Question about 2008 Dodge Nitro

1 Answer

Change oil alarm in dodge nitro is flashing after oil change how can i reset

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 72 Answers

It is possibly flashing because there is still too little oil or too much oil.

Posted on Aug 01, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Check engine light on 2011 dodge nitro


Hey guys I have a 2011 Dodge Nitro 3.7 and today my engine light came on and it was running like I was on rumble strips. I floored it and it sputtered and ran terrible then the light started flashing then I cut it off tried to reset still the light came on. I put the scanner on it and it turned out to be the coil plug on the #3 cylinder. COIL PLUG. Hope this helps out GOD BLESS!

Sep 04, 2013 | 2011 Dodge Nitro

1 Answer

How to reset oil light on dodge nitro


This one is simple...

Insert key in ignition and turn to on position (do not start engine)
Press the accelerator Pedal fully to the floor and release 3 times back to back.
Immdeiatly cut key off and remove from switch.

This should do it without a problem,,
Hope this helps
ROger

Feb 08, 2012 | 2010 Dodge Nitro

2 Answers

Is thr a switch that lets the nito know that u had changed the oil


If you have the R/T with the onboard computer, you can reset the light through that. If not, there is a very simple reset sequence. 

Begin with the vehicle off. 
Turn the key to the ON position, but do not start the engine.
Press the accelerator pedal to the floor and release it three times.
Turn the key to the OFF position. 

Now if you turn the key on or start the engine, you should see that the light has reset itself, and will only come back on after 3000 miles, or if the ECU senses an oil problem. 

Aug 22, 2010 | 2009 Dodge Nitro

1 Answer

2008 dodge nitro change oil light how to turn off had oil changed did not go out


Directions are in the book, but you would put the key in and turn it all the way, just don't start engine. Pump gas pedal all the way to the floor 3 times slowly, but it has to be with 10 seconds. Turn key off and when you start again, oil changed chime and warning should not be on. If it is, try again.

May 21, 2010 | 2008 Dodge Nitro

2 Answers

Change oil alarm still flashing after i changed the oil twice


put the key in the ignition and turn it to the first click, acc. do not start the vehicle, pump the gas pedal 3 times all the way up and down, then turn the key off, after that start the vehicle that should reset the light and alarm. please rate thanks

Aug 19, 2009 | 2008 Dodge Nitro

2 Answers

Where is the oil filter on a 2007 dodge nitro v6


You can access the oil filter easily from underneath next to the front, driver-side wheel at the front of the engine. There is clear access to the filter there.

For more info on Dodge Nitro, visit the forum at
http://www.dodge-nitro.com/dodge-nitro/

Aug 08, 2009 | 2008 Dodge Nitro

1 Answer

Change oil alarm still flashing after i changed the oil twice


Try removing the Positive battary cable from the battery post.Wait a few minutes. Re-connect it and see if this helps.

Jul 31, 2009 | 2008 Dodge Nitro

1 Answer

Dodge nitro ''change oil'' light reset, how???


Turn the key on, engine off, slowly depress the accelerator pedal to the floor three times within ten seconds. Turn the key off. Turn the key on and start the vehicle. If it is still on repeat the process.

May 30, 2009 | 2008 Dodge Nitro

1 Answer

Steps on how to change oil filter on 2008 Dodge Nitro


unscrew the old filter, lube the rubber O ring seal of the new one with engine oil and install, tighten 3/4 of a turn from when it contacts sealing surface of engine.

Mar 05, 2009 | 2008 Dodge Nitro

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

249 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...