Question about 1992 Nissan Sentra 4 Door

1 Answer

Need to replace rear left turn signal light on 92 sentra. do I access it from back of fixture (ie, remove fixture) or does outside cover come off?

Posted by on

  • Anonymous Mar 16, 2014

    remove and replace left front ddirectional fixture wire damaged by rodent

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 521 Answers

Thru the trunk. Peel back the inside covering( may have retainer screws or buttons) you will either see the individual sockets or a cple additional screw/bolt/nuts. Most likely will be retainer buts. remove those and the lens will fallout(be ready to catch it) the replace bulbs as needed and reinstall in reverse order from removal.

Posted on Jul 31, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing license plate bulb 2008 Honda Odyssey how do I replace the bulb


often have an access panel you can remove to acces the bulbs from the rear door on the inside, if not you must remove the light fixture from the outside either my removing a screw holding the light housing or carefully pulling the plastic lens out, generally there is a or multiple screws holding the light fixture in place.

Jan 30, 2017 | Honda Cars & Trucks

1 Answer

Where is the transmission temperature censer located on a 2003 Buick regal?


(391) Automatic Transmission Fluid Temperature (TFT) Sensor
Inside the transmission behind side cover
Removal Procedure
Remove the case side cover. Refer to Control Valve Body Cover Replacement .

Important: Lock steering wheel in centered position with wheels straight ahead.
Remove the engine dress cover.
Remove the air cleaner intake duct. Refer to Air Cleaner Inlet Duct Replacement in Engine Controls - 3.1L or Air Cleaner Inlet Duct Replacement in Engine Controls - 3.8L.
Remove the engine mount struts. Refer to Engine Mount Strut Replacement in Engine Mechanical - 3.1L or Engine Mount Strut Replacement - Right Side and Engine Mount Strut Replacement - Left Side in Engine Mechanical - 3.8L.
Important: For supercharged engines, remove the throttle cable bracket.
Disconnect the shift cable bracket.
Remove the transaxle top side cover bolt.
Install the engine support fixture. Refer to Engine Support Fixture in Engine Mechanical - 3.1L or Engine Support Fixture in Engine Mechanical - 3.8L.
Disconnect the transmission wiring harness connector.
Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
Remove the left front tire and wheel assembly. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
Remove the left inner splash shield 3 push pins.
Loosen the wheel speed sensor harness from the 5 retainers at the cradle.
Remove the transmission support to cradle nuts only. Refer to Transmission Mount Replacement .
Raise the vehicle.
Remove the front splash shield 5 bolts.
Loosen the engine mount lower nuts. Refer to Engine Mount Bracket Replacement in Engine Mechanical - 3.1L or Engine Mount and Bracket Replacement in Engine Mechanical - 3.8L.
Remove the stabilizer bolts and reposition the stabilizer.
Remove the steering gear cradle bolts, then support gear before lowering cradle.
Support the left side of the frame with a jackstand.
Remove the left side frame bolts. DO NOT loosen the right front or the right rear frame bolts. Refer to Frame Replacement in Frame and Underbody.
Remove the left ball joint from the steering knuckle.
Position the drain pan under the transaxle.
Remove the left drive axle from the transaxle. Refer to Wheel Drive Shaft Replacement in Drive Axle.
Secure the drive axle to the steering knuckle/strut.
Adjust the jackstand to lower the left side of the frame until it hangs free. Remove jack stand.
Lower vehicle to access engine support fixture.
Lower the engine/transmission assembly with the engine support fixture to gain access to remaining side cover bolts.
If replacing the side cover, remove 4 engine mount bracket bolts.
Remove the harness retainer.
Raise vehicle to access side cover bolts.
Remove the case side cover bolts (56-58).
Remove the case side cover pan (53).
Remove the case side cover gasket (54).
Clean the case.
Clean the side cover gasket mating surfaces.

Disconnect the wiring harness assembly from the fluid temperature sensor (391).
Remove the fluid temperature sensor (391).
Installation Procedure
Install the fluid temperature sensor (391).
Connect the wiring harness assembly to the with fluid temperature sensor (391).
Install the case side cover. Refer to Control Valve Body Cover Replacement .
Important: It is recommended that transmission adaptive pressure (TAP) information be reset. Resetting the TAP values using a scan tool will erase all learned values in all cells. As a result, The ECM, PCM or TCM will need to relearn TAP values. Transmission performance may be affected as new TAP values are learned.
Reset the TAP values. Refer to Transmission Adaptive Functions .

Nov 23, 2016 | Buick Cars & Trucks

1 Answer

How do i replace left rear brake light bulb


1) Open trunk
2) Remove small round plastic access panel with a flat tip screw driver by prying open
3) Remove flat tip screw holding tail light assembly
4) Remove tail light assembly by pulling outward, careful not to break plastic guide/nub
5) Disconnect wiring connectors
6) Remove plastic housing access plate on back of tail light assembly by twisting/turning tabs until they click and then lift access plate from tail light assembly
7) When viewing the the bulbs, the turn signal bulb is the bottom left bulb
8) Install in reverse order, ensuring tail light seal seats properly during installation

Oct 13, 2014 | 1999 Audi A4

1 Answer

Need to change rear brake light bulb on a 2000_L sedan. Owners manual addresses only the turn signal bulb change proceedure. The brake light fixture is flat not round.


there is an access cover in the trunk.Open that and just pull the bulb fixture out replace the bulb and place back in the hole.

Apr 07, 2012 | Saturn Cars & Trucks

1 Answer

How to change the left rear signal light


under the panel cover, inside the trunk, you will see where the light fixture attaches, remove those plastic hold down nuts, and the light should pop right out,, ( I've done a 03,, I believe the 05 is the same) in the Malibu the light goes out the back, and then you can access the bulbs,, In the Impala it either works like that too, or once the panel cover is moved out of the way, the bulb sockets are right there, you just twist them to remove them, but be careful, of the 3 tongs that are part of the socket, One is a bit larger, and people often force them back in , which will break the socket, so be sure and line it up correctly

Oct 07, 2011 | 2005 Chevrolet Impala

1 Answer

How to replace passenger turn signal bulb


The side marker light must be removed in order to get at the turn signal light.
There are two screws holding the side marker light which is situated above the turn signal.
Open the hood.
Remove the phillips head screw at the top of the side marker light.
Using a long #2 Phillips screwdriver, remove the screw on the outside of the side marker light. This can be seen by looking between the lower side of the side marker light and the top side of the turn signal.
The side marker can be moved.
The turn signal has one screw on the top of the fixture that must be removed.
Slide out the turn signal fixture. There is a small feature on the lower front corner of the turn signal fixture that you must note to properly reinstall the turn signal.
In order to get to the bulb, rotate the bulb socket 1/4 turn CW or CCW. The bulb socket is loose.
The bulb is simply pressed into the socket.
Not sure of the type, but it can be found at your locale auto parts store.
The bulb is used in several places on the 1994 GC, so get apacket with two, if possible.
Assembly in reverse. Be careful not to overtighten the screws as they are replaced

May 08, 2011 | 1994 Jeep Grand Cherokee

3 Answers

How to replace rear turn signal light bulb. how do you remove the rear tail light cover so as to remove the bulb on 2006 Ford Explorer XLT


I just changed my rear turn signal. Really easy. There is two 1/4 inch bolts visible when you open the tailgate. Take both of those out and gently lift the light housing out towards the outside of the vehicle. There is two small clamps on the other side of the fixture that just slide right out when you pull on it. There you go

Feb 20, 2010 | 2006 Ford Explorer

1 Answer

Left turn signal while lights are on both signals flash like the hazard lights are on. also the left turn indicator on the dash remains lit.2002 focus


You will most likely find either a poor ground, that allows current to run back through other circuits, or a bulb problem. invoke the problem (turn on headlights) then remove one bulb at a time, at the front and rear. After each removal, go back to dash and observe...

While removing, check grounding of the fixtures, as you go..

Doc

Sep 18, 2009 | Ford Focus Cars & Trucks

2 Answers

1999 Lexus GS300 license plate lights


You access these bulbs from the inside of the trunk lid. Remove the carpet type cover by inserting a small slot screwdriver in the opening of the holding clips. Remove all of the clips, and the cover comes off easily. Then you can reach in through holes in the metal to access the lights. You will need to twist the bulb holder like you would if you were unscrewing a standard screw (counter clockwise) from the side the wire attaches to the light bulb socket. It's a snap in place fixture, so it can be tough to turn. When it comes loose, it only needs to turn a small amount to remove the light fixture from the socket that holds it in place. Once you have it out, simply pull the bulb straight out and put the new one in. Then reverse the process that you used to take it all apart.

Happy motoring!

Jul 01, 2009 | 1997 Lexus ES 300

Not finding what you are looking for?
1992 Nissan Sentra 4 Door Logo

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...