Question about 1999 Jeep Grand Cherokee

1 Answer

How do you remove the steering colomn shroud?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 17,970 Answers

Review this information:
- Steering column opening cover

- Steering Column Assembly / PDF (only as guide reference)

Good luck!!!





































Posted on Aug 14, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the Shroud on the steering column of a 2003 Ford Escape and what tool can I use to remove it


Steering column shroud is the plastic cover just below the steering wheel that tidies away from sight the switches, wiring and connectors beneath.

Most shrouds are sectional and held in place with a combination of partially hidden screws, disguised screws and internal clips. Some shrouds aren't sectional and the steering wheel must be removed as a first step towards removal.

Please be aware modern steering wheels have the airbag and beneath the shroud is the wiring and connections. It isn't wise to fool around in there unless you know what you are doing.

Feb 18, 2017 | 2003 Ford Escape

1 Answer

Steering column top bearing replacment


double posted, with 1999 added.
the FSM says dont reuse steering wheel bolts.. (unique)
here is an online quote to get to the combo switch
quote;
Removal & Installation
  1. Disconnect and isolate the battery negative cable. WARNING(bags can kill, my comment)
    Wait two minutes for the airbag system reserve capacitor to discharge before performing further diagnosis or service.
  2. From below the steering column, remove the three screws that secure the lower steering column shroud to the multi-function switch mounting housing.
  3. Using hand pressure, push gently inward on both sides of the upper shroud near the parting line between the upper and lower shrouds to release the snap features that secure the two shroud halves together.
  4. Remove both the upper and lower shrouds from the steering column.
  5. Remove the Steering Control Module (SCM) from the steering column.
  6. Remove the two screws that secure the left multifunction switch to the SCM .
  7. Disengage the two retaining tabs , next to the screw mounts that secure the left multi-function switch to the SCM.
  8. Disconnect the left multi-function switch from the SCM.
To install:
  1. Position the left multi-function switch onto position on the Steering Control Module (SCM) .
  2. Engage the two retaining tabs, next to the screw mounts that secure the left multi-function switch and firmly snap into place.
  3. Install the two screws that secure the left multifunction switch to the SCM. Tighten the screws to 22 inch lbs. (2.5 Nm).
  4. Position the lower steering column shroud to the underside of the steering column.
  5. Install the three screws that secure the lower steering column shroud to the multi-function switch mounting housing. Tighten the screws to 17 inch lbs. (2 Nm).
  6. Position the upper column shroud over the steering column with the hazard warning switch button inserted through the hole in the upper shroud.
  7. Align the snap features on the upper and lower shrouds and apply hand pressure to snap them together.
  8. Reconnect the battery negative cable.

Dec 22, 2013 | 1999 Jeep Grand Cherokee

1 Answer

Horn repair at steering colomn


the center section where the horn button is should slide out with some resistance. then one large nut holds the steering wheel on usually accompanied by 2 or 3 small bolts to hold the horn actuator down. it takes a gear puller to actually remove the steering wheel. as for the steering column itself it's a conglomeration of lag screws and plastic covers.

May 17, 2012 | 2007 Nissan Frontier SE Crew Cab

1 Answer

Need to replace ignition cylinder. no keys


This is not an easy repair due to anit theft requirements. need to chisel off bolts.

Section 11-04: Steering Column 1997 Probe Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 05/17/2000
Ignition Switch Lock Cylinder Removal
  1. Remove the steering wheel (3600). Refer to the procedure in this section.
  1. Remove the four lower steering column shroud screws.


    j5021c.gif

  1. Separate the upper and lower steering column shrouds.
  1. Remove the ignition switch lock cylinder illumination miniature bulb from the lower steering column shroud.
  1. Remove the upper and lower steering column shrouds.
  1. Remove the multi-function switch (13K359). Refer to Section 11-05 for the removal and installation procedure.
  1. If equipped, remove the ignition/shifter interlock cable screw.
  1. Disconnect the ignition/shifter interlock cable (3F719) from ignition switch lock cylinder (11582).
  1. Use a chisel to remove the two ignition switch lock cylinder bolts.
  1. Remove the ignition switch lock cylinder from the steering column.
  1. Disconnect the ignition key reminder switch electrical connector.
  1. If necessary, remove the ignition key reminder switch.


    j5028b.gif

Installation
NOTE: Use new ignition switch lock cylinder bolts. Tighten the bolts until the bolt heads break off. Check for proper ignition switch (11572) operation.

To install, reverse the removal procedure.

Mar 25, 2011 | 1997 Ford Probe

1 Answer

How do I replace the turn signal multi-function switch in my 1998 Ford Expedition


SECTION 211-05: Steering Column Switches 1998 Expedition/Navigator Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 02/11/2000 Multifunction Switch Removal
  1. Disconnect the battery ground cable (14301).
  1. Remove the ignition switch lock cylinder (11582).
    1. Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
    1. Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.
    gj0845a.gif
  1. Twist the tilt wheel handle and shank (3F609) and remove.
    gj0846a.gif
  1. NOTE: Move gear selector to lowest position to access steering column opening cover.
    Release the four clips and remove the steering column opening cover.
    gj0847a.gif
  1. Remove the upper and lower steering column shrouds.
    1. Remove the three screws.
    1. Remove the lower steering column shroud.
    1. Remove the upper steering column shroud.
    gj0976a.gif
  1. Remove the multi function switch.
    1. Remove the two screws.
    1. Disconnect the electrical connectors.
    1. Remove the multi function switch.
    gj0848a.gif
Installation
  1. NOTE: When the battery (10655) is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
    To install, reverse the removal procedure.
    gj0850a.gif

2010&c18=modelyear&c20=n130593&c35=wsm%2cmultifunction%20switch%2cswj%2c211-05%2cremoval%20and%20installation&s=1366x768&c=32&j=1.3&v=y&k=y&bw=995&bh=405&ct=lan&hp=n&[aqe]

Mar 08, 2011 | 1998 Ford Expedition

1 Answer

Broken shifter cable, how do i repair it


Put park brake on or block wheels, and shift into neutral (if possible), If not go to tranny and pop the cable off the tranny lever (pry off with screwdriver). Turn tranny shift lever, until it clicks twice, leave here for later adjustment. Follow the cable to the adjuster, pull out the flat steel retainer clip, pinch the sides to remove cable from bracket. Remove upper covers below the steering wheel. Remove kick panel below steering colomn. Remove cable from steering wheel shifter assembly (pry off and remove clip same as at tranny). Remove the side kick panel and follow cable along floor. You may find it easier to remove the driver seat (4 nuts on floor and wiring). Pull cable thru floor and replace. Reverse procedure to install. Lock the cable and clip at steering colomn, but leave the clip off at tranny. The tranny should still be in neutral. Now turn key to run and shift the shifter into neutral. At the tranny side cable there is a white square button, press in and lock cable to lever. install retainer clip. move shifter thru ranges and ensure it locks in park. Readjust if needed by pressing button and moving shifter lever on tranny.

Jan 27, 2011 | 1995 Chevrolet Silverado 2500

1 Answer

Steering wheel moves 1/2 inch to the side


It sounds like the upper steering colomn bowl is loose. The bolts come up from the bottom and hold the lower portion of the steering wheel cover to the upper. The steering shaft runs down thru the middle of both. If loose the steering wheel will rock side to side in the upper bearing race, not holding the shaft tight or straight. Its actually easier to remove the entire steering colomn, turn upside down and tighten. Remove the lower steering shaft at the firewall (mark the spline alignment). Disconnect the electrical connections at the lower colomn. Disconnect shifter (if not floor console shifter). Unbolt from dash and remove the entire colomn, with wheel attached. Flip over and chek the lower bolts for tightness. It can be done from disassembling the colomn, but its a lot of work and lots of little pieces to loose.

Jan 26, 2011 | 1987 Chevrolet El Camino

1 Answer

How to replace the multifunction switch of a 2006 Dodge Ram


REMOVAL
WARNING: To avoid serious or fatal injury on vehicles equipped with airbags, disable the Supplemental Restraint System (SRS) before attempting any steering wheel, steering column, airbag, seat belt tensioner, impact sensor, or instrument panel component diagnosis or service. Disconnect and isolate the battery negative (ground) cable, then wait two minutes for the system capacitor to discharge before performing further diagnosis or service. This is the only sure way to disable the SRS. Failure to take the proper precautions could result in accidental airbag deployment.

1. Disconnect and isolate the battery negative cable.
2. Remove the screw (2) that secures the tilt steering column knob (1) and remove it from the tilt actuator (3) on the left side of the column.
3. From below the steering column, remove the two outboard screws that secure the upper column shroud (1) to the lower shroud (3).
4. Using hand pressure, press inward on both sides of the upper shroud above the parting line of the lower shroud to release the snap features that secure the two shroud halves to each other.
5. Remove the upper shroud from the lower shroud and the steering column.
6. Remove the one center screw that secures the lower shroud to the steering column (4).
7. Remove the lower shroud from the steering column.
8. Disconnect the wire harness connector (2) from the back of the multi-function switch housing (1).
9. Rotate the steering wheel far enough to access and remove the two screws (4) that secure the switch to the multi-function switch mounting housing (3).
10. Grasp the switch control stalk and pull it toward the left side of the vehicle to remove the switch from the mounting housing.

INSTALLATION
1. Slide the multi-function switch (1) into the multi-function switch mounting housing (3) from the left side. Be certain that the alignment pins on the top and bottom of the switch are properly engaged in the channels of the mounting housing.
2. Rotate the steering wheel far enough to install and tighten the two screws (4) that secure the switch to the mounting housing. Tighten the screws to 2 N·m (20 in. lbs.).
3. Reconnect the wire harness connector (2) to the back of the switch housing.
4. Position the lower shroud (3) onto the steering column (4).
5. From below the steering column, install and tighten the one center screw that secures the lower shroud to the steering column. Tighten the screw to 2 N·m (20 in. lbs.).
6. Position the upper shroud (1) onto the steering column over the lower shroud. On vehicles equipped with an automatic transmission, be certain to engage the gearshift lever gap hider into the opening in the right side of both shroud halves.
7. Align the snap features on the upper shroud with the receptacles in the lower shroud and apply hand pressure to snap them together.
8. Install and tighten the two outboard screws that secure the upper shroud to the lower shroud. Tighten the screws to 2 N·m (20 in. lbs.).
9. Position the tilt steering column knob (1) onto the tilt adjuster actuator (3) on the left side of the steering column, then install and tighten the screw (2) to secure the knob to the actuator. Tighten the screw to 2 N·m (20 in. lbs.).
10. Reconnect the battery negative cable.

Sep 14, 2010 | 2006 Dodge Ram 1500

1 Answer

Locked steering wheel


remove top and bottom of steering colomn co(need torqs 20 driver)then check to see if the ign lock is on a white box aprox2x3 f so purchase a new ign switch with lock and tumbler(should have new key)remove old switch (need tamper proof torqs bit for this)INSTALL NEW SWITCH

Oct 04, 2009 | 2001 Dodge Stratus

1 Answer

How do I install headlight switch on 95 mercury tracer?


  • Headlamps Inoperative
  • Fuse.
  • Headlamp switch.
  • Headlamp relay.
  • Circuit.
  • Bulbs.

Section 11-05: Steering Column Switches 1996 Escort, Tracer Workshop Manual
REMOVAL AND INSTALLATION Multi-Function Switch
Removal
  1. stf~us~en~file=ani_caut.gif~gen~ref.gif WARNING: THE ELECTRICAL CIRCUIT NECESSARY FOR AIR BAG DEPLOYMENT IS POWERED DIRECTLY FROM THE BATTERY. TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE PERSONAL INJURY, THE BATTERY GROUND CABLE MUST BE DISCONNECTED PRIOR TO SERVICING OR REPLACING ANY AIR BAG SYSTEM COMPONENTS.
    Disconnect the battery ground cable (14301) and wait one minute for the backup power supply to be depleted.
  1. Remove the steering wheel (3600). Refer to Section 11-04 for the removal procedure.
  1. Remove the four screws from the lower steering column shroud (3530).




  1. Remove the ignition switch lock cylinder illumination lamp socket from the lower steering column shroud.
  1. Remove the lower steering column shroud.
  1. Remove the upper steering column shroud.
  1. Disconnect the three multi-function switch electrical connectors.
  1. Remove the multi-function switch screws.
  1. Remove the multi-function switch electrical connectors and the multi-function switch (13K359).

Jan 16, 2009 | 1995 Mercury Tracer

Not finding what you are looking for?
1999 Jeep Grand Cherokee Logo

Related Topics:

148 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...