Question about 2004 Pontiac Sunfire

1 Answer

When I put on my turn signals especially the right one, the fuse will blow after once or twice and the Back up lights will no longer work. Need a Wiring diagram for a 2004 Pontiac Sunfire. PS I am broke and can't afford anything but fuses please help.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 24 Answers

Hmmm....u might have the wrong kind of fuse in it..i think the lights take a 20 not a 15..or even a 40..posibility..hope i solved your problem :)

Posted on Jul 31, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1987 ford ranger turn signals keep blowing fuses. have changed flasher fuse and switch on column. just keeps blowing?


first thing i guess to understand what is going on here ,is a little back to basics on how turnsignals work , first item you have is power fuse then it's off to flasher module than it goes to the turnsignal switch on colum ,of course anywhere on it way to there the power could got to ground and cause the fuse to trip, now the power depending on Left or right selection , is directed to lights on both front and back of truck,thankfully rangers don't have em on the side) now any place in this pathway the wire could go to ground and blow the fuse, now to troubleshoot and narrow down the area that fault is located , (1) replace fuse with correct size and ck for proper fit in fusebox and start and operate truck for a few minutes DO not use turnsignals, ck fuse is it still good if so go to step 2 if not stop and ck wire conditions in steering colum and switch(2) start truck and try right hand turn signal only verify lights working ,Ok yes/no if not replace fuse and try left side same way, Ok yes /no if right or left side only blows fuses take ALL bulbS OUT of lights and try again , if fuse still blows then look for wire fault on that side of truck if fuse is still good then look carefull at light bulb sockets for rust and powered corrosion (ill bet an 87 has some ) you may need to replace bulb sockets , they do sell em in autoparts stores .

Jun 30, 2014 | 1987 Ford Ranger

1 Answer

Brack lights wont light up on my 1988 ford ranger we keep blowing fuse and put in new brake switch


If you keep blowing the brake fuse than you have a short in the system. Unplug the brake switch. Install a new fuse. If it did not blow than the problem is after the brake switch. Next unplug the turn signal switch, then plug the stop light switch back in and press the brake pedal. Did the fuse blow. If not than the wiring is good in between the two switches. With the turn signal switch disconnected use a jumper wire in between the light green wire (power from the brake switch) and the orange with light blue wire (power to the right brake lamp). If the fuse blows than there is a short in the right side brake circuit between the plug in and the rear socket assembly. If the fuse does not blow than jump from the light green wire to the Light green with orange wire (power to the left brake lamp). If the fuse blows than the problem is in the left hand brake wiring circuit.

Sep 04, 2013 | Cars & Trucks

1 Answer

2003 honda element fuses blown


One more thing to check , an it's the Main Fuse , it should be either 100 or 150 Amp fuse , ill be back at work Monday and ill check it in my wiring diagram . Usually this Fuse blow up when jumping a car incorrectly or mistakenly touching the terminals together . So I would check the big fuses first . Also why spend 600.00 at the dealer for a cluster when you could find one with a same or close mileage at Ebay for a fraction of that's .

Jan 13, 2013 | 2003 Honda Element

1 Answer

How can I figure out why fuse 15A keeps blowing? My dashboard lights don't work nor do the back lights. My breaks and signals work but at night when I turn the car on the regular lights in the back...


There is a shorted wire somewhere in that circuit. Check to see if any wires are pinched under a bracket or brace where he was working. I have seen it where it was a light bulb the was bad. Need someone familiar with a volt/ohm meter to help trace problem. Good Luck. You did not state where he had been working.

Apr 17, 2012 | 1996 Honda Accord

1 Answer

My left turn signal no longer works on my '00 T&C. Hazards, brakes and right turn signal works. I've replaced both lights in front and back, replace turn signal switch and check fuses'. What else can I...


SOUND LIKE WIRE PROBLEM.YOU NEED A WIRE DIAGRAM TO CHECK THE TURN SIGNAL SWITCH WIRING DONT PLUG A WIRE IF YOU DONT KNOW WHERE IT GOES COULD CAUSE ELECTRICAL BLOW OUT.TRY TO GO ON LINE LOOK FOR AUTODATA DIY COM LOOK FOR ELECTRICAL DIAGRAM.

Nov 18, 2010 | 2000 Chrysler Town & Country

2 Answers

In the park position, the turn signal works, but w...


There has to be a short or a crossed wire in there somewhere.

You handy with a multimeter?

Check voltages/shorts at the fuse box when the turn signal is on and off while having someone switch the car from park to drive. i'm guessing it's caused by a short or something in common with putting the brake on (because putting the car in drive requires you to apply the brakes first, causing the brake lights to come on, possibly overloading the fuse for the turn signal)

Also check the inside of the area where the signal bulbs are, could be crossed with the brake or shorted in there somewhere.

The bulbs also might have something in common internally, replace the bulbs if you haven't already. I think those bulbs can come on from a signal from the brake pedal (brake lights), but can also be activated by the turn signal.

Good luck with that, let me know how it turns out or if there are any developments

May 19, 2010 | 1987 Pontiac Fiero

1 Answer

97 Sebring blowing turn signal fuse. I believe this is a common problem. The flasher and turn signal blows the # 6 fuse ( 20A). I fixed it once by larger amps. Is there a cause and fix


sounds like you have a short in your turn signals
(tip 1) replace the fuse with a 20 amp breaker instead of a fuse if it is a intermitant short it should reset instead of going out completly
(tip 2) before you put the breaker in put a fuse back in and try to make note which direction you are trying to signal when it blows this may help you isolate the short it will at least tell you the side of the car the problem is at unless it is under the dash if it turns out to be in wires to sockets which is common problem area .chances are great all you will have to do is check light sockets and wires to them on that side of car front and back.good luck and i hope this helps
mrdmburns@cableone.net
feel free to contact me via email if you are unable to locate short.

May 05, 2009 | 1996 Chrysler Sebring

1 Answer

Fuse for trailer right turn signal and brake blows intermittently


abad ground on that tail light unit could affect current load when turn and stop are used simultaneously. Although one side only is affected make sure of good grnd between trailer and tow vehicle. focust on the tail light unit in question. Replace the bulb. though rare, bulbs have been known to be the problem. If the bulb is breaking filiments ck the filiment orientation. filiments last longer in vertical orientation, where horizontal permits vibration to break the heated filiment when brake is applied.. good luck and let me know if This helped or not.

Apr 26, 2009 | 2003 Chevrolet Silverado 2500HD

Not finding what you are looking for?
2004 Pontiac Sunfire Logo

269 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...