Question about 2003 Ford Mustang

1 Answer

How many prongs are need for the 2003 v6 mustang on the fan motor. Just installed a new one and it shows 3 males but the female only has two at the wireharness

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,627 Answers

Your motor only need one power and one ground to work,the resister takes care of the speeds so this must be an universal motor and should still work.

Posted on Jul 31, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Put a 1996 mustang v6 motor into a 1995 mustang that had a v6 now I can't get any fire


There should be a distributor module screwed to the side distributor, Make sure it did not get damaged or try putting the original one on the motor you just installed. There is special tool for the screws , It cost about $12.00 the d module itself cost about $60.00, I hope this helps and that it fixes your problem. Michael

Feb 13, 2013 | Cars & Trucks

2 Answers

I have a 2002 v6 mustang. I installed a used 2002 v6 engine 3 weeks ago because my spark plug threads tore on my original. NOW i have 4 cyclinders misfireing, tranny shifts late or after i let off the...


its a well known cause that if the motor is running really bad the tranny will **** or act bad your gonna have to find the problem with the miss firing cyclinders and fix it doing this make fix your tranny problems you can clear most computer codes by unhooking the battery for about 10 min and then start it and see if the engine light comes back on that will give you a new set of codes you will have to have them read and fix what they are.

Jan 02, 2011 | 2003 Ford Mustang

2 Answers

I need a radiator cooling fan motor for a 2004 jeep gand cherokee laredo v6. I am only find ing motors with 2 prongs if that is the correct word but the one that is on the car is 3. How can I find one with...


funny, dealing w/ same problome today...Driving w/ heater on while 115 in Arizona is no fun.......DEALERS ARE NEVER THE SOLUTION FOR JEEPS!!!!!! $80...ebay make sure 3 prong...also 4th bolt on fan sucks here's a how to do..... http://www.jeepforum.com/forum/f310/04-wj-special-edition-overheating-1027069/
Also don't cut hole underneath headlight on 04....relays are in box...do a jump from plug to battery!!

Aug 18, 2010 | 2004 Jeep Grand Cherokee

1 Answer

Can I glue a plastic fan shroud on a 2003 mustang v6. It cracked and is making a noise when it is on.


try super glue and see if this works, if not get a used shroud from a wrecking yard.

Aug 08, 2010 | 2003 Ford Mustang

1 Answer

My coolin fan for my engine wont run? how do i fix it? 98 ford mustang gt


okay heres what causes not to kick in,
1 a bad motor
2 bad tempeture sensor
3 bad/defected fuse or relay.
check the fuses and your fan relay first. swap them around to test is every thing well then test the motor dirtectly, if its fine and works, then tempeture sensor on the engine. remove the harness and put a jumper wire on the prongs and what it kick the fan in. have the ign on with engine off for this. if it works replace the sensor.
hope this help you.

send mr your comments thansk

Aug 02, 2010 | 1998 Ford Mustang

2 Answers

Need to replace the coolant fan,,,My husband wants to do it himself..Has anyone tried this ??? I have a 2003 Turbo Pt Cruiser


its very easy. The fan is usually held in place with 3 or 4 small screws. The has a wiring connector you have to unplug. You may want to check and see if the problem is actually a bad fan motor. It could just as easily be the temp sensor... I would disconnect the wiring harness and put 12 volts onto the fan to verify the fan is bad... Good luck

Mar 29, 2010 | 2003 Chrysler PT Cruiser

1 Answer

Want to replace the radiator on my 1997 ford thunderbird


Radiator Aluminum Core, Crossflow — 3.8L (Base) and 4.6L Engines
Removal
  1. Drain engine cooling system as described. Disconnect upper radiator hose (8260) and lower radiator hose (8286) and radiator overflow hose (8075) from the radiator (8005). Disconnect the transmission oil cooler inlet and outlet lines from the radiator.
  1. Remove cooling fan motor,fan blade (8600) and fan shroud (8146) assembly as described.
  1. Remove radiator upper bracket retaining bolts and remove bracket. Lift radiator from vehicle.
Installation
  1. Position the radiator into the vehicle. Install upper brackets and tighten bolts securely.
  1. Connect the transmission oil cooler lines to the transmission oil cooler fittings.
  1. Install cooling fan motor, fan blade and fan shroud assembly as described.
Engine Cooling Fan Motor, Fan Blade and Fan Shroud Assembly, Electrical Removal
  1. Disconnect (pull apart) the male-female cooling fan motor wiring connector at the side of the fan shroud (8146). Remove the male terminal connector retaining clip from the fan shroud mounting tab.
  1. Remove two fan shroud upper retaining bolts at the radiator tanks.
  1. Lift cooling fan motor/fan blade (8600)/fan shroud assembly past radiator (8005), disengaging fan shroud from two lower retaining clips.
Installation
  1. Follow removal procedure in reverse order.
  1. Tighten fan shroud retaining bolts to 5.2-7.2 Nm (46-63 lb-in).

  2. 10e2638.gif
    8d231fe.gif HOPE THIS HELPS.

    Oct 30, 2009 | 1997 Ford Thunderbird LX

    1 Answer

    Will a 5.0 mustang v8 fit into a 2003 ford mustang v6....


    It will fit but you will need to move the mounts.

    Jun 23, 2009 | 2003 Ford Mustang

    Not finding what you are looking for?
    2003 Ford Mustang Logo

    Related Topics:

    60 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    75005 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    fordexpert

    Level 3 Expert

    5470 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...