Question about 1998 Chevrolet S-10 Pickup

1 Answer

I have a remote doorlock and hatch unlock from a 1996 blazer can it be programed for a 1998 chevy blazer if it can how do i program it

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Chevrolet Master
  • 426 Answers

There is a number on the back of the key fob you would have to see that it is the same number for both for it to work. it is a very small print number. you could call a gm parts department and they could give you details on the part number if you dont have original one so you can see if the one you do have matches

Posted on Jul 30, 2009

Testimonial: "VERY GOOD INFORMATION"

  • Donnie Matney
    Donnie Matney Jul 30, 2009

    Important: Different keyless entry systems are used on General Motors vehicles. The parts are not interchangeable even though the parts may appear to be similar. Observe the back of the transmitter in order to properly identify the system. On 1998 S/T pickups and utilities, use a transmitter identified with GM/UTA preceding the part number.


    1. With the driver door closed, hold down the power unlock button on the door panel.

    2. Turn the ignition switch to the ON position.

    3. Turn the ignition switch to the OFF position.

    4. Turn the ignition switch to the ON position.

    5. Turn the ignition switch to the OFF position.

    6. Release the power unlock button on the door panel.

    7. The remote control door lock receiver will respond in the following manner in order to indicate that the receiver is in the programming mode:





      6.1.
      Locking the doors




      6.2.
      Unlocking the doors
      Important: All extra transmitters must be programmed at this time. When a new transmitter is programmed, it will deactivate the old transmitters.

    8. Hold down the lock and unlock buttons on the transmitter until the remote control door lock receiver will respond in the following manner:





    9. 7.1.
      Locking the doors.




      7.2.
      Unlocking the doors.
    10. Repeat step 7 for each additional transmitter.

    11. Turn the ignition switch to the ON position in order to exit the transmitter programming mode.

    12. In order to reprogram the remote control door lock transmitter with a scan tool, refer to Scan Tool instructions.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Key fob


Walk out to the vehicle with a new battery in the key fob and press the lock AND unlock button at the same time while you stand close to the vehicle for 7 seconds. You will hear the doors go thru a lock and unlock cycle, your fob is now programmed. This will sync existing programmed controllers, security sync. to program new remotes:In the trunk, connected to the wireless remote controller (driver side on wheel well, need to remove 'mat') is an empty connector with 2 wires connected. short the two connector pins. The locks will all cycle. Press and hold lock/unlock buttons on remote until locks cycle on/off. repeat for other remotes. Remove short across connector pins. Test new remote(s).Warning:existing remotes are deprogrammed, only remotes programmed will work from now on.This worked on my 1998 Cavalier. Be sure battries in new remote(s) are good! Answer Locate the data link connector under the dash (under the steering column). Ground out pin #8 of the DLC (top right port) with a jumper wire to any piece of metal close by (I use the e brake hardware). The door locks will then lock & unlock to let you know you are in the programming mode. Simultaneously press & hold the lock & unlock button on one of the keyless entries until the locks cycle (this lets you know the transmitter has been programmed). Repeat this step for your second transmitter. You must reprogram the 2nd transmitter within 60 seconds of programming the 1st one or you have to start over.
Note

Read more: http://wiki.answers.com/Q/How_do_you_program_a_keyless_remote_for_a_1996_Chevy_Tahoe_LT#ixzz1wjwEcG4s

Jun 03, 2012 | Oldsmobile Cutlass Supreme Cars & Trucks

1 Answer

How to unlock a 1983 chevy blazer without a key?


Use a Slim-Jim opening tool. Depending on the weather stripping, it may also be possible to use a coat hanger to grab the inner door handle and pull it open.

Use your Autoclub memberships, Insurance company memberships to get help. A locksmith has MASTER keys to fit in the doorlocks. The Locksmith comes out with a box of Masters for GM trucks and inserts them one-byone into the doorlock until he finds the right one.

Jan 23, 2012 | 1983 Chevrolet Blazer

1 Answer

Can't find the keyless remote module under steering column to reprogram my remotes 1195 Chevy Blazer


Here is what i found for your 95 blazer. Hope it helps a little bit.

1. Locate the red two wire programming connector located near the central
locking control module. Behind LH lower instrument panel.

2. Inside the red programming connector you will see two pins.
Jump the two pins with a section of wire. A paper clip bent in a "U" shape will also work.

3. System should now lock and unlock doors to indicate vehicle has entered
programming mode.

4. Press any button on keyless remote once. System should now lock and unlock
doors indicating the keyless remote has been programmed.

5. Repeat step 4 to program the other remote.

6. Remove jumper wire from programming connector to exit programming mode.

7. Test Remote(s).

Sep 02, 2011 | 1995 Chevrolet Blazer

1 Answer

On my 1996 chevy blazer the hatch won't unlock


It should be number 2 in the fuse box but if you can still hear the motor when you push the button than you need to try and pull the top where the lock that holds the glass hatch pull the plastic far enough to get you hand in on the right side of the latch and you will find a lever that you should be able to push to your left I believe and that will release the glass hatch and than open the tail gate take off the plastic inside cover and unscrew the metal plate off of the inside of the tail gate and you will be looking for a blue plastic piece that supposed to be connected to the release motor and the latch if thats broken than you need to go to the auto wreckers find a blazer or jimmy from '95-'97 maybe all the way up to 2000 I believe and basicly do the same remove the blue clip from that one put it on yours and it should work and if the clip on your is broken dont try to glue it, it wont work I tryed everything to try and fix it on mine but you have to get another one once you find another clip it doesnt really take long but yea anyways I hope that helps you out let me know heres my email THUNDERSTRUCK_244@hotmail.com

Mar 26, 2010 | 1996 Chevrolet Blazer

1 Answer

95 S10 blazer 4dr power door locks inop, new battery installed in remote, all fuses good, still inop?


1. Locate the red two wired programming connector located near the central locking control module that is located behind LH Lower instrument panel. Drop the panel and you will see the red programming connector that is not connected to anything.
2. Inside the Red programming connector you will see to pins..
Jump two pins with a section of wire.
3. System should now lock and unlock doors to indicate vehicle has entered programming mode.
4. Press any button on keyless remote once. System should now lock and unlock doors indicating the keyless remote has been programmed.
5. Repeat step 4 to program other remote.
6. Remove jumper wire from programming connector to exit programming mode.
7. Test Remote(s)

Dec 22, 2009 | 1995 Chevrolet Blazer

1 Answer

I have a 96 chevy blazer 4.3 l 2wd 4 d how do i program key fob


1. Locate the Data Link Port. It is located under dash drivers side. Be sure you know which pins are 8 and 4.

(Notice port is wider on top row)

obd-1.jpg







2. Make sure there are metal contact pins in terminals 8 and 4. Connect 8 to 4 with a suitable
jumper wire (leave the jumper wire connected throughout the programming procedure). Make
sure you know which terminals are 8 and 4. The vehicle will respond by locking and unlocking the
doors to signify entering of programming mode.
3. Press and hold both the LOCK and UNLOCK buttons together on the first transmitter to be
programmed. After about 15 seconds, the vehicle will respond by locking and unlocking the doors.
Release the buttons on the transmitter.

4. Within one minute, repeat the previous step on the remaining transmitters to be programmed.
5. Remove jumper wire applied to the OBDII Port.


Good luck and this should work.

Dec 14, 2009 | 1996 Chevrolet Blazer

2 Answers

Program fob


Instructions to program a keyless entry remote for a Chevy Silverado. They also work on 2003, 2004 and 2006 Suburbans.
  1. Close all the vehicle doors.
  2. Insert the ignition key into the ignition lock cylinder.
  3. Press and hold the DOOR unlock switch.
  4. While holding the DOOR lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
  5. Release the DOOR unlock switch. The doors will lock and unlock to confirm the program mode.
  6. Press and hold the LOCK button and the UNLOCK button simultaneously on one keyless remote. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of that transmitter.
  7. Repeat the previous step to program up to four transmitters.
  8. Turn the ignition switch to the RUN (one more click forward) position in order to exit the keyless entry transmitter mode.
  9. Operate the transmitter functions in order to verify correct system operation

Apr 19, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

How to program the keyless entry for my 1996 Acura TL.


Hi, Stacie,

here's the instructions for a 97 TL - I hope they're the same.

Note:
Entering the programming mode cancels all learned keyless remotes, so
none of the previously programmed remotes will work. You must reprogram
all of the keyless remotes once you are in the programming mode.
You must complete each step within 4 seconds of the previous step to keep
the system from exiting the programming mode. You must program remotes
within 10 seconds of each other

1. Turn ignition switch to ON (II)
2. Within 4 seconds press the LOCK or UNOCK button on one of the remotes.
(An unprogrammed remote can be used for this step.)

3. Within 4 seconds turn ignition switch to LOCK (0) position
4. Within 4 seconds turn the ignition switch to ON (II)
5. Repeat steps 2, 3 and 4 two more times using the same keyless remote
used in step 2

6. Within 4 seconds press the LOCK or UNLOCK button on the same remote.
Make sure the power door locks cycle to confirm you are in programming
mode.

7. Within 10 seconds press the LOCK or UNLOCK button on same remote.

8. Within 10 seconds press the LOCK or UNLOCK button on all other
remotes you want to program. Make sure door locks cycle after you push
each remote button to confirm system has accepted the remote.

9. Turn the igniton switch to LOCK (0) to exit programming mode.
10. Test remote(s)

Hope this helps :)

John

Mar 26, 2009 | 1998 Acura TL

1 Answer

Reprogram keyless entry


It took me a few attempts to program a new keyless remote for my 2002 Chevy Blazer.
Insert key into ignition but don' turn it yet. While holding down the UNLOCK switch on the door, the trick is to cycle the ignition ON OFF ON OFF as quickly as possible then release the UNLOCK switch. If done correctly the door locks will cycle 1x to acknowledge. Then hold both the unlock and lock buttons down on the remote for about 15 seconds. The locks should cycle again to confirm...Hope this helps.

Mar 19, 2009 | 2002 Chevrolet Blazer

Not finding what you are looking for?
1998 Chevrolet S-10 Pickup Logo

140 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...