Question about 2004 Mitsubishi Endeavor

Open Question

How to change fuel filler hose and approximate cost

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 Honda Pilot Evap code P1456 Changed gas cap from honda and still


code p1456 refers to evaporative emission (EVAP) canister purge system(fuel tank system) -leak detected===causes--hose-fuel tank/pressure sensor--fuel filler cap--EVAP valve /bypass solenoid--EVAP two way valve---EVAP canister/vent valve

There is also a second reference to the code which is EVAP system leakage ====filler cap--EVAP canister purge valve--hoses---EVAP canister shut off valve---ECM programming---ECM

Check with the service dealer that the filler caps are interchangeable . It may be coincidence that the problem started after you changed caps or it may have shown a failure in the making

Aug 19, 2014 | Cars & Trucks

1 Answer

Evap system


The FSM is clear on this. each hose and fitting must be air tight.
or the the car vents gas fumes full time, and the EVAP ECU tests
(monitor) make sure this all works.
you can just look at the left and right side above rear tires. and see
if your hands are small enough to fit here. Id bet not.
some mech, report, the tank can be tilted down at front (drained fuel)
and gain access.
keep in mind, you get fuel siphoning at any time. do not open the system, with fuel in the tank, and then drive to autozone,
i loosen the gas cap so that pressure can not build in tank.
expanding fuel can push fuel out , during a filter change. very
dangerous in a garage, and you gone.
it's just a vent hose, you can see, it and what needs to be done is really obvious. given you arms sides and lenght.
my fsm states, " TANK pull"

Removal & Installation

  1. Relieve the fuel system pressure and disconnect the negative battery cable.
  2. Remove the fuel filler cap from the fuel tank.
  3. Have a Class B fire extinguisher near the work area. Use a hand operated pump device to drain as much fuel through the fuel filler neck as possible.
  4. Use a siphon to remove the remainder of the fuel in the tank by connecting the siphon to the fuel pump outlet fitting.
    CAUTION Never drain or store fuel in an open container because there is the possibility of a fire or an explosion.
  5. Reinstall the fuel filler cap.
  6. Remove the rear seat cushion from vehicle (if so equipped).
  7. Disconnect the fuel pump motor connector and sending unit electrical connectors.
  8. Disconnect the wire harness grommet and harness through the vehicle floor pan.
  9. Raise and safely support the vehicle.
  10. Remove the fuel filler hose clamp from the filler neck assembly.
  11. Remove the fuel breather hose clamp from the filler neck assembly.
  12. Remove the fuel filter inlet hose clamp and hose from the filter.
    NOTE A small amount of fuel may be released after the fuel hose is disconnected. In order to reduce the chance of personal injury, cover the fitting to be disconnected with a shop towel.
  13. Remove the fuel vapor clamp and hose, and fuel return hose clamps and hose from the respective fuel lines.
  14. Using a suitable transaxle jack, support the fuel tank.
  15. Remove the fuel tank retaining bolts and lower the tank.
To install:
  1. Reconnect all fuel hoses, lines and the fuel breather hose to the fuel tank.
  2. Place the fuel tank in its proper space using the transaxle jack, Install the fuel tank retaining bolts.
  3. Remove the transaxle jack.
  4. Reconnect all fuel hoses, lines and the fuel breather hose to the fuel tank.
  5. Install the fuel breather hose and hose clamp to the filler neck assembly.
  6. Install the fuel vapor hose and hose clamps. Install the fuel return hose and hose clamp to the respective fuel lines.
  7. Install the fuel filter inlet hose and hose clamp to the filter.
  8. Lower the vehicle. Install the wire harness and grommet through the vehicle floor pan.
  9. Connect the fuel pump motor and the sending unit connectors.
  10. Install the rear seat cushion. Reconnect the negative battery cable.
"

Mar 26, 2013 | 2002 Suzuki Esteem

1 Answer

FUEL BACKS UP AND SPILLS ON THE GROUND ON 04 KIA OPTIMA


There are no valves causing your problem. You have purely a plumbing isue. Some fuel stations pump fuel faster then the size and orientation of your filler tube will take. Don't be in such a rush when putting your 15 gallons in run the fuel nozel on slow.

Sep 18, 2012 | 2004 Kia Optima

1 Answer

What is the best way to change the fuel pump?


Hi, welcome to FixYa.com my name is Shawn and I will be answering your question.

  1. Relieve the fuel system pressure. Refer to the procedure in this section.
  1. Disconnect the battery ground cable (14301) .
  1. Drain the fuel from the fuel tank (9002) . Refer to the procedure in this section.

    Fuel Tank and Related Components
  1. Raise and support the vehicle.
  1. Remove the two pins from the fuel tank front protector.
  1. Remove the three fuel tank front protector bolts and remove the fuel tank front protector.
  1. Disconnect the evaporative emission hose (9E325) from the evaporative emission valve (9B593) .
  1. NOTE: Label the fuel return line and fuel supply line to ease installation.
    Loosen the fuel return hose clamp and slide it away from the fuel return hose connection.
  1. NOTE: Use a rag to prevent fuel from spilling while disconnecting the fuel lines.
    Disconnect the fuel return hose at the fuel tank .
  1. Loosen the fuel supply hose clamp and slide it away from the fuel supply hose connection.
  1. Disconnect the fuel supply hose at the fuel tank .
  1. Disconnect the fuel pump and bracket electrical connector.
  1. Loosen the hose clamp from the fuel tank to filler pipe hose (9047) and slide the hose clamp toward the fuel tank .
  1. Separate the fuel tank to filler pipe hose from the fuel tank filler pipe (9034) .
  1. Place a jack under the fuel tank to support it when the fuel tank support straps are removed.
  1. Remove the two fuel tank support strap bolts and allow the fuel tank support straps to hang down.
  1. Remove the spring clips from the fuel tank support strap hinges.
  1. Remove the fuel tank support strap hinges and remove the fuel tank support straps.
  1. NOTE: An assistant may be necessary to remove the fuel tank .
    Lower the fuel tank from the vehicle.


I hope my assistance helped you and resolved your concern, if you need further assistance please ask.

Aug 08, 2011 | 1995 Mercury Villager

1 Answer

FUEL FILLER PIPE DIAMETER? i just bought a 99 cougar, needs a new fuel filler tube to pas inspection. the part new cost 350, and i dont have that kind of cash. so im going to rig a fuel filler hose onto...


Is the actual filler tube rusted or busted? If so just get a new one from the junkyard, Id not recommend you rig it with a piece of hose for a lot of reasons.

Now if your talking about the little piece of hose that connects the filler neck to the tank, you just need to measure it, and or bring the hose into a parts store. They usually do those hoses in millimeters.

Jul 02, 2011 | 1999 Mercury Cougar

2 Answers

HOW TO REPLACE A FUEL PUMP FOR A NISSAN XTERRA



Removal & Installation

  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Relieve the fuel system pressure.
  3. Drain the fuel tank.
  4. Remove or disconnect the following:

    Negative battery cable Fuel pump module harness connectors Filler hose shield Fuel pressure and return lines Filler hose Vent hose Evaporative Emissions (EVAP) hose Fuel tank skid plate Fuel tank Fuel level sender Fuel pump

To install:
  1. Install or connect the following:

    Fuel pump Fuel level sender. Tighten the screws to 17-23 inch lbs. (2.0-2.5 Nm). Fuel tank. Tighten the bolts to 27-36 ft. lbs. (37-49 Nm). Fuel tank skid plate. Tighten the bolts to 27-36 ft. lbs. (37-49 Nm). EVAP hose Vent hose Filler hose Fuel pressure and return lines Filler hose shield Fuel pump module harness connectors Negative battery cable
  2. Fill the fuel tank.
  3. Start the engine and check for leaks.

Mar 31, 2010 | 2005 Nissan Xterra

1 Answer

Removing tank


Disconnect battery ground cable. Loosen fuel filler cap. Support underneath of the fuel tank protector Disconnect evaporative fuel hose at the canister. Disconnect fuel feed hose and fuel return hose near the fuel filter. Plug both ends of the fuel hoses to prevent fuel leakage. Disconnect air breather hose and fuel filler hose at the fuel filler neck. Cover fuel hose to prevent any dust entering. Remove the four fuel tank assembly fixing bolts at four corners of the tank. Let down the tank and disconnect the wiring connectors Remove fuel tank assembly along with protectors Remove retaining cover and roll over & float valve along with the evaporative fuel hose and pipe Remove fuel pump and sender assembly by removing the snap ring with the fuel hoses Remove protectors by removing the six fixing bolts

Jun 12, 2009 | 1999 Isuzu Rodeo

1 Answer

Can you tell me how to change fuel pump on a 1990 chevy lumina


http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152801dbaf3

when you drop the tank by following these directions you will have access to the pump

1989-94 Vehicles
See Figures 1 and 2
  1. Disconnect the negative battery cable.
  2. Properly relieve the fuel system pressure, as outlined earlier in this section.
  3. Raise and safely support the vehicle.
CAUTION Observe all applicable safety precautions when working around gasoline. Do not allow fuel spray or fuel vapors to come in contact with a spark or open flame. Keep a dry chemical (Class B) fire extinguisher near the work area. Never drain or store fuel in an open container due to the possibility of fire or explosion.
  1. Use a suitable hand operated pump device to drain the fuel through the filler tube into an approved container.
Before disconnecting any fuel lines from the fuel tank, thoroughly clean around all hose connections.
  1. Disconnect the fuel filler vent hose from the fuel tank.
  2. Detach the fuel filler hose from the fuel filler inlet tube on the fuel tank. Position the hose out of the way.
  3. Disconnect the vapor hose from the front of the fuel tank.
  4. Detach the fuel return pipe and position the hose out of the way.
  5. Disconnect the two rear rubber exhaust hangers from the rear of the exhaust system and allow the exhaust system to hang down slightly.
  6. Unfasten the exhaust shield mounting bolts, then remove the exhaust shield.
  7. Support the fuel tank with a suitable jack.
  8. Remove the two bolts securing the fuel tank straps, then swing the straps out of the way.
  9. Lower the fuel tank enough to disconnect the vapor hose from the fuel sender assembly and the vapor hose from the vapor pipe at the rear of the fuel tank.
  10. Detach the electrical connector from the fuel sender assembly and remove the two retaining clips.
  11. Remove the tank from the vehicle, slowly to ensure all connections and hoses have been disconnected.
To install:
  1. Clean all parts well. Inspect the tank for dents, rust or other damage. On high-mileage vehicles, it may be good practice to remove the fuel pump module and replace the flexible strainer on the fuel pump.
  2. Position the fuel tank under the vehicle and raise the tank with a suitable jack.
  3. Connect the vapor hose to the fuel tank at the vapor pipe at the rear of the tank and connect the vapor hose to the sender assembly.
  4. Attach the electrical connector to the fuel sender assembly.
  5. Connect the fuel feed and return lines to the sender assembly.
  6. Raise the tank into position into the vehicle and swing the mounting straps under the tank.
  7. Install the front fuel tank strap mounting bolts and tighten to 35 ft. lbs. (47 Nm).
  8. Remove the jack.
  9. Connect the fuel return pipe to the fuel feed pipe.
  10. Attach the rear fuel feed pipe to the inlet side of the fuel filter.
  11. Tighten the line fittings to 16 ft. lbs. (22 Nm). Make sure to use a back-up wrench to prevent the fuel filter from turning.
  12. Connect the vapor hose to the vapor pipe at the front of the vehicle.
  13. Attach the fuel filler vent hose to the tank. Connect the fuel filler hose to the fuel filler neck of the tank.
  14. Install the exhaust heat shield and the mounting bolts.
  15. Position the exhaust system and install the rubber hangers.
  16. Carefully lower the vehicle, then refill the fuel system
  17. Connect the negative battery cable, then install the fuel filler cap, if not done already.
  18. Turn the ignition switchONfor 2 seconds, OFF for 10 seconds, thenONand check for fuel leaks.

Jan 14, 2009 | 1998 Mercury Sable

1 Answer

1995 maxima fuel filler tube


Are you going to get a new one, or a junkyard replacement?
You have to take off the rear left tire. Secure the car with jack stands and chucks. There is a plastic cowl on the wheel-well that covers the filler tube to prevent road damage. Take it off. The filler tube is attached to the gas tank through a rubber connector hose (tube) adapter, secured to the gas tank and to the filler tube by hose clamps. Loosen both clamps.. You should replace the rubber connector, as it has been there for many years, and rubber degrades. Loosen about three or four bolts along the filler tube that attach it to the car body. The top part, by the gas lid, comes off easily, it's just a plastic dam. You have to carefully work it off the (other end) at the rubber hose connector. Once it's out, get the hose connector off the gas tank neck.
With the new filler tube, reverse the process. Getting the hose clamp tight over the gas tank neck is hard. Make sure the clamp is seated properly before tightening.
Good luck!

Oct 30, 2008 | 1995 Nissan Maxima

Not finding what you are looking for?
2004 Mitsubishi Endeavor Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...