Question about 2005 Chrysler Town & Country

1 Answer

How do you remove the cover of the rear drum brakes?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 206 Answers

Not sure of particulars of this vehicle, but normally you must:

1. properly jack & support vehicle.
2. cannot have the emergency brake on, as this will prevent removal.
3. Remove tire.
4. Often, if this is the first time to remove, must remove some small retaining clips on the threads of the lugs. These are for factory shipping only, I usually destroy them in removal & discard.
5. Slide the drum off. Sometimes it requires the drum to be gently worked off if the brake shoes are in close contact with the drum.

Posted on Jul 30, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace the rear wheel hub on a 2003 Kia sedona. All I can find is directions on front not back.


Wheel Bearings

Print
Adjustment

2002-05 Models
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:

    Rear wheel Brake drum Hub cover Cotter pin Lock nut cover
  3. Adjust the locknut to achieve wheel bearing play of 0.001-0.006 inches (0.025-0.152 mm).
Removal & Installation

2002-05 Models
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:

    Rear wheel Brake drum Hub cap Cotter pin Lock nut cover Lock nut Wheel bearing retainer washer and the outer wheel bearing Hub assembly Grease seal Inner wheel bearing
  3. Clean and inspect the wheel bearings and races for unusual wear or damage. Replace parts as necessary.
To install:
  1. Pack the wheel bearings with grease for assembly.
  2. Install or connect the following:

    Inner wheel bearing Grease seal Hub assembly Lock nut. Adjust the locknut to achieve wheel bearing play of 0.001-0.006 inches (0.025-0.152 mm). Lock nut cover Cotter pin Hub cap Brake drum Rear wheel

Apr 03, 2015 | 2003 Kia Sedona

1 Answer

Brake shoes on 1987 f250 460 1987 2 wheel drive how to replace


Lift the front of your Ford F-250 off of the ground using a jack and jack stands. Remove the wheels from the Ford with a lug nut wrench to prepare the truck for servicing. 2 Open the hood on the engine compartment and take the lid off of the master cylinder that bolts to the brake assister on the driver's side firewall.3 Remove the hex-head bolts on the back of the brake caliper with a socket. With the bolts removed, pull the caliper off of the Ford's brake rotor.4 Pull the old brake pads out of the caliper and discard them. Squeeze the brake piston back into the backside brake caliper with pliers, and then insert the new pads into the brake caliper.5 Pull the rotor cap cover off the middle of the rotor with a screwdriver and use a socket to remove the nut located behind the cover.6 Pull the rotor off of the wheel spindle.7 Remove the old wheel bearings from the brake rotor and insert them into the new rotor. If the old wheel bearings are worn, replace them with new bearings.8 Slide the new rotor onto the wheel spindle and secure it using a bolt and socket. After you tighten the bolt, press the cover back onto the rotor.9 Place the caliper on the rotor and secure it with a socket and hex-head bolts. 10 Duplicate the process on the passenger side of the F-250. 11 Close the master cylinder after putting the wheels back on the Ford and lowering it to the ground. Press on the brake pedal to seat the pads against the rotor
Replace the F-250's Rear Brakes 1 lift the rear of the Ford F-250 off the ground with a jack and jack stands. Remove the wheels from the Ford with a lug nut wrench.2 Place a strip of paint on the back of the brake drum and rear brake drum cover so you can position the brake drum orrectly when you put it back on. If you plan to install new brake drums on your Ford F-250, skip this step. 3 Place the brake drum puller on the brake drum and pull the drum from the wheel hub. The method for attaching the brake drum puller depends on the brake drum puller that you use. 4 Remove the springs that attach the brake shoes to the wheel hub by pulling them off with pliers.5 Lift the old brake shoes off of the wheel hub and place the new brake shoes on the wheel hub. Secure the new shoes with the springs.6 Pound the brake drum onto the axle hub with a rubber mallet.7 Duplicate the process on the passenger side of the Ford.8 Put the wheels back on the F-250, lower it to the ground and, then press on the brake pedal to seat the shoes against the brake drum.

Oct 14, 2011 | 1988 Ford F 250

1 Answer

I have a 2000 suziki grand vitara and cant furure out how to remove the rear drums


  1. Raise and safely support the vehicle.
  2. Remove the rear wheel(s).
  3. Release the parking brake.
  4. Remove the parking brake lever cover screws and loosen the brake cable locking nut.
  5. Install 2, 8mm bolts into the brake drum holes and uniformly tighten each bolt. Tighten each bolt until the brake drum is removed from the vehicle. If there is difficulty in removing the drum, insert a small tool through the hole in the rear of the backing plate, and hold the automatic adjusting lever away from the adjuster. Using another narrow, flat tool at the same time, reduce the brake shoe adjuster by turning the adjusting wheel.
If the drum is difficult to pull off using the bolts mentioned above, the parking brake is most likely the cause and will have to be adjusted "IN" to prevent drum to shoe contact.


ledsled378_171.jpg

Sep 20, 2011 | 2001 Suzuki Grand Vitara

1 Answer

I am working on a 2000 jeep wrangle sport. i cant get to my rear brakes because of a cover. how do i get that cover off so i can get to my rear brakes


That "cover" is the rear brake drum, part of the braking system. Jeep Sports come with drum rear brakes, not disc brakes. Once the lug nuts and tires are off, the drum will jut pull off. It may take some gentle force (hammer taps on the rear side) but there is nothing else securing it other than the rim and lug nuts.

Feb 18, 2011 | 2000 Jeep Wrangler

3 Answers

The rear drum wont come off as i would expect


Yes, Undo the 32mm nut, first. And, don't get the bearings dirty with dust from the brake drums, or , if you do, replace the inner and outer bearings with new greased up ones.prev.gif next.gif REAR DRUM BRAKES Brake Drums REMOVAL & INSTALLATION CAUTION
Brake linings contain asbestos. Asbestos is a known cancer-causing agent. When working on brakes, remember that the dust which accumulates on the brake parts and/or in the drum contains asbestos. Always wear a protective face covering, such as a painter's mask, when working on the brakes. NEVER blow the dust from the brakes or drum.
  1. Raise the vehicle and support safely.
  2. Remove the wheel and tire assembly.
  3. On vehicles without rear bearing hub, remove the dust cap, cotter pin, nut lock, wheel bearing nut and washer from the spindle. Remove the outer wheel bearing. Remove the drum with the inner wheel bearing from the spindle. If the drum is difficult to remove, remove the plug from the rear of the backing plate and push the self adjuster lever away from the star wheel. Rotate the star wheel to retract the shoes. Remove the grease seal.
  4. If equipped with a rear bearing hub, remove the drum by removing the retainer screws from the drum and pulling the drum from the hub assembly. If the drum is difficult to remove, remove the plug from the rear of the backing plate and push the self adjuster lever away from the star wheel. Rotate the star wheel to retract the shoes. To install:
  5. On vehicles equipped without rear bearing hub, lubricate and install the inner wheel bearing. Install a new grease seal. Install the drum to the spindle. Lubricate and install the outer wheel bearing, washer and nut. Adjust the bearing preload following the procedure outlined in the "Rear Wheel Bearing'' of this section. When the bearing preload is properly set, install the nut lock and a new cotter pin. Install the grease cap.
  6. On vehicles with rear bearing hub, install the brake drum to the hub assembly and install the retaining screws.
  7. Install the wheel and tire assembly. Adjust the rear brakes as required.
  8. Apply the brakes until a firm pedal is obtained, prior to moving the vehicle.

Jul 12, 2010 | 1991 Hyundai Excel 4 Door

3 Answers

Rear tire locked up


if your in a place to work on it remove back wheel and check the cable they rust when not used for long time pull the lever where the cable connects

Feb 10, 2010 | 1995 Chrysler LHS

1 Answer

1989 chevy 3500 4x4 454 rear brake drum removal. Does the axle bolts need to be removed


Can you tell me which type of axle you have?

Full Floating Axles To remove the drums from full floating rear axles, use the Axle Shaft Removal & Installation procedure in Section 7. Full floating rear axles can readily be identified by the bearing housing protruding through the center of the wheel.


Semi-Floating Axles
  1. Raise and support the rear end on jack stands.
  2. Remove the wheel.
  3. Pull the drum from the brake assembly. If the brake drums have been scored from worn linings, the brake adjuster must be backed off so that the brake shoes will retract from the drum. The adjuster can be backed off by inserting a brake adjusting tool through the access hole provided. In some cases the access hole is provided in the brake drum. A metal cover plate is over the hole. This may be removed by using a hammer and chisel.
314894f.gif
You may have to back off the automatic adjuster before you can pull the drum from the brake assembly

To install, reverse the removal procedure.

Dec 01, 2009 | 1989 Chevrolet C/K 3500

1 Answer

Trying to remove rear brake drum cover,have already adjusted star wheel and still won't remove. what am i doing wrong? for a 93 plymouth grand voyager


  1. Raise and support the rear of the vehicle on jackstands.
  2. Remove the wheels and tire assemblies.
  3. Remove the brake shoe adjusting slot cover from the rear of backing plate.
  4. Insert a thin tool through the adjusting slot and hold the adjusting lever away from the star wheel.
  5. Insert an adjusting tool and back off the star wheel by prying downward with the tool.
  6. Remove the center hub dust cover, nut, washer, brake drum, hub and wheel bearings.
To install:
  1. Inspect the brake lining and drum for wear.
  2. Inspect the wheel cylinder for leakage. Service as required.
  3. Remove, clean, inspect and repack the wheel bearings.
  4. Install the brake drum and tighten the hub nut to 20-25 ft. lbs. (27-34 Nm), then back off the nut until bearing pressure is released.
  5. Retighten the nut finger tight, align the cotter pin hole and install the cotter pin.
  6. Adjust the rear brakes as described in the beginning of this section.

36e0d00.gif
Removing the rear drum adjusting hole cover plug

Oct 07, 2009 | 1993 Plymouth Grand Voyager

1 Answer

1993 Toyota Paseo left rear wheel area souns like a gerbil running on a rusty tread mill? Could this be the wheel bearins and or bushings?


Remove the rear wheel & spin the brake drum. Listen for noise. Next, remove the wheel bearing cover/cap, and remove the drum & wheel bearing. Spin the hub, listen for noise. You either have rust buildup on the interior of the brake drum or bad wheel bearings.

Aug 02, 2008 | 1997 Toyota Paseo

2 Answers

REAR BRAKES


i think your aware of how to change the brakes if im right and your problem is the rusted drum doesnt want to come off the only way to get the old drum off is to remove adjuster plug from behind drum dustshield and adjust the shoes so that there not even close to the braking area of the drum then try and wiggle the drum off of the assembly if it is not coming off then you need to use the old nylon hammer on the drum and i mean you must hit the drum from side to side trying by hand to wiggle the drum off its a tight fit and you need to strike the drum on the face not on the fins not wanting to damage with persistance and care and patience you will eventually be able to remove the drum to service brakes take care and good luck with it

Jul 01, 2008 | 2007 Dodge Caliber SXT Sport Hatchback

Not finding what you are looking for?
2005 Chrysler Town & Country Logo

262 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...