Question about 1994 Land Rover Discovery

Open Question

How the spurk plug wiring at the coil packs are connected for 1992 descovery

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bought coil pack for 92 pontiac bonneville connected wires underneath pack and spark plug wires now will not start at all


Did you replace all three coil packs or just one?
Did you get the spark plug wires in theproper order? (if not it may not start).
What wire did you connect underneath the coil pack (there are no wires under the coil pack). A wire bolts/plugs up to the side of the coil pack.

Jul 29, 2014 | Cars & Trucks

1 Answer

I have a 1992 buik century and it hesitates when i accelerate i changed the wires ,plugs n fuel filter . any ideas ?


CAN YOU GIVE ME THE ENGINE SIZE?CHECK AND MAKE SURE YOUS COIL PACK IS GETTING A GOOD GROUND,AND WHAT HAPPENS IS THE COIL PACK IS MOUNTED ON A PLATE WITH A DIELECTRIC GREASE BETWEEN THE PACK AND PLATE,MAKE SUR IT IS CLEAN UNDER THE PACK AND IT IS GROUNDED GOOD.NEXT CHECK YOUR CONNECTIONS ON YOUR SENSORS,DOES IT IDLE GOOD,I MEAN NO MISSING OR FLUCTUATION WHEN IDLING.CLEAN THE MASS AIR FLOW SENSOR WHICH IS IN THE AIR DUCT.TAKE IT OUT BUT FIRST TAKE OFF YOUR NEGATIVE CABLE AND THEN TAKE OT THE SENSOR AND BE VERY CAREFUL AND CLEAN IT WITH SPRAY GUMMOUT.THIS MIGHT BE YOUR SOLUTION,,LET ME KNOW.

Jan 02, 2012 | 1992 Buick Century

1 Answer

I have a fithe wire in my plug wire set for my 1992 hodna accord and i dont no were it goes


That would be for the Coil to Distributor Wire. If your car has a "Coil Pack" you don't need the wire.

Aug 29, 2011 | 1992 Honda Accord

2 Answers

I need the location of the ignition coil on a 92 cutlass ciera 2.5.


near the fire wall in the back of the engine at the bottom of the engine follow the wire from the spark plug to the back they are connected to the coil. thank for using fixya

Mar 02, 2011 | 1992 Oldsmobile Cutlass Ciera

2 Answers

1992 mazda mpv, 6 cyls. it occurs a year ago after tune up. its luck power. during smog test, and now it cranks but wont go through when it start. changed the rotor, spurk plugs and cable


Check your gas for possible water. Just in case try a can of SEAFOAM in your gas. It will take about 10 min of running to work. Also recheck the gap on the spark plugs it should be .044 gap. One other thing to check is the firing order and make sure the wires were put back in the right place to the right spark plug

Jan 10, 2011 | 1992 Mazda MPV

1 Answer

Firing order for spark plugs and wires for 1992 Buick LeSabre


1992 Buick LeSabre 3.8 liter V-6 VIN "L"

Identifying Ignition Types I and II

On Type I coil packs, three twin tower ignition coils are combined into a single coil pack unit.

fc6d77d.gif


On Type II coil packs, the coils can be replaced separately and the ignition wires are all on the same side of the coil pack.

With Type I Ignition

c07c1ad.gif

With Type II Ignition

517e836.gif

Hope helps (remember rated and comment this).

Aug 17, 2010 | 1992 Buick LeSabre

1 Answer

What is the firing order of the 3.8L engine in a 92 olds 88? Changing spark plug wires & must have switched order


1992 Oldsmobile Delta 88 3.8 liter V-6 VIN "L" - Identifying Ignition Types I and II

On Type I coil packs, three twin tower ignition coils are combined into a single coil pack unit.

5582ccc.gif


On Type II coil packs, the coils can be replaced separately and the ignition wires are all on the same side of the coil pack.

With Type I Ignition


669dd08.gif


With Type II Ignition

d6a3659.gif

Hope helps (remember comment and rated this).

Jun 18, 2010 | 1992 Oldsmobile 88

1 Answer

Dont know how to take master cylinder off to replace coil pack


You shouldn't have to remove it....here are the steps from the tech manual:

Removal & Installation
  1. Disconnect the negative battery cable.
  2. Label and disconnect the spark plug wires from each of the coil pack towers.
3db79bc.gif
Ignition coil removal—2.4L engine

2f61688.gif
Ignition coil removal—3.3L and 3.8L engines


  1. Disengage the electrical connector from the ignition coil pack.
  2. Remove the coil pack mounting fasteners.
  3. Remove the coil pack from the vehicle. If equipped, remove the coil pack from the mounting bracket.
To install:
  1. Place the coil pack into position on top of the engine valve cover, or mounting bracket, if equipped.
  2. Install and tighten the coil pack mounting fasteners to 9 ft. lbs. (12 Nm).
  3. Plug in the electrical connector to the ignition coil pack.
  4. Connect each spark plug wire to each corresponding coil pack tower. The coil pack towers are numbered with the correct cylinder identification. Be sure that the spark plug wires snap firmly onto each coil tower.
  5. Connect the negative battery cable.

Jan 18, 2010 | 2001 Chrysler Voyager

1 Answer

Wiring diagram f150 spark plug wires


The COIL PACK TOWERS are numbered : coil----3---4 pack---2---6 plug----1---5 ----------------------------------------------------------------- The engine cylinders / spark plugs are numbered : passenger side , front to rear , 1 , 2 , 3 -----drivers side , front to rear , 4 , 5 , 6 ------------------------------------------------------------------- The spark plug firing order is ( 1 -4 - 2 - 5 - 3 - 6 )

Oct 26, 2009 | 1992 Ford F150 SuperCab

3 Answers

92olds cutlas cierra, 3.3 liter


how do you check your coils is there a photo that shows you how? or a video, web site




Jun 26, 2008 | 1992 Oldsmobile Cutlass Ciera

Not finding what you are looking for?
1994 Land Rover Discovery Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

74896 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7689 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...