Question about 1998 Volkswagen Passat

1 Answer

Where is the blower motor relay located and how do you identify the correct relay?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

The blower motor is located in the were the front canparment is you would have to take all the dash board out and you would see the blower motor tru there

Posted on Aug 20, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the fuse for the blower motor on a 2003 matrix


There is a 40amp fuse marked Blower in the fuse box in the engine compartment. The switch and resistor provide the ground circuit to the blower motor.

Jul 16, 2013 | 2003 Toyota Matrix

1 Answer

Blower motro dont work


Hi George, Your first job is to identify the relay which operates and the fuse which protect the circuit. Check them both for correct operation and replace where needed. Regards John

Dec 06, 2011 | 1998 Acura TL

1 Answer

2006 Dodge Ram The blower motor will not blow. No voltage at the resistor. Is there a relay in the system? All fuses are good. Thanks for the help.


Yes, there is a blower motor relay located in the PDC box under the hood. It is a black box with a removable cover, and the underside of the cover will show the correct relay location.

Jan 27, 2011 | 2006 Dodge Ram

2 Answers

Where is the blower motor relay located


Under the passenger side of the dash is the blower resister .This is most likely the cause they tend to burn up and your blower stops working.:)Also look for the connector going to the blower motor in the same location it is probably burnt on the end also.

Jan 31, 2010 | 1998 Ford Escort

1 Answer

Access location of front heater blower motor


It located behind the dash on the Passenger side.
And yes you can easily do this yourself saving you alot of money! Have you first checked the Front Blower Motor Relay located in the IPM Relay and Fuse Box located inside the engine compartment? Remove the cover. The location identification is located on the back (inside) side of the Cover. You can switch-out a similiar size and shape Relay and check the operation. If the Blower now works then the Relay was bad and needs to be replaced. The Motor and Resistor cost alot more money than the Relay.
Before we do this: What is the Motor doing? Nothing? OR DOES IT WORK ON HIGH ONLY? If the Motor works on High only then it is not the Motor but the Blower (Fan) Motor Resistor. This is located near the Motor. It is identified by 3 to 4 wires going into it. Remove the two (2) retaining nuts/metal screws and remove. Disconnect the wiring connection and replace. I don't want you to replace the Motor and find out you wasted your money when it was the Resistor.
It could be also both the Motor and the Resistor.
Direction to remove/replace the Blower Motor:
1. Disconnect the Negative cable from the Battery and wait two minutes. This is to de-energize the Air Bag System which you will be working near.
2. Remove the Glovebox.
3. Remove the four (4) hex screws holding on the Blower Motor Cover.
4. Remove the three (3) nuts/screws holding in the Blower Motor. Make sure you support the Motor, as it will drop down.
5. Disconnect the electrical connection.
Installation is the reverse of the above.
Check operations before putting the Glove Box Back on.

Jan 09, 2010 | 1999 Plymouth Grand Voyager

1 Answer

It doesn't blow off heat was working fine yesterday and just suddenly stopped working


Check the Front Blower Motor Relay located in the IPM Relay and Fuse Box. It's location should be identified on the back side of the cover. There are other exact Relays (like the Spare Relay or the adjacent: Rear Blower Motor Relay or Defogger Relay) that you can switch out and check operations. If the Front works now but not the Rear, it is the Relay and should be replaced.

Jan 02, 2010 | 2003 Dodge Grand Caravan AWD

1 Answer

I have a 2006 Chev Impala that the fan does not operate,


underhood fuse block think it says BATT 4 30amp prob. going to be bad blower resistor

Aug 05, 2009 | 2005 Chevrolet Impala

1 Answer

Blower motor relay 1995 Ford econoline


Relays Blower Motor Relay(s)
The blower motor relay is located in the relay panel on the left front fender apron (16054). When the blower motor circuit is energized, the contact within the relay closes to complete the circuit for blower motor operation.

Mar 21, 2009 | 1993 Ford Econoline

3 Answers

Blower motor stopped working.


https://www.genuineservice.com/genuineservice/en/default?page=genuineService

Go to this site and you can get a copy of your owners manual. Just pic the owner's manual link in the left side task bar.
The relay is located in the interior fuse panel. It should show you a diagram of the fuse panel in the owners manual.

Mar 02, 2009 | 2003 Ford Taurus

2 Answers

Blower for Heat/A/c not working


Blower Motor Resistor Replacement Removal Procedure
  1. If equipped, remove the IP sound insulator.

  2. 476821.gif

  3. Disconnect the electrical connection from the blower motor.
  4. Disconnect the electrical connection from the blower motor resistor.

  5. 382493.gif

  6. Remove the blower motor resistor retaining screws.

  7. 382503.gif

  8. Remove the blower motor resistor.
Installation Procedure

    382503.gif
  1. Install the blower motor resistor.

  2. 382493.gif

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
  3. Install the blower motor resistor retaining screws.
  4. Tighten
    Tighten the screws to 1.6 N·m (14 lb in).

    476821.gif

  5. Connect the electrical connection to the blower motor resistor.
  6. Connect the electrical connection to the blower motor.
  7. If equipped, install the IP sound insulator.

Dec 08, 2008 | 2001 Chevrolet Silverado 1500

Not finding what you are looking for?

Open Questions:

See all 1998 Volkswagen Passat Questions

1998 Volkswagen Passat Logo

341 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8201 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...