Question about 1993 Nissan 300ZX

1 Answer

I have a 1992 nissan zx. It has power seats. the person b4 me unhooked the power to them. now i cant hook it back up. Under the seat is where he unhooked it. thanks

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

The connection should be hooked to a clip up under the seat ( i always have to unbolt the seat and flip it up to see where it is at)

Posted on Jul 31, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

How do you remove the DRIVERS seat


there should only be 4 bolts holding the seat, make sure to diconnect any wire connectors if you have power seats. click to see how to do it,
https://www.youtube.com/watch?v=gfJLSi90xes

Aug 16, 2014 | Cars & Trucks

2 Answers

Air bag is on after taiking seat out to clean


possibly pulled wire off sensor normally worked on weight so has to be wired under seat somewhere

Jun 01, 2011 | Volkswagen Jetta Cars & Trucks

1 Answer

How do you change out the seats in a 1983 nissan 280 zx


There are 4 bolts for each seat, I think the head of the bolts are 14mm. Two in the front running parallel to the floorpan and the two in the back are vertical. Remove those and the seat comes right out. Todd in Idaho

Feb 10, 2010 | 1983 Nissan 280ZX

1 Answer

Battery go dead after sitting for about 6 hours


first unhook the battery cable and wait 6 hours. If the battery is still charged when you hook it back up then start pulling fuses or relays. That car has so much electrical stuff it will take awhile to pin it down. One thing could be the seatcontrol box under the seat. It controls seat heat, power seats, memory seat. Do the power door locks work ok? A bad switch can drain the battery. How about rear leveling system. Leaky air shocks can make the pump run while the car is sitting. If you can't figure it out get a battery disconnect.

Jul 03, 2009 | 1997 Cadillac DeVille

1 Answer

Electric seats will only go one way


You need to check for power at the motor when you try to activate the switch. If there's power then you have a drive cable issue. If this is a manual seat then the problem is the actuator assembly itself,the cable,mechanism,etc. Remove the seat & take a good look at it. You'll see a problem,write back.

Jun 27, 2009 | 1985 Nissan 300ZX

1 Answer

Where is the BCM on a 96 sebring convertible


Behind your back seat cushion. You have to remove the seat to get to the hydraulic pump. to remove the seat you use a large screwdriver between your floor and the seat bottom at the front about a foot from each end. you will be able to tell that you cant pull the seat up as easily in two spots and you have to situate the screwdriver in those locations. Be careful not to break the seat or the bars, but sometimes you have to apply a lot of upwards force to get these two hooks to release. also you cannot put the screwdriver directly on top of the latch hook, the metal retaining bar doesnt continue through this area... place something under the side you unhook first to keep it from relatching in its slot. then do the other side. you then pull out the bottom of the seat, remove the two nuts holding the seatbelt latch bar on, and the back seat slides upward and comes right out.
There is a piece of sound dampening material with a black material on it covering up the location of the motor. once you lift this up the motor is right ther in the middle of the framing underneat the drain pan assembly.
i reccomdend putting your top down if possible to remove the back seat. it makes it a lot more comfortable to perform this task.

Jun 13, 2009 | 1996 Chrysler Sebring

2 Answers

I am trying to put seat covers on my back seats in my 1992 lexus


place a crowbar under the seats near the carpet and, pry up gently the car has clips under both sides of the center seats then: push down on the top of the seat back disengaging it

Apr 22, 2009 | 1992 Lexus Ls 400

2 Answers

Dont know were is the computer of my nissan 300zx


I have a nissan truck 96 and it is under the seat. but I have worked on maximas and they are below the radio under console. so I would check under seat but more than likely you are going to have to take out console too.

Dec 22, 2008 | 1992 Nissan 300ZX

4 Answers

2002 nissan maxima driver power seat will not incline


its not the motor its the switch to the seat...it happ. to me b4.

Sep 05, 2008 | 2002 Nissan Maxima

1 Answer

How to remove back seat to get into trunk of 1997 Grand Am


lift bottom section of the seat and remove the seat belt bolts and it will let the back slide up to unhook the hooks and remove it

Jun 28, 2008 | 1997 Pontiac Grand Am

Not finding what you are looking for?
1993 Nissan 300ZX Logo

Related Topics:

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...