Question about 2002 Toyota Camry

Open Question

Install egr valve for2002 Camry v6 automatic - 2002 Toyota Camry

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1861 Answers

SOURCE: 1997 Camry Valve Cover Gasket Replacement

Removal of the plenum is pretty straight forward. You will need to replace the plenum gasket after you remove it; the gasket is not reusable. Personally, if I was going to take the trouble to remove the plenum, I would replace the plugs and wires back there, also.
I know, I have a 93 Camry V6, and it is a real pain to do the plugs and wires with the plenum on. There are no secrets or great tips on the plenum removal, just take your time. Remember that there are different size bolts, and where they go. Please get back to me if you need any more info...Hope this helps, and thanks for choosing FixYa to resolve your issue.
The graciousness of a FixYa rating for my assistance would be greatly appreciated.

Posted on Dec 15, 2008

Ad
  • 16 Answers

SOURCE: How to replace EGR valve on 2000 camry V6?

If you have a P0401 code from a CEL, the first thing is to check the EGR vacuum modulator. It is a little well usually next to the EGR. Pop the cap off and dust the little sponge inside. Sometimes this gets stuffed up with carbon particles and causes recirculation problems. You should clean the tubes hooked to it while you are there. Reset the code and see if the light comes back.

Replacing the EGR is not a tidy job. It is an expensive part to replace and you will disconnect the three hoses and dismantle it from engine by two nuts. Save it for the later if the previous trick fails to work.

Posted on Jan 19, 2009

  • 333 Answers

SOURCE: WHERE DO I LOCATE THE EGR VALVE ON MY 2001 CHEVY IMPALA 3.8 V6

The egr valve is located at the end of a hose that plugs into youe valve cover. It is pushed right into a rubber grommet that is located in one of the valve covers. I hope this helps. don.t forget to rate my nswer, thanks

Posted on Feb 27, 2009

  • 14 Answers

SOURCE: Code P0401 toyota Camry 3.0 v6

replace the vsv that has the vacuuum hose running from it to the egr valve

Posted on Jun 05, 2009

kel1guy2002
  • 3740 Answers

SOURCE: How to clean EGR valve passages in 1993 Isuzu Trooper DOHC V6

You have to the EGR valve (sometimes the Intake manifold to EGR Vlalve line also). After you remove it take a drill bit the about 20 % smaller than the actual hole of the outlet side and rotate the drill bit with your hand to dig out the carbon. Aditionally the line coming from the intake manifold to the EGR valve will clog near the connection to the EGR valve. I use either a single piece of copper wire or the wire that you would use to tie ribar together to clean the line. When your done cleaning take a piece of vacuum line and connect it to the diaphram side and **** on it... then plug the line well with your thumb. Grasp the valve and blow thru it... Air should blow thru it freely. Remove your thumb from the vacuum line and try blowing again.. No air should pass thru the valve.
Then reinstall the valve and start the vehicle with the vacuum line disconnected (but blocked off) Use another piece of vacuum line connected to the diaphram again and **** on the line.. The vehicle should die or run really bad. If it does this then you cleaned it correctly.

Posted on Jan 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I fix code P402 on the 1998 V6 3.0L Toyota Camry XLE?


That is "Exhaust Gas Recirculation Flow Excessive Detected". The EGR valve may be gunked up or stuck open, so remove and check that. It may also be that the VSV (vacuum switching valve ) connected to it has failed. In Toyotas these little solenoid valves sometimes fail when hot but test OK when cold.

More info is here

http://www.turboninjas.com/camry/eg2.pdf

Sep 26, 2014 | 1998 Toyota Camry

1 Answer

Fuel cal-pak incorrect or missing


52 is a faulty knock sensor signal. The connection there may be loose or broken. 71 is an EGR temperature signal fault. Again the connection may be loose, or the EGR temp sensor faulty, or the EGR vacuum switching valve faulty.

May 10, 2014 | 1993 Toyota Camry V6

1 Answer

Failed emissions got p0301,p0402 please help


V6 or 4cyl????
P0301- #1 cylinder misfire -Old/Fouled Plugs -Faulty spark plug wires/distributor or rotor (4cylinder only) -Faulty cam/crank sensor (v6 only) -Faulty #1 ignition coil or coil electrical connector (V6 only) -#1 Compression loss
P0402- EGR Issue A code P0402 most likely means one or more of the following has happened:
  • The DPFE (differential pressure) sensor is faulty and needs to be replaced
  • There is a blockage in the EGR (most likely carbon buildup)
  • The EGR valve is faulty
  • The EGR valve may not be opening due to a lack of vacuum

Jun 07, 2011 | 1996 Toyota Camry

1 Answer

Need to find out were the dpfe sensor is on my 1999 toyota camery with a v6 it has a code po402 and they say to check this sensor first


p0402 is egr valve flow excessive. egr valve needs cleaned or replaced also check wires etc. to vavle.

Apr 22, 2011 | 1999 Toyota Camry

1 Answer

Where do I hook up the lower metal tube on the egr valve ( right hand side egr valve) thats on my 1992 toyota camry 4 cylinder?


You connect it to the metal-tube under the EGR vacuum modulator. Vacuum modulator is behind the throttle-body manifold, and it is black. small-can like appearance.

Nov 01, 2009 | 1992 Toyota Camry V6

1 Answer

Need to find location of egr sensor


A 2000 Camry with a 4cyl does not have a EGR sensor. The ECU uses the readings from the MAP and AF sensors to determine if the EGR is working.
You have a EGR VSV (vacuum switching valve) and a EGR modulator but no position sensor. Only the V6 has this.

Apr 02, 2009 | 2000 Toyota Camry

1 Answer

Code P0401 toyota Camry 3.0 v6


replace the vsv that has the vacuuum hose running from it to the egr valve

Feb 21, 2009 | 1998 Toyota Camry

2 Answers

2000 toyota camry v6 code p0402


The egr valve on that motor has a egr positioning sensor mounted on top. The sensor goes bad and the ecu can't determine the how far the valve is opening so it opens it too much. This causes surging of the engine under light throttle application. Also as stated above the egr can stick causing rough idle. Either way if you get the valve from the dealer it will come with the sensor solving both your problems.

Dec 23, 2008 | 2000 Toyota Camry

1 Answer

How to replace EGR valve on 2000 camry V6?


If you have a P0401 code from a CEL, the first thing is to check the EGR vacuum modulator. It is a little well usually next to the EGR. Pop the cap off and dust the little sponge inside. Sometimes this gets stuffed up with carbon particles and causes recirculation problems. You should clean the tubes hooked to it while you are there. Reset the code and see if the light comes back.

Replacing the EGR is not a tidy job. It is an expensive part to replace and you will disconnect the three hoses and dismantle it from engine by two nuts. Save it for the later if the previous trick fails to work.

Aug 20, 2008 | 1999 Toyota Camry

3 Answers

Difficulty to replace EGR valve in 1999 totyota camry 4-cyl automatic


Not difficult at all to service the EGR Valve using a #12 mm socket wrench it is a five minutes job. However the VSV is another history and very difficult to be reached unless you have an elevator After the engine begin stalling I double checked the EGR which was completely carbonized. I cleaned it and also replaced IAC checked VSV and all sensors, but the engine follows stalling. Now I am looking for the Charcoal Canister which I simply can't find where it is located, then I will check the vacuum lines and the transmission sensors, but I have heard that EGR despite cleaned can keep bringing troubles. By the way, anyone has ever heard where in the car is installed the charcoal canister

Jun 17, 2008 | 1999 Toyota Camry

Not finding what you are looking for?
2002 Toyota Camry Logo

Related Topics:

178 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

Marvin
Marvin

Level 3 Expert

85020 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...