Question about 2004 Buick Rendezvous

1 Answer

What tools to change brakes on 2004 Rendezvous

What tools to change front brakes on 2004 Rendezvous

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 65 Answers

2 CALIPER BOLTS EITHER A REGULAR WRENCH OR 3/8 ALLEN WRENCH. MEDIUM SIZE C-CLAMP TO PUSH IN THE CYLINDER ON THE CALIPER , AND HIGH TEMP BRAKE GREASE TO PUT ON CALIPER BOLTS WHEN RETIGHTENING. HOPE THIS HELPS CRAIG.
HERES A LINK TO LOOK AT I FOUND TOO!!

http://www.2carpros.com/how_to/how_to_replace_brakes.htm

Posted on Aug 28, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What tools do i need to change all the brakes on a 2007 buick rendezvous


Besides regular hand tools and socket sets, the first thing you will see are the front caliper retaining bolts or screws. GM cars often used large hex key fittings to loosen those, but expect anything on the caliper bolts, a lot of variation between years and models.
Your very best tool is a repair manual for the rendezvous, with step by step instructions. They cost about 26-30 dollars.

Jun 09, 2015 | 2007 Buick Rendezvous

1 Answer

Need to know which brake lines from the proportion box run to the front and back brakes on a Buick Rendezvous 2004


You can use a low voltage tracker. Connect to end at brake assembly and test at box on top.

Jan 05, 2015 | Buick Cars & Trucks

1 Answer

I'm replacing the shift solenoid in my 2004 Buick Rendezvous but I can't find any diagrams showing the location or how to change it out. Can you please help?


WHen you refer to the shift solenoid, are you meaning the solenoid that locks and unlocks the shift lever? If so, before you change this, check if your brake lights are working! A common fault for this solenoid to not work is either a blown fuse or failed brake light switch- the solenoid is activated by you pushing the brake pedal which sends its signal from the switch!

I hope this helps? Good luck!

Nov 11, 2013 | 2004 Buick Rendezvous

1 Answer

I've had my brakes and my barrings replaced but


I would start by checking for brake system codes. A parts store like Autozone should be able to do this for you.

Apr 01, 2012 | 2004 Buick Rendezvous

1 Answer

I have no brake pedal after replacing the pads on my 2004 Buick Rendezvous AWD


you may have air in the system. Start by pumping the brakes

Aug 13, 2009 | 2004 Buick Rendezvous

1 Answer

Anti lock light came on


You have a serious brake problem, most likely the front brakes are metal to metal, have it inspected ASAP, many brake shops and tire stores do this for free.

Apr 07, 2009 | 2004 Buick Rendezvous

3 Answers

Buick rendevousz headaches


I own the 2002 Buick Rendezvous CX and I've encountered the same problems listed here. The ABS / Traction Control Lamp stays on and was throwing a code for the left wheel speed sensor as well as an anti-lock brake code (both in the wheel bearing hub assembly). I replaced the left and right front wheel hub assembly yet this did not eliminate the abs codes. 
Ultimately, I traced this problem to a break in the wire that leads to the left hub assembly. Although the sensor was properly connected, the wire (which is encased in a plastic housing) was broken. This is the wiring which leads from the abs wiring harness under the hood down to the left wheel abs sensor. 
I would suggest that you simply remove the left wheel and inspect the wire that leads to the abs sensor (there is only one wire on each wheel). Mine literally fell apart when I removed the plastic housing around the wire. I spliced the wire together and put it back in the plastic housing. After this, my abs codes disappeared and my anti-lock brakes began working again!
This is a simple fix that many people spend $1000 + on by replacing the hub assembly which does not fix the problem.

Aug 20, 2008 | 2002 Buick Rendezvous

Not finding what you are looking for?
2004 Buick Rendezvous Logo

427 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...