Question about 2003 Volkswagen Jetta TDI
Did you take it to computer its probably a bad sensor you will have to check it with computer to see witch one becauce they are many
Posted on Sep 24, 2009
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
With the key in the ignition (but not turned), press and hold the Odometer Reset Button on the right hand side of the panel. While still holding that button, turn the key (although not far enough to start the engine) and then press and hold the Minute button on the left side of the instrument pane(if pressing doesnt work try turning the knob clockwise until service light has gone off and skip the pressing)l. Release both buttons at the same time.
Posted on May 30, 2009
one is located over the battery, the other is located in the side of the dash.
If you pop your hood the battery will be on your right sid in the front of the engine bay. There is a small rectangular piece on top of the battery with a lot of heavy guage red wires going to it. That is the engine bay fuse box.
if you open your driver side car door it's under neath a panel located inbetween the door and the dash board.
Posted on Jun 03, 2009
SOURCE: I have a p2138 code
There is a GM Technical Service Bulletin (TSB) on this issue, below is a summary;
#07-06-04-019A: Intermittent MIL/SES, DTC P2138 with Reduced Engine Power (Repair Instrument Panel (IP) to Body Harness Connector)
Models: 2005-2008 GM Passenger Cars and Light Duty Trucks (Including Saturn)
2005-2008 HUMMER H2
2006-2008 HUMMER H3
2005-2008 Saab 9-7X
Some customers may comment on an intermittent MIL/SES light Illuminated with a message center or an indicator that displays Reduced Engine Power. DTC P2138 - Accelerator Pedal Position (APP) Sensor 1-2 Correlation may be set. The voltage difference between APP sensor 1 and APP sensor 2 exceeds a predetermined value for more than a brief period. Refer to DTC P2138 in SI for further diagnostics.
On some vehicles, the IP to body harness connector, which carries the APP signal to the ECM/PCM, is located in the left hand kick panel area or inside the IP. Water intrusion into these areas could cause an electrical short in the APP circuits setting a P2138 code.
Note: Make sure that no add-on/aftermarket equipment is electrically connected to the APP signals or to the other ECM/PCM five volt reference or return lines. These can generate false P2138 and/or other ETC System DTCs. If there are other engine DTCs besides P2138, such as MAP sensor faults (i.e. P0107, P0108), resolve these first before attempting to diagnose P2138 DTCs.
Important: Refer to DTC P2138 in SI to confirm that the ETC pedal is operating correctly.
Locate the IP to body harness connector, which may be located in and around the left hand kick panel area or inside the IP. Check to see if there is a water leak into the area and repair as necessary. Use a water hose to determine the source of a water leak and effectiveness of repair. Some examples of potential water leaks are: A-pillar seals, sunroof drain lines (if so equipped) and windshield/cowl sealing. Finally, repair or replace the IP to body harness connector, making sure no corrosion or debris is left on or between the terminals.
Posted on Sep 07, 2010
Tips for a great answer:
May 17, 2013 | Volkswagen Jetta Cars & Trucks
Jan 23, 2013 | 2002 Volkswagen Jetta TDI
Dec 30, 2010 | 1995 Volkswagen Jetta
Mar 20, 2010 | 2005 Volkswagen Golf
Feb 27, 2010 | 2000 Volkswagen Jetta TDI
Mar 12, 2017 | 2003 Volkswagen Jetta TDI
Oct 29, 2008 | 2003 Volkswagen Jetta TDI
992 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: