You need to look Very closely, on the underside of the handles, for small, 'hidden' fixings to release the switch gear.
The card itself,is hooked onto the door.
So there aren't too many screws actually holding it all together.
Good luck with that.

Posted on Aug 01, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install power window cable


cable? (electric>?)
here is the page on motor;reg.
  1. Disconnect and isolate the battery negative cable.
  2. Remove the window regulator from the door.
    • Remove door trim panel.
    • Remove isolator.
    • Remove front door glass.
    • Loosen bolts attaching regulator to inner door panel.
    • Remove bolt attaching regulator to inner door panel.
      • Lift regulator upward to disengage bolts from door inner panel.
      • Disengage power window regulator harness connector, if equipped.
      • Remove regulator through access hole in door
    • Place the window regulator on a suitable work surface and remove the screws that secure the power window motor to the window regulator.
    • Remove the power window motor from the window regulator.

Jul 04, 2014 | 2000 Jeep Grand Cherokee

1 Answer

Install passenger window


most cars?
remove door cards, (the cover on inside of the door)
remove regulator bolts
remove reg. after detacting window base bracket.
remove, window .
some cars the upper trim can be removed, but that usually wrecks and costs 200 for a new set.
then pull window up past all missing seals.
if you remove the door card, you will see what needs to be done.
they pop off when pried, , start at bottom. (knobs first)

May 02, 2013 | 1995 Geo Prizm

1 Answer

1998 gmc serria drivers window stuck in the up position,, took the door panel off now their is another metal panel that the window motor and reg is mounted to. how do i lower the window and finish taking...


This is a pane to do, unbolt the plate, you will need to move the plate around and down to get to bolts at the bottom of the glass to remove the glass, with glass removed make sure the linkage to latch is disconnected and any wiring, then you will be able to remove the plate, hope this helps.

Aug 30, 2010 | 1998 GMC Sierra

2 Answers

Y reg 307 passenger door wont open sounds like all locks are working ane handels seem to be still ok inside and out but door just wont open


typical french car,it has a plastic clip that if someone slams the door it breaks and you need to remove the interior door panel/inner skin(plastic)to get to it (the clips on the door will break off.)the clip runs between the door handle and the operating mechanism.

Jul 27, 2010 | 2005 Peugeot 405

1 Answer

Audi a3 r reg remove inner door panel drivers side


On the inside trim, you can remove screws (these screws may be covered by filler pieces or may be visible, or they may require you pry a plastic piece off that covers the screws) that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls.

Oct 30, 2009 | 2005 Audi A3

1 Answer

How to replace the driver window regulator for a dodge grand caravan 2003?


remove door panel, a couple of screws, then pull up and panel comes off,uhook wire connections,now support window. remove 2 bolts holding glass to regulator and then unbolt reg from door unhook motor connection and pull out. good luck.

Oct 10, 2009 | 2003 Dodge Grand Caravan AWD

1 Answer

Remove a driver side door panel on a 2000 Toyota Limited 4 Runner


remove the screws that hold the inside door handle and clips behind the door panel

Jun 14, 2009 | 2000 Toyota Corolla

1 Answer

Rear passenger window does not go up or down


The window regulator (the track part) probably has failed. The motor and regulator might come together. It is easy to replace. Hardest part is getting the door panel off, which you've already done. Just unbolt glass from reg, slide up out of the way, tape glass up so it doesn't fall on your hands while your working with the reg. Unbolt reg from door and tilt down to remove from door. There should be an opening in the door to bring it out or you may have to remove a speaker. Just be careful working with the glass.

Oct 04, 2008 | 2005 Jeep Liberty

1 Answer

I need to replace the power window motor in a 1990 Accura


Ok, I'm assuming you verified that in deed the motor is faulty. You will need to remove the door inner trim panel switches, entry lighting and inner door handle will need to be unplugged/removed there should be a inner weather seal also this seal is important if you would like to keep the inner trim panel from rotting away so carefully remove it. Attached to the window motor is the regulator. The window is directely connected to reg. by two fastening nuts 10 mm. window stops at top of door as well remove. I mark there location when removing this makes adjust alot easier and most times no adjustment needed if marking is right once window is out regulator and motor can be removed I strong suggest that if possible to move the reg. and window motor in full up position to remove motor this is because the reg. has a spring assit to help raising window glass and is under tension to be wary of this fact Three screws attach motor to regulator these screws will in most cases be tight sometimes requiring " Impact Driver Tool" this is a hand used with a ball peen hammer once screws are out reassembliy time If this is your frist time with this type of repair I suggest help of assitant window glass will need to be very carefully handled.. good luck

Jul 14, 2008 | 1990 Acura Integra Hatchback

1 Answer

Install the regulator


what reg if its the window reg remove door trim,
remove speaker,
remove the three 12mm bolts holding the reg in,remove the two 10mm bolts holding the glass in,lift up glass pull out reg.
and repeat in opposite to reinstall.
please leave feedback.

Jul 01, 2008 | 1995 Suzuki Sidekick

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

297 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14379 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...