Question about 1997 Volkswagen Eurovan

Open Question

How do I manually time up the injector pump on a vw transporter 2.5tdi 1999 t, where are marks on inj pump and crank or cam and what should they line up with, help would be most appreciated, cheers

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No spark 1999 volvo s 80 but has fire to inj..but wont spray


what have you actually got

no spark is from cam/crank position sensors faulty, faulty ignition control module
but you say fire to injectors -- do you mean power to injectors
if you have power but the injectors are not squirting---low /no fuel pressure = faulty fuel pump / no power to pump , faulty pressure regulator , pump relay problem
At this point check for a broken timing belt/ chain

Aug 13, 2016 | Volvo Cars & Trucks

1 Answer

Hi, how do I bleed the fuel system on a vw microbus 1997 model 2.5iand how do I know if my timing is correctly set I,


fuel pump working?
injectors spray?
put some fuel 3 spoons in the air inlet and crank the engine
should start for couple of seconds the ignition is ok.
good luck

Dec 04, 2014 | Cars & Trucks

1 Answer

I have a 1999 plymouth breeze and replaced water pump and timing belt due to pump locked up and all the teeth gone off belt now. 2.0 SOHC that after setting belt and timing correctly the car wont start...


In general, backfiring indicates the cam, crank and ignition are out of time or out of phase. The timing marks on the crank and cam just line up the timing of the cam and crank. The alignment of the spark with them has to be phased at the right time too. Check the manual for how to set the distributor timing after an engine repair

Nov 17, 2014 | Cars & Trucks

1 Answer

I was told u rotate the crank anticlocwise to the mark on the small srocket lines up with the timing mark then fit the cam belt with camshaft and injector on there marks but the no 1 piston is not tdc now


Don't worry about lining up no 1 atdc, if you line up the pump and cam and crank you will not have a drama, if those marks line up then go for it and fit the belt with the new tensioner,

Feb 15, 2014 | Mitsubishi Sigma Cars & Trucks

1 Answer

Wat are the timing belt marks for a 2000 5 cyl 2.5ltr petrol vw transporter


cam timing mark is on the back side of the cam view able through a small hole in the metal timing cover the crank shaft mark is on the transmission bell housing there is a opening that a -0- will line up to have an buddy turn the crank by hand and have a good light

Aug 08, 2011 | 2001 Volkswagen Eurovan

1 Answer

We need from pictures to timing belt cranctshaft and camshaft puley also inj.pump puley marks ,to change a new timing belt in ours Opel Corsa 1.7 TD .In advance things.e-Mail ,,vyvanov@yahoo.com


paint the gears with some white paint ,have a look and on this model you will the timing marks,they are 8mm holes on then cam and inj pump if i remember correctly ,they line up with a hole behind ,use a drill bit to lock in place

Dec 29, 2010 | Volkswagen GTI Cars & Trucks

2 Answers

Retiming of vw transporter diesel pump


hi there if you remove the cam pully wich drives the diesel pump you will see a key way in the end of the cam turn the engine untill the key way is flat ( i use a streight edge in the keyway and turn until it is level with the top of the cylinder head ROCKER COVER REMOVED once this is aligned up there is a mark o the back of the diesel pump pully thiss aligns up with a groove between two castings on the side of the pump at the front of the engine once all these are aligned up you can put on the belt ( it may ot start right away this wil be due to needing to bleed up the fuel ONLY IF PUMP BEEN REMOVED and bleeding up the fuel can be a right pain. hope thos helps ben

Jul 07, 2009 | 1993 Volkswagen Eurovan

3 Answers

Vw Transporter 2.5l T5 injector pump timing marks


below the cam gear on the side where your belt snapped is where the V notch that is an upside down cut away on the metal backing plate behind the gear nearest the cylinder head matches up with a cast block with a ball bearing in the middle in the 6 o clock position on the cylinder head. looking at it on the right side it is a cast almost machined straight edge up and down. On the left of the block it is something like C shaped. if you drew a circle and then on the right side cut one third of it off with a straight line, put a steel ball in the middle about 5 mm thick, that is the mark for the engine timing and you need nothing else, no TDC on the Crankshaft etc.

on the back of the fuel pump flywheel there is a key way type notch square looking cast into the wheel. it is about 2mm x 2mm in size.
this gets lined up with the cast aluminium mounting for the injection pump.
there is on the outer most point of the casting that the injection pump in mounted on a horizontal line cast into the very outer most point possible of the casting.
This horizontal line matches up with the key way type notch on the fuel injection pump flywheel.

It still needs to be timed but you wont bend any valves breaking the injection pump.

pratibha.

Apr 02, 2009 | 2001 Volkswagen Eurovan

2 Answers

Sprockets not alligned properly


IT TAKES SPECIAL TOOLS TO ALIGN INJ PUMP AND CAM SO BELT TIMING WILL BE RIGHT HAVE NEVER BEEN ABLE TO DO WITHOUT & AM VW TECH

Feb 19, 2009 | 1993 Volkswagen Passat

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8560 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...