Question about 2004 Jeep Grand Cherokee

1 Answer

What procedure do I follow to replace the timing belt, pulleys & tensioner on a 2003 2.7CRD Jeep Grand cherokee

Posted by on

  • Richard Scordino May 11, 2010

    Don't remember a 2.7 Jeep engine, and never saw one with a timing belt...they all have timing chains.

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 86 Answers

HI. THIS IS WHAT I WOULD DO. I WOULD GO AND BUY A (HAY'S REPAIR MANUAL) YOU CAN BUY THEM AT ANY AUTO PARTS STORE. JIMBO

Posted on Aug 05, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Serpentine belt keeps coming off a jeep grand cherokee.. What could be the cause?


Misaligned pulley , seized tensioner , weak tensioner spring . Do you hear any squealing ? Locked up A/C compressor . Have you replaced any parts lately ? Alternator , water pump etc..

Jun 21, 2016 | 1996 Jeep Grand Cherokee

1 Answer

I have a 1996 jeep grand Cherokee. It runs fine except for the squealing belt! Just replaced the water pump and the belt and it's now worse than it was before! Any ideas? I checked the auto tensioner...


You have an out of alignment belt run across the pulleys of the engine, this causes the belt to make noise as it rubs on the edge. Many times this is causes by the crankshaft vibration damper coming part and the pulley walking outward.

Feb 21, 2012 | 1996 Jeep Grand Cherokee

2 Answers

I need a diagram for the serpentine belt for a 5.2L engine on a 1997 Jeep Grand Cherokee


1997 JEEP GRAND CHEROKEE - V8 5.2L 318ci GAS FI N Y
Usually the label diagram is underhood, over radiator/grille..
.

zjlimited_353.jpg



If you need more details about youe Jeep ZJ Grand Cherokee, can check this documents about Repair Manual: Grand Cherokee 1993-1998 FSM

To get out, it's easy and doesn't require a prybar.
  • Get a 14mm or 9/16" socket and a long handled ratchet or breaker bar.
  • Get the belt around all the pulleys except the A/C compressor or Alternator.
  • The tensioner pulley is near the Alternator toward the center of the engine. It's on a spring loaded arm. Get your socket on the center nut of this pulley.
  • Slowly pull the ratchet toward the center of the engine. The pulley will pivot on the arm allowing you to get the belt on the final pulley.
  • Slowly release the tension.
  • You're done

Hope helps (remember to rate this answer).

Dec 29, 2010 | 1997 Jeep Grand Cherokee

1 Answer

Hello, how to relieve the belt tension on jeep grand cherokee 1995?


Hi,


In order to relieve the belt tension in your cherokee jeep,you have to locate the belt tensioner pulley first, which is found between the crankshaft and a component toward the top of the hood area.

Afterwards,Rotate the belt tensioner pulley, using a wrench spanner to relieve the tension on the belt.



Good luck.

Aug 20, 2010 | 1995 Jeep Grand Cherokee

2 Answers

How to adjust de belt to grand cherokee 8 cilinders 4.7


  1. Step 1 Find the belt tensioner pulley. The tensioner pulley is generally between the crankshaft and a component toward the top of the hood area.
  2. Step 2 Check the belt routing so you know how to replace the belt. You may be able to find a belt routing diagram on a decal on the fan shroud or in support documentation. Otherwise, make you own sketch for reference.
  3. Step 3 Rotate the belt tensioner pulley, using the wrench, to and relieve tension on the belt.
  4. Step 4 Slip off the old belt and slowly release the tensioner pulley.
  5. Step 5 Use your belt routing diagram to put the new belt onto all of the pulleys. Pay close attention to the water pump pulley, as incorrect routing can cause the water pump to run backwards and overheat.
  6. Step 6 Make sure the belt is correctly routed and seated on all pulleys. Rotate the tensioner again to allow for the belt to slip onto all pulleys and then release the tensioner again to regain correct tension on the belt.

Jun 01, 2010 | 1999 Jeep Grand Cherokee

2 Answers

Drive belt came off pulley loose on 2007 jeep grand laredo


The center pully is the IDLER PULLEY.
It is also referred to as the TENSIONER.

It has a coiled spring that creates the belt tension. Replace it ($15) (and the belt) ($8).

Hope this helps!





Sep 04, 2009 | 2007 Jeep Grand Cherokee Overland

1 Answer

1998 Jeep Grand Cherokee - Multi-rib belt Removal & Replacement


Check on upper rad shroud or under hood for routing diagram. Depending on what engine, procedure may vary a little. I wouldn't panic on replacing anything other than belt unless you noticed something noisy under hood in last while.
If not up to it, a mechanic should be able to do it for you in a few minutes usually, but won't hurt to ask before, just in case.

Jun 27, 2009 | 1998 Jeep Grand Cherokee

2 Answers

How do i change a Timing Belt Tensioner on a 1995 jeep grand cherokee v8 5.2 my belt burned in 2 it and i need 2 take it off n replace it


You really need a repair manual for your model. Most Auto parts stores carry these. However, If your timing belt has been broken (burnt) while the vehicle was running, then you'll need to check for bent valves or cracked pistons. If you are not one, you may need a mechanic.

Jun 01, 2009 | 1995 Jeep Grand Cherokee

1 Answer

2000 jeep grand cherokee 4.0 liter engine timing belt replacement


If you have the same pulley arrangement that most 4.0 engines have that pulley is an idler not a tensioner. Your power steering pump has a pivot bolt, and a slide under the pump. You adjust belt tension using the pump.

Apr 04, 2009 | 2000 Jeep Grand Cherokee

3 Answers

The belt keeps coming off the fan


the only reason for the belt coming off the pulley is the something in the belt path is off aligment.
put the belt back on and chek the path where the belt pass. water pump, alternator, AC compressor, Power steeling unit, etc....... or even the pulley tensioner itself.
chance are there is a belt in the wrong pully slot.

Nov 10, 2008 | 1996 Jeep Grand Cherokee

Not finding what you are looking for?
2004 Jeep Grand Cherokee Logo

154 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...