Question about 2000 Chevrolet Venture

1 Answer

Where can I find the bcm brain/chip in my 2000 chevy impala?

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 32 Answers

In the computor

Posted on Aug 01, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My 2006 chevy impala door locks do not operate

Do you know anything about body electronics , BCM - body control module ? The door lock switches are control inputs to the BCM .The BCM will energize relays in the I/P fuse block to lock or unlock the doors . Check out wiring diagrams here Enter your vehicle info. Year , make , model and engine size . Under system click on Body & Accessories . Then under subsystem click on power locks . Do the power windows work ? .There maybe codes stored in the BCM . your best bet mite be to take it to the dealer .

Apr 12, 2017 | 2006 Chevrolet Impala

1 Answer

2003 Chevy Impala 3.8Ltr, does this vehicle have a main electrical computer brain? If so, what is it called & where is it located? Dash msg lights on & off, no brake lights, turn signals, headlights...

sounds like you need to start by checking fuses. there are panels on the ends of your dash on both driver and passenger sides. there are also two fuse boxes under the hood that are essentially your main fuse block. there is a BCM...or body control module...but i would start with the fuses first

Aug 13, 2013 | 2003 Chevrolet Impala

1 Answer

Were is the body control module in my 2005 chevy impala

2001 impala not always starting. thinking BCM bad. hav reset but not always starts. Ideas?

Dec 19, 2012 | 2001 Chevrolet Impala

1 Answer

Is the BCM on a 2000 Chevy Blazer S-10 plug and play

I would say no. You have the resistor key for the ignition, right? The bcm is programmed to read that resistance or it will not enable the start relay.

Dec 17, 2017 | 2000 Chevrolet Blazer

1 Answer

Where is the (bcm) located in 2007 chevy impala

BCM is actually located above the kick panel under the dash mounted with plastic pull clips left side above e-brake.

May 21, 2012 | Chevrolet Impala Cars & Trucks

1 Answer

While driving Down the road sometimes the lights would turn off while switching from brights to dims and now we no longer have no dims at all just brights.

I had a similar problem with my 2002 chevy impala, it was the BCM Module, Costed about $680 to replace it from the dealership, the Dealership has a special tool to replace the old BCM because it has your car information and it has to be put on the new BCM.

Dec 04, 2011 | 2002 Chevrolet Impala

3 Answers

Cabin lights 2001 impala problem shuting off

Hello JJ, the problem areas to check would be:

1. headlight and panel dimmer switch.
2. interior door lamp control module
3. keyless entry module
4. door lock control module
5. door jam switches.
6. wiring problems.

Most of the time, it is the door switch on the drivers side, that is the problem.
I hope this information is helpful.


Oct 14, 2011 | 2001 Chevrolet Impala

1 Answer

I have a Chevy Impala 2002 and I have to change the BCM. How can I program the new BCM. What I need to reprogram the new BCM.

A new BCM HAS to be programmed by a shop with a Tech II programmer.

Good luck, i hope this helps.

Jun 28, 2011 | 2002 Chevrolet Impala

1 Answer

I bought a 2000 chevy impala and i do not have the manual and i change the battey and the radio block please tell me how can i unluck it

You must take your car to the dealer. The factory scan tool can pull a code from the BCM and they have to call GM directly to get the radio code. After that has been done, make sure the code is written somewhere in case that happens again. They will probably charge you 1 hour labor which will be anywhere from $70-$120.

Jun 19, 2011 | 2000 Chevrolet Impala

1 Answer

2000 chevy impala

neutral safety switch..:) good luck

Aug 26, 2008 | 2000 Chevrolet Impala

Not finding what you are looking for?
2000 Chevrolet Venture Logo

Related Topics:

179 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

80531 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides