Question about 2004 Nissan Murano

1 Answer

2004 murano has throttle position sensor fault, chk eng lit. When I r/r the sensor, do I need to reprogram the ECU. If so how??? thks.. Rich

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,776 Answers

All that needs to be done is to replace the faulty TPS. There should be no need to do anything to the ECU. Hope this helps and best wishes.

Posted on Jul 31, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the position of throttle sensor of murano 2004 model


The throttle position sensor is incorporated into the electronic throttle control motor located on the side of the throttle bore where the air hose from the air filter box meets the throttle assembly

Dec 29, 2015 | Cars & Trucks

2 Answers

Car not taking the gas,code p2122 and p2127


check your aps sensor,accelarator position sensor if its bad and make sure all connector and wire from this sensor to ecu is good,.

Mar 09, 2015 | 2004 Kia Amanti

1 Answer

2004 Hyundai sonata eng code PL121, a throttle position sensor, but the throttle position sensor tests out good. What else could it be?


Code 121 is for a problem with the circuit for the sensor.
The computer is getting a signal that is out of range, too low or too high.
If you know for a fact the sensor is ok, you may have to check the circuit back to the computer. You would also need a scanner to read the sensor signal.

Jan 18, 2013 | Hyundai Motor 2004 Sonata

1 Answer

My 04 Kia Sorento has two faults, the throttle position sensor and the automatic transmission temp. sensor running together. This causes the automatic transmission to run through the gears and be in 5th by...


well if it has a 'service bullitin' then the manafacturar would know--hook it up to a tech ll which runs a data stream for solution cause it can get complicated--trans may need to be reprogramed or a module is bad etc

Apr 04, 2011 | 2004 Kia Sorento

2 Answers

97 CV - Chk Eng light on - something about oxygen sensor??? BUT - in cold weather - has little to no PWOWER in accellorating - UNLESS I allow the engine to "warm-up" for a while?>???


if the oxygen sensor is bad it will either not send or send the wrong signal to the ecu making the engine think it is running rich on fuel so the ecu cuts back the fuel supply

Jan 10, 2011 | 1997 Ford Crown Victoria

1 Answer

Error code 1680


Chevrolet OBD Fault Codes
DTC P1680 - Driver 5 (ECU malfunction)

This is any internal ECU problem (ECU = ECM = PCM device); check other details HERE; keep in mind that its possible that you have to reprogramm the ECU.

Here is a bulletin for this problem.Subject: Service Engine Soon Light On, P1680 (Reprogram or Replace PCM)

Models:
2004 Buick Rainier
2004 Chevrolet Trailblazer
2004 GMC Envoy
2004 Oldsmobile Bravada with 4.2L Engine (VIN S - RPO LL8)

Some customers may comment on the Service Engine Soon Light coming on. Upon investigation, the technician may find a P1680 diagnostic trouble code Check the resistance of the accelerator pedal position sensors using the procedure in the appropriate Service Information for DTC P1680.

If the resistance of the accelerator pedal position sensor is within the specifications shown in the Service Information and the vehicle was built prior to the following VIN breakpoints, then reprogram the PCM with the latest calibration.

If the resistance of the accelerator pedal position sensor is within the specifications shown in the Service Information and the vehicle was built after the following VIN breakpoints, then replace the PCM. If the resistance of the accelerator pedal position sensor is outside the specifications shown in the Service Information, then continue with the diagnostics for DTC P1680.

VIN Breakpoints
• Vehicles built at Oklahoma City Assembly Plant - 46192755
• Vehicles built at Moraine Assembly Plant - 42315833

Hope this help

Aug 03, 2010 | 2004 Chevrolet TrailBlazer

2 Answers

Jaguar xj6 4.0 1990. showing fault code fuel 14, fail 14. what does this code mean ?


2 airflow sensor out of operating range 3 coolant temp sensor out of operating range 4 oxy sensor indicates full rich 5 throttle potentiometer/airflow sensor... (low throttle pot signal with high airflow sensor signal) 6 throttle pot/airflow sensor...... (high throttle pot signal with low airflow sensor signal) 7 throttle pot...idle fuel adjustment failure(idle speed??) 8 intake air temp sensor...open or shorted circuit to sensor 11 Throttle pot at idle: Throttle pot idle trim out of normal range 12 Airflow meter: MAF signal out of range 14 Coolant thermistor: Resistance out of range or static during engine warm up 16 Air thermistor: Resistance out of range 17 Throttle pot: Out of range 18 Throttle pot/Airflow: Low throttle pot signal at high airflow 19 Throttle pot/Airflow: High throttle pot signal at low airflow 22 Fuel pump drive: ECU output to fuel pump relay 23 Fuel supply: Engine running too rich 24 Ignition Drive: ECU output to ignition Amp 26 Air leak: Engine running too lean 29 ECU self check 33 Injector Drive: ECU output to injectors 34 Injector: Looks for Injector dribble 37 EGR Drive: ECU output to EGR switching valve 39 EGR check sensor: EGR not working (normally pipe blocked) 44 Lambda (O2) sensor: Poor mixture control rich or weak (or misfire) 46 Idle speed Control valve: ECU output to Coil AB 47 Idle speed Control valve: ECU output to Coil CD 48 Idle Speed Control Valve: Stepper motor grossly out of position 66 Air pump: ECU output to air pump relay 68 Road speed sensor: Seen speed < 5km/h at high engine airflow 69 Drive/Neutral switch: Seen cranking in "D" or high airflow in "N" 89 Purge Valve drive: ECU output to purge valve
this is all I could find

Nov 09, 2009 | 1990 Jaguar XJ6

Not finding what you are looking for?
2004 Nissan Murano Logo

Related Topics:

964 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...