Question about Ford Mustang

Open Question

1991 mustang chime is very low and the electric trunc release don't work

Posted by on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How does one disconnect the warning buzzer?

Is it a buzzer or chime? There is a chime module under the dash that can be unplugged. Put your ear down low to find it and unplug it

May 10, 2015 | 2002 Ford Mustang

1 Answer

Why dont my fuel injectors pulsate on my 1991 ford mustang lx 5.0

Get a cheap set of noid lights and check for electrical pulse. If there is none, test your crank positioning sensor and the wires to it. If that don't work, try testing the distributor's electronic module.

Jan 15, 2013 | 1991 Ford Mustang

1 Answer

My tail lights and dash lights are not working on my 1991 Oldsmobile 88


Nov 18, 2011 | 1991 Oldsmobile Eighty Eight

1 Answer

How do I program an additional remote for my 2003 Durango

  • You must have a programmed FOB to program another at home with my instructions below. If you don't have programmed one then you must get the first one programmed at the dealer.

  1. Press LOCK button 5 times at 2 second intervals to re-synchronize remote.
  2. Insert key into the ignition switch.
  3. Turn ignition to the run (no start.)
  4. Wait for ignition chimes to stop.
  5. Using the working remote, press and hold the UNLOCK button on the remote for 4 to 10
  6. seconds.
  7. Within the specified 4 to 10 seconds, continue to hold the UNLOCK button and then press the PANIC button ( on the programmed remote ) for 1 second and release both buttons. A chime will sound to indicate that the remote programming mode has been entered ( allow 3 seconds for chime to sound ).
  8. Within 30 seconds of the chime, press and release the LOCK and UNLOCK buttons simultaneously then press and release just the UNLOCK button on the same remote.
  9. A chime will sound indicating the remote has been programmed. Press and release the LOCK and UNLOCK buttons simultaneously and then press the UNLOCK button on each new remote you wish to program at this time. Locks will cycle after each additional remote is programmed.
  10. Turn the ignition OFF and remove key.
  11. Try your remote.
  • Hope this helps.

Oct 23, 2011 | 2003 Dodge Durango

1 Answer

My signal lights and brake lights on my 91' Ford mustang stopped working. Does anyone have a owners manual?

Try checking You've checked your fuses already, correct? You can also pick up the correct Haynes or Chiltons manuals not only from your local Autozone or Pep Boys, but also many libraries carry these manuals as well.

Sep 13, 2011 | 1991 Ford Mustang

1 Answer

What would make heat and air blower motor only run slow on every speed switch no matter low or high 1991 ford mustang

If not the switch, you need to check vacuum lines near the firewall inside the engine compartment and under the dash. Just in case. I had problems with mine blowing only through the defrost because of a broke vacuum line. Good luck

Aug 14, 2011 | 1991 Ford Mustang

1 Answer

My 1991 ford mustang runs great but shuts off and my car has a few electric problems could that be the case?

You could have your ignition switch coming apart, this was a common problem on these cars. Dont mistake the ignition switch under the column for the ignition key cylinder

Apr 25, 2011 | 1991 Ford Mustang

2 Answers

How do you stop / turn off an 89 Mustang chime / buzzer?

If You Are Talking About The Door Chime There Are Two Ways To Do It One Is To Simply Unplug the Chime Two Is To Remove The Steering Columm cover and Unplug the black wire that is going to the side of the key switch I would Recommend This Method Because Unpluging The Chime Its Self Will Disable the Headlight on Switch off Warning As Well Removing The wire From Switch on column will disable key in switch door open only

Aug 17, 2009 | 1989 Ford Mustang

2 Answers

Chime Moduel

just plug it in

Jul 19, 2008 | 1998 Saturn SL

1 Answer

Car slipping at 35 MPH

are you sure it's slipping and not just missing, i'd check my electrical(plugs, wires, coil pack, etc.) sorry the new trans did'nt fix it i feel your pain.

Jul 06, 2008 | 1991 Ford Mustang

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers


Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides