Question about 2002 Dodge Intrepid

Open Question

2002 chrysler intrepid, when accelerating, the car won't go, then after a few minutes she jumps and is fine again, i've had sensors replaced, coils replaced, still acting up, please help.

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Abs light on


Check the thickness of thr break pads, if they are thinner repalce them. if the pads are thick innaf then check sensors and sensor wiring after all the checks and replacment, reset electrical by removing +ve terminal of the battary for few minutes the fasten it and check. If the probleme arries again consult a pro..

Apr 03, 2014 | 2002 Chrysler PT Cruiser

1 Answer

Acura Legend 86 wont start after initially running fine


fuel pump going out and it will not run at all
coil problem will starteasy but fail after running for a while
fuel pump relay again it is running after starting and if the relay is no good , it will not pump fuel
try having the fault codes read first then have the faulty sensor replaced

May 13, 2017 | 1986 Acura Legend

1 Answer

Chrysler 300M p1391 code misfires when hot.


From research Chrysler is having a lot of this same problem. If it were another vehicle I would say it's either ignition module or pickup coils going bad. Some vehicles have had problems with wires to pickup coils (Hall effect coils) getting hot and shorting due bad wire insulation. One cause is oil or dirt getting on pickup coils, cam position sensor, also if cam is worn and moving any that will affect the gap between sensor and cam. You didn't say how many miles were on the car.

Apr 30, 2017 | 1999 Chrysler 300M

1 Answer

Why does my 1998 sebring idle fine but sputter badly under load.


Does it use spark plug wires or individual ignition coils for the each plug?. My 98 intrepid uses coils and occasionally I have to change them out cause it would start to miss when normal temperature was achieved. If it uses wires, try replacing them, along with the spark plugs.

Jun 21, 2012 | 1998 Chrysler Sebring

1 Answer

My 2000 Chrysler Sebring stops running. After a few minutes it will start again and run fine. This situation just started happenning a few months ago and is increasing in frequency


is the check engine light on??
i've done a few that had no light/codes.the most common problems are crank or cam sensor failures. really need to check when car stalls.
replacing crank sensor 6 mths ago & car has'nt had a problem. if you search these sensor on the sebring you'll find alot of info.

Jul 12, 2011 | 2000 Chrysler Sebring

2 Answers

What is wrong with my explorer if it cranks but won't go? I can crank it and when going down the highway it won't accel I can push the accelerator all the way down and it won't accelerate....


check plug wires and coil all spark in all plugs should be blue spark no orange spark if any orange replace coil i have a 2003 explorer so i know if that dont sove anything try a crankshaft postion sensor and or cam postion sensor as they tell cars ecu when to fire spark and what cylider to fire it to lmk what happens we can go from there


if it helps i would love a thumb up review

May 08, 2011 | 2002 Ford Explorer

2 Answers

Car hesitation


sounds like the coil pack is failing or you could just have water in your fuel.... buy a couple bottles of gas line antifreeze (it sucks up water) and add them to your tank when you fill up.... if that doesn't fix it it is likely the coil pack

Apr 16, 2009 | 2004 Chrysler Sebring

Not finding what you are looking for?
2002 Dodge Intrepid Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...