Question about Lincoln Cars & Trucks

1 Answer

2000 lincoln continental signal and hazard blinking lights not blinking

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Lincoln Master
  • 15,575 Answers

Do you know what a lighting control module is ?
Turn Signal and Hazard Lamps The turn signal system consists of:

  • turn signal miniature bulbs (13465)
  • lighting control module
  • multi-function switch (13K359)
  • indicator bulbs in the virtual image instrument cluster (10849)
  • circuit wiring and circuit protection
Turn signal system operates as follows:
  • The multi-function switch is protected by fuse junction panel Fuse 3 (10A). This fuse is hot in RUN.
  • Circuits 104 (LB/O) and 105 (R/W) connect lighting control module to the left and right turn signal switches of the multi-function switch.
  • Ground is provided to the lighting control module and the turn signal miniature bulbs through Circuit 57 (BK).
  • Turn signal functions are performed by double filament bulbs in lamp assemblies located next to the headlamps.
  • The turn/hazard function utilizes the second filament of the appropriate bulb(s).
  • With the multi-function switch in the right turn position, power is supplied to the RH front and rear turn signal miniature bulbs and the RH turn indicator in the instrument cluster.
  • With the multi-function switch in the left turn position, power is supplied to the LH front and rear turn signal miniature bulbs and the LH turn indicator in the instrument cluster.
  • Do you know what diagnostic trouble codes are ?
Section 17-01: Lighting, Exterior 1997 Continental Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 07/29/1996 Turn Signal Lamps/Hazard Warning Flasher Lamps
Inspection and Verification
  1. Verify the customer's concern by operating the turn signal/hazard flasher lamps to duplicate the condition.
  1. Inspect to determine if one of the following mechanical or electrical concerns apply:

    VISUAL INSPECTION CHART Mechanical Electrical
    • Damaged multi-function switch.
    • Circuitry open/shorted.
    • Fuse junction panel fuses:
      • 1 (10A)
      • 3 (10A)
      • 7 (15A)
      • 13 (15A)
      • 19 (10A)
      • 20 (10A)
      • 25 (10A)
      • 31 (15A)
    • Power distribution box Fuse 16 (20A)
    • Bulb open.
  1. If inspection reveals an obvious concern that is readily serviced, correct the concern before continuing with Inspection and Verification.
  1. If a concern remains after the inspection, connect the Rotunda New Generation Star (NGS) Tester 007-00500 or equivalent to the data link connector (DLC) located beneath the instrument panel to perform DATA LINK DIAGNOSTICS test. If the NGS responds with NO RESPONSE/NOT EQUIPPED for the lighting control module, GO to Pinpoint Test CA. If the DATA LINK DIAGNOSTICS test is passed for the lighting control module, retrieve continuous DTCs and execute Self Test Diagnostics for the lighting control module to retrieve current DTCs.
  1. If self test is passed and no DTCs are retrieved, go to the Symptom Chart to continue diagnostics.
  1. If DTCs are retrieved, go to the Lighting Control Module (LCM) Diagnostic Trouble Code (DTC) Index to continue diagnostics.
  1. If the lighting control module cannot be accessed by the NGS, go to Pinpoint Test CA.
Rotunda Service Bay Diagnostic System (SBDS®) 001-00001 may also be used to diagnose this system.
your best bet mite be to take it to a qualified repair shop. Unless you have a scan tool that can check for DTC'S an know how to use a wiring diagram an DMM - digital multi-meter to test electrical circuits .

Posted on Apr 20, 2018

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 1998 Lincoln Town Car

If your main brake lights are not working and the third light in the back window is working
it is the turn signal switch on the column cost about 150 to have replaced

Posted on Aug 30, 2008

chuck943
  • 783 Answers

SOURCE: 2000 lincoln continental stuck

Make sure you have brake lights.This is were the shifter solenoid gets it's signal from to get it out of gear.
One thing you can try is turn the igntion switch towards the run postion stopping just short of activating the electronics.Then try and move shifter to neutral then you can start it and out it into gear so you can drive it to get it fixed.

Posted on Mar 02, 2009

  • 3 Answers

SOURCE: 2000 lincoln continental door open

all fords/lincoln/mercury have a door ajar switch on all 4 door latches you can change just the switchs & some have a door conrtol module i have seen somw fords internal wiring & just pull the door ajar bulb out or just ignor it

Posted on Mar 02, 2009

MNfisherman
  • 11896 Answers

SOURCE: on a 2000 lincoln continental the electric door

lock mechanism is wearing out and the motor is not power full enough to push all 4 rods at one time

Posted on Jul 10, 2009

  • 1986 Answers

SOURCE: replace rear brake light bulb 1998 lincoln continental

pop the trunk and right behind where the lights are pull the carpet down and their will be of the following depending on the trim.

You will either see the light sockets themselves that you can twist and pull to change the bulb, or you will see the plastic nuts/screws that you can remove to remove the entire assembly in order to access the bulbs.

If it's your 3rd brake light, the screws to access the housing are located in the upper part of the trunk

Posted on Oct 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 Lincoln Continental was in for repairs and now my turn signals and break lights dont work. Im being told it's something to do with the anti theft system because the battery was unhooked. The...


I suspect there is a problem with the turn signal/ hazard switch. turn the turn signal on left or right, if it doesn't flash, grip the hazard button and gently wiggle it around, if the signals start flashing, replace the turn signal switch. The Brake lights are wired through the turn signal switch, if the 3rd brake light works, the brake switch is OK. I don't think it has anything to do with the anti theft system (at this time)

Sep 21, 2011 | 1999 Lincoln Continental

1 Answer

1996 lincoln continental: where is the hazard/turn signal flasher relay located?


the hazard flasher is a separate flasher from the signal flasher.they are located on the fuse panel under the dash on the drivers side.some are held in a clip to the wiring harness under the dash.you don`t say if one or the other is working if so then turn on the one that works and look for it and you will see what they look like and find the other and change it.

Mar 30, 2011 | 1996 Lincoln Continental

2 Answers

Where is the flasher relay located on my 97 continental? I have looked under the dash and no luck. The auto parts store does not even list a part number for a 97. At first the rt blinker stopped working...


The Lincoln Continental flasher is integrated into the "Multifunction light control module" part # 13c788. Cost junk yard around $50. There is no stand alone flasher relay as in the older or more senseably engineered and cheaper cars.

Hope helps.

Dec 20, 2010 | 1997 Lincoln Continental

2 Answers

My blinkers and hazard lights dont work on my 98 Lincoln Continental


Have you Checked the fuse ? And do you own a test light ? Regards, Lee

Aug 12, 2010 | 1998 Lincoln Continental

1 Answer

No turn signal indicator light and no hazard flashing light


1998 Lincoln Continental 4.6L SFI DOHC 8cyl

I suggest check your FLASHER; the flasher is located front seating area, driver side, under dash, mounted above kick panel.

Hope helps (remember rated this help).

Feb 11, 2010 | 1998 Lincoln Continental

1 Answer

I hav no signal lights or emergency lights at all


you will have to change your hazard light switch and put new one and should work.if my info was of any help please leave a comment,notee,vote.thankyou

Jul 15, 2009 | 1996 Lincoln Continental

1 Answer

2000 lincoln continental door open


all fords/lincoln/mercury have a door ajar switch on all 4 door latches you can change just the switchs & some have a door conrtol module i have seen somw fords internal wiring & just pull the door ajar bulb out or just ignor it

Mar 02, 2009 | 2000 Lincoln Continental

1 Answer

2000 lincoln continental stuck


Make sure you have brake lights.This is were the shifter solenoid gets it's signal from to get it out of gear.
One thing you can try is turn the igntion switch towards the run postion stopping just short of activating the electronics.Then try and move shifter to neutral then you can start it and out it into gear so you can drive it to get it fixed.

Mar 02, 2009 | 2000 Lincoln Continental

2 Answers

Right turn signal lamps


Sounds like the computer is telling you that you have a bulb out check all the bulbs and see if one is burnt out.

Jan 08, 2009 | 1998 Lincoln Continental

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

Marvin
Marvin

Level 3 Expert

84625 Answers

gerry bissi

Level 3 Expert

4387 Answers

fordexpert

Level 3 Expert

5692 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...