Question about 1994 Mercury Cougar

1 Answer

How to remove a door panel on a 95 Mercury Cougar

The power window motor is running,but the windows do not move.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Find any screws and take them out first then u want to slide the panel upwards until it releases

Posted on Aug 09, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I am having trouble with my 1990 Mercury Cougar window. The power window was running and would not go down so I forced it down half way. The motor is running but nothing is moving... Since I pushed it down...


You'll have to replace the regulator/motor assembly with a new one if the mechanism was damaged, which sounds like it was. Plastic parts break on these systems. If it is snowing and you don't have the resources to replace it right now, try to tape some plastic over the window using duct tape. But, this is only a temporary solution.

Nov 04, 2011 | 1990 Mercury Cougar

1 Answer

99 mercury cougar replaced power window motor and switch window still does not work


That doesn't seem possible does it ?

You remove the inner door panel

You think the motor may be bad,so you unplug it,
knowing it is a DC Motor & can be hooked up either
way & will run in either direction
You put 12 volts to it. Doesn't work ,sounds bad,you
install a new one

Now you need power from the switch to run the new motor,
so you work on that
The switch can be disconnected & tested with an OHM Meter
& if worn,you replace that
You checked the fuse before you started & knew that wasn't an issue,
because all the other windows worked

So what did you mis ,short of having no wiring diagram, to make
things a lot easier?

Aug 04, 2011 | 1999 Mercury Cougar

1 Answer

Door window motor runs in both directions but window does not move. removed the door panel but need help to proceed


There is a motor at the bottom of the door that is attached to a guide that runs the window up and down..You have a broken guide with a little time and patience you can replace it

Jun 10, 2011 | 1994 Mercury Cougar

1 Answer

How to remove the door panel on 1991 mercure cougar. I need to replace window motors.


DOOR TRIM PANEL

1989-92 Models
(see Figure 8 - click over pic for zoom)
  1. Remove window regulator switch housing.
  2. Remove the door inside handle cup (snaps out).
448e137.jpg

Fig. 8: Door trim panel-1989-92 models
  1. Remove the self tapping screw retaining door trim panel upper front extension assembly, and remove assembly.
  2. Remove the two self tapping screws retaining door trim panel to the door inner panel.
  3. Lift the door trim panel upward and snap out trim panel.
  4. Disconnect the wire harness for courtesy lamp.
To install:
  1. Attach the wiring harness to the courtesy lamp.
  2. Place the door panel into position, then tighten the panel to the inner panel.
  3. Attach the upper front extension assembly.
  4. Snap the door handle cup on the door assembly.
  5. Install the window regulator switch housing.


Electric Window Motor
REMOVAL & INSTALLATION
  1. Remove the trim panel and watershield.
  2. Remove the speakers.
  3. Disconnect the negative battery cable.
  4. Disconnect the motor wires and the connector.
  5. Using the dimples located on the inner door panel, drill 3 / 4 in. (19mm) holes for access to the motor.
WARNING When drilling the holes, the glass must be in the up position. The hole saw pilot must not extend more than1/4in. (6mm) beyond the hole saw.
CAUTION Secure the regulator in a vise and drill a5/16in. (8mm) hole through the regulator sector gear and the plate. Install a1/4in. (6mm) bolt and nut in the hole to prevent the sector gear from moving when the motor and drive assembly is removed.
  1. Working through the holes, remove the 3 motor and drive-to-regulator attaching bolts. Remove the motor and drive from the door.
To install:
  1. Clean the chips of metal from the surrounding area. Then coat the bare metal to avoid rust.
  2. When installing the motor and drive to the regulator and install the 3 screws just snugly enough to hold it. Remove the regulator restraining bolt and nut if the old regulator was re-used.
  3. Connect the negative battery cable.
  4. Connect the wires and cycle the glass through its run to ensure gear engagement. Then, tighten the attaching screws to 50-85 inch lbs. (6-10 Nm).
  5. Install the speakers and door trim panel with watershield.

Hope helps (remember rated this).

Jun 25, 2010 | 1991 Mercury Cougar

1 Answer

How to install a new power window motor in my 1993 Mercury Grand Marquis? I have a 1993 Mercury Grand Marquis Ls and the power window doesn't work. So then I bought some new window motors and I was...


Remove all screws to door panel. Remove the lock and window controls. Then take large flat-tip screwdriver and gently pry directly next to plastic studs holding panel on to door. Lift door panel off. Remove plastic out of the way. You will now have access to window motor. You may have to solder off old wiring. Or if you have enough to cut, would be good

Sep 11, 2009 | 1993 Mercury Grand Marquis

1 Answer

2002 Cougar passenger side window switch - remove & replace


remove the door panel switch comes off from inside

Jul 23, 2009 | 2002 Mercury Cougar

3 Answers

95 town car power windows


take off door panel and see if the regulator is rusted or there may be a bind in it use white litham grease make sure your hands are out of the way when operating the motor

Jan 02, 2009 | 1995 Lincoln Town Car

2 Answers

1993 Mercury Cougar power window, driver side, will not move


It could be one of about 3 things, the switch could be bad, the motor, or the window regulator. Sometimes you can hit the lower part of the door a couple of times wile holding the window switch to check the motor. I don't know how to check the switch but the cable on the regulator can brake and wrap around the motor not allowing it to run. The only way to check this is to take the door pannel off and see if the cable is broke.

Jan 01, 2009 | 1993 Mercury Cougar

2 Answers

1995 Mercury Cougar Door Panel Removal


This nearly drove me crazy on our 1994 Cougar.
First remove the electric switch cover(window and mirror controls). Just pops out with a pry. Remove the harness attachments You will see a single screw into the door holding a bracket between door pad and door frame. Remove it.
Second, remove the door lamp plastic cover at the bottom rear of the door. You will find a second screw in there on the upper right corner. Remove it and you are ready. Pull the whole door pad upward and it comes right off. No popem plastic clips or anything else. Just 3 or 4 quarter circle retainers that pop over into the door when you push the pad back down

Oct 26, 2008 | 1995 Mercury Cougar

Not finding what you are looking for?
1994 Mercury Cougar Logo

406 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

fordexpert

Level 3 Expert

5501 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...