Question about 2008 Dodge Nitro

1 Answer

Change oil alarm still flashing after i changed the oil twice

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

Try removing the Positive battary cable from the battery post.Wait a few minutes. Re-connect it and see if this helps.

Posted on Jul 31, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change oil in 2001 gmc Sierra


This may help good luck

Reset the Oil Change Display
Instructions
1
Insert the ignition key into the ignition and turn it to the "Run" position.
2
Push the accelerator pedal all the way down to the floor and release it three times within 5 seconds.
3
Look to see if the "Oil Change" light is flashing. It will flash twice to confirm that the system has been reset. If it does not do this, start over with Step 1.
Tips & Warnings
Repeat the steps above if the oil change light stays on for 5 continuous seconds. This means that the system was not reset.

Jun 15, 2013 | Cars & Trucks

1 Answer

2005 Chevrolet Avalanche -


I would ask Firestone what they did.

Jun 08, 2017 | 2002 Chevrolet Avalanche

1 Answer

How to reset(clear) alarm "Change Oil soon." ?


This work at 2001, but you could try it:
To reset the "CHANGE OIL" light, turn the ignition switch to the run position with the engine off. Fully depress and release the accelerator pedal three times within 5 seconds. The light will flash twice and go out.

Hope this helps and just keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer. Thank you for using FixYa.

Jose.

Oct 20, 2011 | 2003 Buick Century

1 Answer

How to turn change oil light


iI you mean 'how to turn change oil light off" go to fuse panel. Open drivers door there is a panel cover on the side of dash board, remove cover there is a red RESET button that resets oil pressure and tire pressure. Turn the ignition key to the on position but don't start the car. Now press and release the reset button the change oil light should start to flash, now press and hold the reset button until you hear chimming hold until chimming stops then release, the change oil light should go off. If you need to reset tire pressure press reset button twice, the first push will make the change oil light flash the second press will make the tire pressure light flash then hold untill chimming stops, light should go out . Hope this helps.

Sep 30, 2010 | 2000 Pontiac Grand Am GT

2 Answers

Change oil alarm still flashing after i changed the oil twice


put the key in the ignition and turn it to the first click, acc. do not start the vehicle, pump the gas pedal 3 times all the way up and down, then turn the key off, after that start the vehicle that should reset the light and alarm. please rate thanks

Aug 19, 2009 | 2008 Dodge Nitro

1 Answer

Change oil alarm in dodge nitro is flashing after oil change how can i reset


It is possibly flashing because there is still too little oil or too much oil.

Aug 01, 2009 | 2008 Dodge Nitro

2 Answers

Change oil light.


Turn the ignition to the "ON" position. with the engine NOT running. With the ignition in the "ON" position press the gas pedal down to the floor 3 times within 5 seconds. The light should flash twice. If it doesn't you need to try resetting it again.

Jan 26, 2009 | 1997 Chevrolet Lumina

3 Answers

How do I reset the "Oil Change Warning Indication" on colorado


if you have a owners manual read it. try coloradofans.com website and search the forums. i think johnny5846 is right if you don't have a DIC (driver info center). i believe you use the DIC(tripodometer). i don't know the sequence off hand, you can also you can change your lock settings and alarm settings, etc. with the DIC.

Jan 13, 2009 | 2006 Chevrolet Colorado

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...