Question about 1995 Kia Sportage

Open Question

Instructions for replacing the starter on a 1995 kia sportage, and the best tool for removing the bolts from the bell housing

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

DIY 2005 Kia Sedona EX starter replacement


1 Disconnect negative battery cable
2 unplug wire connector
3 disconnect positive wire (the bigger wire) usually has a nut or bolt to hold it on

4 their will be 2 bolts to hold the starter in place that need to be removed. they will most likely pass through the trans bell housing and thread into the starter motor.

5 starter should pull easily off the car

to reassemble reverse the steps

Aug 05, 2016 | 2005 Kia Sedona

2 Answers

H0w to change thermostat housing on 1995 Kia sportage


  • Drain the coolant and dispose of properly,
    Remove the clamp on the upper radiator hose where it connects to the elbow on the engine block.
    Remove the hose from this connection
    Remove the 3 bolts on the elbow that the hose was on, where they connect to the engine block.
  • Remove the elbow, this is the housing.
  • Clean the surfaces that the housing covered using a razor blade.
  • Replace the thermostat with a new one.
  • Replace the gasket
  • Torque the bolts for the housing to the right torque.
  • Replace the hose and clamp.
  • Fill the Radiator with NEW coolant. Leave cap off
  • Start the engine and squeeze the upper radiator hose several times to remove air.
  • Watch for the level in the radiator to drop
  • Add coolant as needed, till the level is even with the inside lip on the radiator neck WHEN THE ENGINE IS HOT.
  • Put new radiator cap on.
  • Stop engine and drain the reservoir tank for old coolant.
  • Replace the coolant with new coolant.

Feb 02, 2016 | 1995 Kia Sportage

1 Answer

Where is the starter located on my 97 kia sportage 4x4?


for a left hand drive diesel engine powered Kia sportage, it is at the right rear and bottom portion of the engind, right below the brake pedals. it is attached to the bell housing.

Apr 30, 2015 | 1997 Kia Sportage

1 Answer

How do I change the starter?


Hi,

here is for the Removal & Installation
1. Disconnect negative battery cable. Remove two upper bolts from intake manifold bracket. Raise and support vehicle. Raise and support vehicle. On M/T, remove clutch slave cylinder from side of clutch housing and push it aside.
2. On all models remove lower intake manifold bracket bolts and bracket. Remove two upper starter bolts and a lower bolt. Pull starter from clutch (M/T)or converter (A/T) housing and prop in place. From above, disconnect starter solenoid "S" and "B" terminal connectors. From below, push transmission harness aside and remove starter.
3. To install, reverse removal proceedure. Rotate starter to provide proper clearance. Torque all nuts and bolts to specifications.


Good luck!

Aug 06, 2010 | 1999 Kia Sportage

1 Answer

Need to know how to replace a 98 Kia sportage starter


Remove positive terminal from battery From under passenger side above front drive shaft remove intake bracket 14mm 1 bolt on bottom of intake 2 bolts at bottom of bracket remove bracket. remove 3 14mm bolts from starter one is on top and kind hard to get at (3/8 swivel is required) lower starter care full it will fall on you head if you let it remove electrical connections re install.

Aug 01, 2010 | 1998 Kia Sportage

1 Answer

Starter for kia sportage 2000


  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:

    Negative battery cable Intake manifold bracket upper bolts Clutch release cylinder and move it aside, if equipped Intake manifold bracket lower bolts and remove the bracket Starter from the clutch, manual transmissions only Starter from the torque converter, automatic transmissions only Starter electrical connectors Move the transmission wire harness aside Starter


    0900c152801b0603.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Exploded view of the starter

To install:
  1. Install or connect the following:

    Starter to the engine well Starter electrical connectors Lower intake manifold bracket and install the upper bolts Starter into position. When aligned properly torque the bolts to 40 ft. lbs. (54 Nm). Torque the intake manifold bracket bolts to 40 ft. lbs. (54 Nm). Properly position the clutch release cylinder, if equipped. Torque the bolts to 40 ft. lbs. (54 Nm). Torque the intake manifold bracket upper bolts to 40 ft. lbs. (54 Nm). Negative battery cable

Jun 28, 2009 | 2000 Kia Sportage

1 Answer

My starter needs to be replace. I'm more the willing to do the work myself, but I need to know if anyone else as done this before and how difficult is this?


Not a difficult job but you have to crawl around under the car. First thing to do is disconnect the battery. Now you need to get the car up high enough to work under. I like ramps but jack stands are go too. Never work under a car with only a jack holding it up. Chuck the tires and apply the emergency brake as well as putting the car in park, you get the idea. Now look for the starter at the rear of the engine way down low by the fly wheel. Notice that there are wires going to the forward end of the starter you need to remove them remembering where they go for the assembly of the new starter. Look at the rear of the starter where it attaches to the bell housing. Here you will see some large bolts attaching the starter flange to the bell hosing. Remove the lower bolt first and than the top. The starter will fall out in your hands. Just revers the steps for assemble

May 12, 2009 | 2005 Kia Sportage

2 Answers

Removal of starter for a 2000 Kia Sportage


YOU HAVE TO DO IT FROM THE BOTTOM THERE IS 1 12mm BOLT AND 1 NUT AND IT SHOULD COME OUT

Jan 28, 2009 | 2000 Kia Sportage

1 Answer

1998 kia sportage, how to replace the starter?


1. you have to remove the possitive on the battery.
2. lift the truck on the passenger side. (remember to use jack stands for security)
3. remove the wires going to the starter. (there should be 2 wires.)
a) a thick wire, thats the possitive.
b) a thin wire thats the starter signal from ignition switch.
4.remove the bolts holding the starter, you should see them they are the only ones touching the starter base.
5.you can sheck if yours is good at anu(advance discount auto parts).
6.do the same steps from four to one to install the new starter.

Jan 11, 2009 | 1998 Kia Sportage

1 Answer

2000 Kia Sportage


yes it is very easy just remove the air intake duct located on the radiator (2 10mm bolts) this exsposes the thermostat housing it has 3 10mm bolt remove those and the top of the housing the the thermostat. clean off old gasket material, then replace the thermostat and gasket and reassemble the housing and air intake duct.

Dec 15, 2008 | 2000 Kia Sportage

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...