Question about 2000 Toyota Camry

Open Question

Doesthe 2000 4speed Camry wagpn have a fan belt or is it electonic

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What type of fan belt goes on the2000 camry 4speed wago I was told it didn't need a fan belt but there was one before


most likely it needs a serpentine belt , not fan belt many newer cars have electric fans . check with a local auto supply store as to required belt.

Mar 27, 2018 | Cars & Trucks

1 Answer

Engine over heating


are you using a universal fan or engine fan?if you are using a universal fan then check the wiring there on it but if its the engine fan check your fan belt because it runs with the stearing pump

Oct 23, 2012 | 1993 Toyota Camry V6

1 Answer

My 2003 v6 camry recently overheated. Both alternator belt and 2nd belt recently replaced. No evidence of losing coolant. No change in oil appearance. Replaced coolant reservoir and let idle to...


both fans do not turn on at the same time. one fan is for the AC condensor and the other is for the radiator. A/C turns on one fan, Radiator temp switch turns on the other one. If you have never replaced the thermostat, or done a radiator flush/refill, you should do one now.

Aug 06, 2011 | 2003 Toyota Camry

1 Answer

Where is the knock sensor located? 2000 Toyota camry 4cyl


remove the intake manifold ,remove radiator ,remove radiator intake and outake housing, remove fan ,remove all belts: power steering, alternator and if you have a/c, remove harmonic balancer ,remove timing belt covers, remove timing belt remove intake housinng once you have remove all the above, your freaken engine will look naked, you can see the location of the knock sensor is locate in the engine valley

Jan 11, 2010 | 2000 Toyota Camry

1 Answer

Motor skipping problem on 2000 camry 4 cyl


CHeck ISC motor and clean it, along with the trottle body.

Sep 09, 2009 | 2000 Toyota Camry

1 Answer

I dont have a diagram to run serpentine belt to a toyota camry 03


Hi

Replacing Serpentine belt on a Toyota camry 2003—


Step 1--Examine the belt placement of your Toyota Camry fan belt so that you will remember how to put it back once you have removed it. Refer to the vehicle owner's manual for further information. Locate the pivot bolt on the front passenger side of the engine. Loosen the pivot bolt with a socket wrench.


Step 2--Loosen the adjustment locking bolt that is just below the tensioner pulley with a socket wrench, and then loosen the tensioner pulley to allow the belt to move free.


Step 3--Check the belt for any signs of cracking or irregular wear, so you can fix any problems that may exist with the pulleys. Remove the fan belt from the pulleys on the engine and take it out of the engine compartment.


Step 4--Wrap the new fan belt around each of the pulleys the same way it came out. When you have the belt in place, tighten the tensioner pulley with a socket wrench.


Step 5--Tighten the adjustment locking bolt and the pivot bolt with a socket wrench, and then look over the engine to check that everything is back in place.


Step 6--Turn the vehicle engine on and watch it for a few minutes to verify that everything is operating properly, then turn the engine off.


Please refer to these links for serpentine belt diagrams—

Serpentine belt on a Toyota camry Link 1

Serpentine belt on a Toyota camry Link 2

Please do accept the solution and revert for further assistance.

Thanks
Rylee

Jul 13, 2009 | 2003 Toyota Camry

1 Answer

Installation of a timing belt that loosened during removal of alternator for '05 Toyota Camry LE


Your timing belt has nothing to do with the alternator. You must mean your fan belt do you? The serpentine belt that you loosened to change the alternator? There should be a directional sticker under your hood somewhere, to show you how to put it back on. If not, just put ribs to ribs, and flats to flats, and work your way around.

Jul 03, 2009 | 2006 Toyota Camry

1 Answer

Timing belt needs to be replaced on a 4 cylinder 1993 toyota camry


hi..The belt is accessed by removing the fan guard, fan
and heater hoses.Then remove the belt covers.The lower
cover will require you to remove the belt drive.once removed
you can remove the old belt and reinstall it.
try this out..
thank u..
kindly rate my response..

Jun 09, 2009 | 1993 Toyota Camry V6

Not finding what you are looking for?
2000 Toyota Camry Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

Marvin
Marvin

Level 3 Expert

85020 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...