Question about Chevrolet Camaro

1 Answer

I was looking for the blueprints on an 89 cammaro v6 2.8lt. an i need the blueprints on the trun signal switch and all lighting blueprints.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 24 Answers

You could go to the chevrolet dealer and they will print you one :)..hope i solved your problem :)

Posted on Jul 31, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No break lights are trun lights on the back of my 2009 chevy cobolt all tge lights are good what sould i do i was told the break light switch has went bad but would that stop tge trun lights


The stop lamps on your vehicle are controlled (turned on by the BCM ) - body control module ,turn signal lamps as well . Your vehicle doesn't have a normal brake light switch ,has a low voltage sensor , not to say they can't go bad .
Turn Signal Lamps
The body control module (BCM) is responsible for controlling the turn signals and hazard lamps. When the turn signal switch is placed in either the left turn or right turn position, the BCM receives a signal from the turn signal switch. The BCM then sends an on-off voltage signal to either the left or right turn signals and their instrument panel cluster (IPC) indicator. When the hazard switch is pressed, the BCM receives a signal from the hazard switch. The BCM then will send an on-off voltage signal to all the turn signal lamps. All the turn signal lamps will flash including both IPC turn signal indicators.
Stop Lamps
The body control module (BCM) is responsible for controlling the stop lamps. When the driver presses the brake pedal, the BCM will receive a signal from the brake pedal position sensor. The BCM then supplies battery positive voltage to both left and right stop lamp assemblies and to the center high mounted stop lamp (CHMSL). The stop lamps are grounded at G401 and G403. The CHMSL is grounded at G302.

The first step in the diagnostic process should always be to check for DTC'S - diagnostic trouble code's ,an follow a service diagnostic trouble chart ,testing electrical circuit's .Not listen to someone say it's the brake switch , because in most case's he has no ideal what he's talking about . I have 30 year's GM experience , the level of electronic's on your vehicle , most people just don't have a clue . Your best bet ,take it to a qualified repair shop . That doesn't mean the dealer either . A lot of good independent repair shop's out there .

Dec 10, 2017 | Cars & Trucks

1 Answer

Are the hazards and brake light and turn signals all connected, because none of them work. Parking lights work.


yes all go through trun signal switch.i would ck fuses for power to switch.

Mar 01, 2015 | Cars & Trucks

1 Answer

I have no brake lights in my gmc 1500 i have running lights trun lights turn signals and flashers


try to jump the brake light switch if that does not work check for power at switch if no power and fuse is ok may need new turn sinal switch if you have power at switch and when you jump it you have no lights check at the rear for power if you have power check ground

Sep 18, 2014 | GMC Sierra 1500 Cars & Trucks

1 Answer

89 Chevy 1500. Break lights and rear turn signals quit working ... I'm clueless. Help?


Since power from the brake light switch goes thru the turn signal switch, have you checked the turn signal switch for power in and out on each circuit ?

Jun 01, 2013 | Cars & Trucks

1 Answer

How come my signal lights only work on the right side of my1999 dodge durango?


I had this problem, I needed a new trun signal relay switch, and that solve my problem.

Jun 29, 2011 | 1999 Dodge Durango

2 Answers

1990 Cadillac Fleetwood Left turning light or emergency lights go on but don't flash. The right turning light flashes well. If I turn the handle not all the way left and move it a bit the left light begins...


You most likely need a new blinker switch - the emergency flasher is also most likely bad - there is one flasher for turn signals - and one for the emergency lights --
Replacing a blinker switch is best left to the pros --
also - Take down the Vin # and call the local dealer - - ask about recalls and Service bulletins.

Dec 28, 2009 | 1990 Cadillac Fleetwood

2 Answers

96 VW Cabrio Turnsignal wont stop flash at a high rate of speed


This could be a flasher or a relay problem. You will have to trace the wiring to find relay. Flasher should be on or above fuse box .

You can go to autozone.com and register for full free online repair manual

Sep 16, 2009 | 1998 Volkswagen Beetle

1 Answer

Turn signals don't work on '89 taurus gl. Fuse is good, flasher is new. I tried a different turn switch on the column but still nothing. Wiper, washer and highbeams work on the switch just not the trun...


still sounds like the multi-function switch on the column. If you have old one, take apart and look for discolored coating on copper strips. clean with emery cloth and add di-electric grease.

Jun 30, 2009 | 1989 Ford Taurus

1 Answer

98 lumina brake lights and rear turn signals stopped working.


A flasher would not cause this problem, It's in the trun signal switch, it needs to be replaced

May 30, 2009 | 1997 Chevrolet Lumina

2 Answers

1989 Jeep Cherokee - Electrical Problem - horn, brake lights, blinkers, radio/cd...


I think I have found the problem. When I wiggle the ignition switch the turn signals and radio go on and off so I feel the issue is in the ignition switch. From what I understand the actual electronics for the switch are at the base of the sterring column behind the lower dash panel and is connected by a rod that may need adjusting.

Aug 14, 2008 | 1998 Jeep Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

203 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...