Question about 2004 Cadillac SRX

Open Question

How do you remove the front bumper of a 04 cadillac srx in order to replace the headlight turn signal bulbs? The wheel well cover and cover beneath the bumper has been removed.

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

hdsoft
  • 80 Answers

SOURCE: headlight

Well according to my mitchell manuel you don't have to.here is the procedure.
1. open the hood.
2.Remove the push-pin retainer's that secure the top of the upper facia and grill assembly to the upper tie bar to allow the upper facia and grill assembly to flex forward.
3. remove ther bolt and push-pin retainer that secures the top of the headlight assembly to the upper tie bar.
4. Gently pull the upper facia and grill assembly forward to access the bolt on the inboard side of the headlight assembly
5. Pull the headlamp assembly straight out to disengage the the snap in retainer at the lower outboard back surface of the assembly. Turn the assembly so that the inboard assembly clears the front facia.
6. pull the assembly out and away from the veh.From there you'll be able to access bulbs.
be careful not to touch the bulb with fingers or oil in skin will blow bulb.
Good luck.

Posted on Aug 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change front turn signal bulb on 2008 SRX Cadillac


Nope don't need to drop the whole light assembly. I just took the wheel and inner cover off, then the 6 torx screws that hold the light hosing together , replaced the turn signal bulb and good to go!!

Mar 04, 2013 | 2004 Cadillac SRX

Tip

Change the front turn signal bulb on Cadillac SRX


I have found a short cut for changing the front turn signal bulb
  1. Remove the inner fender well cover and then you can remove the light assemble from underneth and replace the bulb.
  2. The cover is attached with a bunch of push on body clips, pry the button up with a screwdriver and pull out fastner.
  3. Then there are two screws holding the light assembly on the bottom and inner side, it clips into the bumper on the outter side. From there it's pretty simple.
  4. FYI the GE replacement cross reference is wrong it's a Sylvania 3757A LL bulb.

on Dec 02, 2009 | Cadillac SRX Cars & Trucks

1 Answer

Change turn signal bulb 2008 srx


Front turn signal bulb replacement 2008 SRX . Jack up car & block . Remove front wheel & front half of the wheel house assemble. There are about 7 plastic pull rivets that have to be removed . Pull out the wheel house . Remove turn signal & driving light cover held on by 6 # T10 torx screws . Twist out socket & replace bulb # 3757NAK . Should take about 45 min.

Mar 26, 2012 | 2006 Cadillac SRX

1 Answer

How to change a front blinker bulb on 2007 cadillac srx?


There might be a way to sneak the bulb out, but most likely the bumper cover will have to be removed it is a stupid design that gives you no room to work.

Mar 26, 2011 | 2007 Cadillac SRX

1 Answer

2006 Cadillac SRX- how to replace front directional light bulbs without dismantalling the whole front bumper cover?


Just remove the air filter housing and the inner right fender plastic pins enough to flex it out of the way...... then you can remove the six torx screws and remove the bulb cover........change the bulb.
spray a little WD40 in the bulb socket first.

Feb 20, 2011 | Cadillac SRX Cars & Trucks

1 Answer

How do u change the front signal bulbs on SRX 2004 with out taking the whole car apart???


Remove the bottom plastic cover along the front grills by pulling the push pins which hold them in place. You can slide the cover out . Remove the plastic cover inside the wheel which is also held by push pins.

When both the covers are out you ca use an 9/32'' wrench to remove the two bolts which hold the whole lamp assembly.You then need a torx driver to remove the six torx screws in the light assembly and you can replace the bulb.

Jan 04, 2011 | 2004 Cadillac SRX

1 Answer

Need to replace front turn signal bulb on a 2004 Cadillac SRX


need to remove front wheel and panel from the inside.
almost the entire wheel cover need to come off

Aug 04, 2010 | 2004 Cadillac SRX

3 Answers

I need to change the left front turn signal bulb on a 2006 Cadillac SRX? Looks difficult. Paul LeMaster


hi Paul

Should be able to open the hood remove plastic headlight cover & pull pins (2) on light assembly whole light assembly will pull out then replace turn signal.

Good luck.

Dec 02, 2009 | 2006 Cadillac SRX

3 Answers

Headlight


Well according to my mitchell manuel you don't have to.here is the procedure.
1. open the hood.
2.Remove the push-pin retainer's that secure the top of the upper facia and grill assembly to the upper tie bar to allow the upper facia and grill assembly to flex forward.
3. remove ther bolt and push-pin retainer that secures the top of the headlight assembly to the upper tie bar.
4. Gently pull the upper facia and grill assembly forward to access the bolt on the inboard side of the headlight assembly
5. Pull the headlamp assembly straight out to disengage the the snap in retainer at the lower outboard back surface of the assembly. Turn the assembly so that the inboard assembly clears the front facia.
6. pull the assembly out and away from the veh.From there you'll be able to access bulbs.
be careful not to touch the bulb with fingers or oil in skin will blow bulb.
Good luck.

Aug 19, 2009 | 2004 Cadillac SRX

2 Answers

Replacing front turn signal bulb on 2006 Cadillac SRX


You must take the front wheel off, then remove the inner front fender panels (2), they are fastened with plastic pushbuttons. this exposses the light housings for the turn and fog lambs. This takes about an hour, but saves you alot of money.

Nov 12, 2008 | 2006 Cadillac SRX

Not finding what you are looking for?
2004 Cadillac SRX Logo

Related Topics:

208 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...