Question about 1993 Nissan Pathfinder

1 Answer

Alarm problems(alarm wont activate,1995 factory system,red light not on on center console,no power to light,checked fuse,it was ok,traced wired to relay,how do you check relay?

Posted by on

  • spiderman042 Aug 01, 2009

    checked relay it works,getting power to box under drivers seat,no power to red light,or switch.i even pushed the reset in the bo,is there more relays or other boxes or fuses in the system?

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 40 Answers

Relays tipically have a diagram on them depicting which terminals are the switch and which are the signal try using jumper wires to the sensor terminals and listen for a click.

Posted on Aug 01, 2009

  • Chuck McFadden Aug 06, 2009

    That button on the boxunder the seat is for progrming the remotes not areset button that box is probably bad that is the most common problem with those systems.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an Acura MDX 2003 and can't disable the factory security alarm... I don't have a remote


If it's a cheap aftermarket alarm, check for a red wire coming off the hot side of your battery with an inline fuse. If it's not, try to locate the alarm "computer" under the driver's side dash or nearby your fuse panel. You'll find a black box with a wiring diagram glued to the side, normally strapped to a wiring harness or other fixed element. If this is the type of alarm you have, you'll need to trace each wire coming from the alarm computer and unclip each fastener that's clipped to your vehicle's factory wiring. The trouble with these types of alarms is that they can get power from a number of sources (stereo, interior lights, etc.). Good luck with this one!

Oct 05, 2012 | 2003 Acura MDX

2 Answers

I replaced the ignition switch in my 1995 ford ranger now the alarm won't stop


95 Ford Ranger Auto Alarm Wiring Diagram.

You need to re-check your ignition wiring. Here is the wiring for the alarm.

Battery Constant 12v+ Positive Wire (+): Yellow
Battery Constant 12v+ Positive Wire Location: Ignition Switch Harness

Starter Positive Wire (+): Red/Light Blue
Starter Positive Wire Location: Ignition Switch Harness

Ignition Positive Wire (+): Light Green/Purple
Ignition Positive Wire Location: Ignition Switch Harness

Second Ignition Positive Wire (+): Black/Light Green
Second Ignition Positive Wire Location: Ignition Switch Harness

Accessory Positive Wire (+): Gray/Yellow
Accessory Positive Wire Location: Ignition Switch Harness

Parking Light Positive Wire (+): White/Black Or Brown
Parking Light Positive Wire Location: At Headlight Switch Or Low In Drivers Kick Panel

Power Door Lock Negative Wire (-): Pink/Yellow (Type B)
Power Door Lock Negative Wire Location: In Either Kick Panel

Power Door Unlock Negative Wire (-): Pink/Light Green (Type B)
Power Door Unlock Negative Wire Location: In Either Kick Panel

Door Trigger Positive Wire (+): Black/Light Blue
Door Trigger Positive Wire Location: In Drivers Kick Panel

Domelight Supervision Wire: Use Door Trigger (Requires Relay)
Domelight Supervision Wire Location: N/A

Horn Negative Wire (-): Yellow/Light Green
Horn Negative Wire Location: At Steering Column Harness

Tachometer Wire Negative Wire (-): Any Wire With A Tan Stripe Or A Yellow Stripe
Tachometer Wire Negative Wire Location: At Ignition Coil

Brake Light Positive Wire (+): Light Green
Brake Light Positive Wire Location: At Switch Above Brake Pedal

Factory Alarm Disarm Wire (-): Dark Green/Purple
Factory Alarm Disarm Wire Location: Low In Drivers Kick Panel

Factory Anti-Theft System: N/A
Factory Anti-Theft System Location: N/A

Nov 16, 2011 | 1995 Ford Ranger Supercab

1 Answer

I have a Disco 200 V8 model. Came back from a trip and next morning, wont start. By passed alarm system with key code. No luck. Checked all wires. Launch 410 diagnostic indicate that permanent power loss...


Have a 99 disco....I had to take the gear selection control box, underneath the center consol. There isa switch that came loose that interfaces with the brake and ignition to start the car. Also there is a selenoid in the box that could go bad. also could be a bad brake switch. Try pushing the gear shift foward in park while cranking, if it cranks then the gear selection switch is bad. The problem is between the key switch and the starter....trace it down. Also you can buy cheap a LR repair disc.

Mar 15, 2011 | 2000 Land Rover Discovery

2 Answers

How to disarm or reset an alarm system for a 1996 Jeep Cherokee?


Hope this helps:- Factory Disarm Purple/Yellow (-) Driver's Kick Panel Black Connector at ECM -slice into this wire, & wire it to ground, this disables the alarm.
Cavity/Fuse Diagram (1996 Grand Cherokee, passenger side kick plate to find, Owner's Manual pgs 205-206): 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

Row 1: 1-6 (left to right) Row 2: 7-12 Row 3: 13-18 Row 4: 19-22
1996 Jeep Grand Cherokee Fuse Panel (Passenger Side kick panel) Reply

CAVITY FUSE DESCRIPTION 1 -10 amp (RED) Radio 2 -15 amp (Lt Blue) Cigarette Lighter 3 -10 amp (RED) Rear Washer Switch, Body Controller 4 -10 amp (RED) Airbag 5 -10 amp (RED) Lamp Out Module, Overdrive Switch, OBD II 6 -15 amp (Lt Blue) Vehicle Information Center/Graphic Display Module Park & Side Lamps, Overhead Console Lighted Visor, Automatic Dimming Mirror 7 -20 amp (Yellow) Body Amp, Cluster, Body Controller 8 -20 amp (Yellow) Rear Wiper Motor, Flipper Glass Solenoid, Cargo Lamp, Trailer Tow 9 -15 amp (Lt Blue) Brake Switch 10- 10 amp (RED) Rear Window Defroster 11 -10 amp (RED) ABS Module 12 -10 amp (RED) Heater-Ventilation-A/C Control & Recirculation Motor 13 -15 amp (Lt Blue) Hazard Switch, Turn Signal Switch 14 -15 amp (Lt Blue) Spare 15 -15 amp (Lt Blue) Spare 16 -10 amp (RED) Right & Left Courtesy Lamp, Glove Box Lamp, Halo Lamp Cargo Lamp, Underhood Lamp, Dome/Read Lamp Right & Left Visor, Automatic Dimming Mirror 17 -15 amp (Lt Blue) Radio Illumination, Tail Lamp, Graphic Display Module, Park & Side Lamps, Headlamp Switch, Body Controller 18 -20 amp (Yellow) Spare 19 -15 amp (Lt Blue) Passing Light 20 -15 amp (Lt Blue) Radio, Heater-Ventilation-A/C, Vehicle Information Center 21 -15 amp (Lt Blue) Power Outlet 22 -10 amp (Blue) Airbag Module -------------------------------------------------------------------------------------
1996 Jeep Grand Cherokee Alarm, Remote Starter, Keyless Entry Wiring Information Constant 12V+ Pink/Black Ignition Switch Harness Starter Yellow Ignition Switch Harness Ignition Dark Blue/Gray Ignition Switch Harness Ignition 2 Red/Black Ignition Switch Harness (for AC) Accessory Black/Orange Ignition Switch Harness Tach Gray/White Coil Brake Switch White/Tan Brake Switch Trunk Pin n/a Works with Dome Light Parking Lights Blue/Red (+) Left of Steering Column or Light Switch Head Lamp Tan/Black Light Switch Factory Disarm Purple/Yellow (-) Driver's Kick Panel Black Connector at ECM -slice into this wire, & wire it to ground, this disables the alarm. Door Trigger Yellow (-) Driver's Kick Panel see notes Door Lock 5/Wire in Driver's Inside Driver's Door Orange/Purple Lock Pink/Black Unlock Door Unlock and Passenger's Doors Inside Passenger's Door Black/White L Pink/Black Unlock Horn Wire Gray/Orange (-) Steering Column Windows Up LF=Light Blue, RF=Brown/White, LR=Blue/White, RR=Gray/Black Doors Windows Down LF=White, RF=Purple/White, LR=Red/Black, RR=Green/White
• Cruise Control Information • Stereo Information • View all Jeep Vehicles

Dec 18, 2010 | 1996 Jeep Grand Cherokee

3 Answers

I need to disable my alarm on a 1997 bmw 528i.


Now im not sure since the manual says your model has the same alarm system as the 328i and on the 328i you can remove the module to disable by doing the following. you can unplug the control module. It is located under the glove box. Climb under the dash on the passenger side and remove a few screws on the trim panel under the glove box. Theres a black control module with a green connector. There should be a lock tab on the connector. press the lock tab and pull out the connector. The alarm should now be disabled. But if it has the special transponder key this may not work.
But if the only reason you want to disable it is because of the motion sensor setting of the alarm for no reason there is a solution for this. To disable the motion sensor, hit the lock button to arm, then hit lock button again within four seconds to disable motion sensor. Red light on rearview mirror should flash four times, then pause, then start flashing on regular intervals. this is most likely the reason if your having the issue where the alarm goes off every 20 minutes.
If you want to completely remove it below is a wiring diagram taken from the manual for you alarm system.
this is from the manual its the alarm wiring diagram.
Battery Constant 12v Positive Wire ( ): Red/White or RedBattery Constant 12v Positive Wire Location: Ignition Switch Harness
Starter Positive Wire ( ): Black/Yellow or Black
Starter Positive Wire Location: Ignition Switch Harness
Ignition Positive Wire ( ): Green
Ignition Positive Wire Location: Ignition Switch Harness
Second Ignition Positive Wire ( ): Purple/White or Purple
Second Ignition Positive Wire Location: Ignition Switch Harness
Parking Light Positive Wire ( ): Gray/Purple and Gray/Yellow. Use Both Wires. This vehicle has a dual parking light system that will require 2 extra relays.
Parking Light Positive Wire Location: At Headlight Switch
Power Door Lock Positive Wire ( ): White/Red
Power Door Lock Positive Wire Location: At Factory Alarm Plug. The alarm plug is a black 12 pin plug located just behind the glove box.
Power Door Unlock Positive Wire ( ): Blue/Red
Power Door Unlock Positive Wire Location: At Factory Alarm Plug. The alarm plug is a black 12 pin plug located just behind the glove box.
Door Trigger Negative Wire (-): Brown/Gray
Door Trigger Negative Wire Location: At Factory Alarm Plug. The alarm plug is a black 12 pin plug located just behind the glove box.
Domelight Supervision Wire: Turns On With Unlock
Domelight Supervision Wire Location: N/A
Horn Negative Wire (-): Brown/Red or Brown/Yellow
Horn Negative Wire Location: At Steering Column Harness
Tachometer Wire Negative Wire (-): Black
Tachometer Wire Negative Wire Location: At Instrument Cluster
Brake Light Positive Wire ( ): Blue/Red or Green/Red
Brake Light Positive Wire Location: At Switch Above Brake Pedal
Factory Alarm Disarm Wire (-): Disarms With Factory Remote Only. Factory Alarm Disarm Wire Location: N/A
Factory Anti-Theft System: Transponder Anti-Theft System, Requires Bypass And Extra Ignition Key. The 1997 model year vehicle may require a bypass module and an extra ignition key, if vehicle is equipped with a special key from BMW.
Factory Anti-Theft System Location: Transponder At Ignition Switch Tumbler
if you require further assistance please let me know and i will help assist you from there. Thanks, Midwest-Tek

Aug 27, 2010 | 1997 BMW 328

2 Answers

2004 Nissan Quest - alarm Waking the neighbors


If it's a cheap aftermarket alarm, check for a red wire coming off the hot side of your battery with an inline fuse. If it's not, try to locate the alarm "computer" under the driver's side dash or nearby your fuse panel. You'll find a black box with a wiring diagram glued to the side, normally strapped to a wiring harness or other fixed element. If this is the type of alarm you have, you'll need to trace each wire coming from the alarm computer and unclip each fastener that's clipped to your vehicle's factory wiring. The trouble with these types of alarms is that they tie in and get power from a number of sources (stereo, interior lights, etc.), so you'll have to trace and unclip 8-12 wires to fully disengage. Good luck!

Jun 12, 2009 | 2004 Nissan Quest

2 Answers

Can you disable car alarm in 1991 Acura Legend by


If it's a cheap aftermarket alarm, check for a red wire coming off the hot side of your battery with an inline fuse. If it's not, try to locate the alarm "computer" under the driver's side dash or nearby your fuse panel. You'll find a black box with a wiring diagram glued to the side, normally strapped to a wiring harness or other fixed element. If this is the type of alarm you have, you'll need to trace each wire coming from the alarm computer and unclip each fastener that's clipped to your vehicle's factory wiring. The trouble with these types of alarms is that they can get power from a number of sources (stereo, interior lights, etc.). Good luck with this one!

Jun 12, 2009 | 1991 Acura Integra Hatchback

1 Answer

Car alarm stopped working.. Car wont start


the jetta has a faulty alarm system from the factory i have been working on one in my shop. the alarm moddule is inside the dash behind the light switch and has a 10 pin connector and a 6 pin connector. this can be bypassed if you disconnect both connectors and jump the two large wire on the 6 pin connectors, these wires operate your starter. the car will start and run but your alarm will no longer be active. the door locks and everthing else will still work. the only issue i am having is the factory radio isn't working because it is controlled by the alarm. but worse case scenario i can use an aftermarket radio if need be.

Feb 20, 2009 | 1994 Volkswagen Jetta

1 Answer

1995 camry wagon cigarette lighter not working


start with a test light and check for power at the center of the cigarette lighter socket. If power is good, then check for ground at side of lighter socket.
If no power, run wire from power wire of lighter to power wire of stereo, thus tapping the power directly and bothering to trace out where the open int he circuit may be.

Jan 25, 2009 | 1995 Toyota Camry

Not finding what you are looking for?
1993 Nissan Pathfinder Logo

165 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...