Question about 1993 Chevrolet S-10 Blazer

Open Question

How to install an s-10 blazer 4.3 litre v-6 motor

How to install an s-10 blazer 4.3 litre v-6 motor mount

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 02 blazer i want to put a motor out of a 98 in it will it interchange


Chevy Blazer Engine Swap Part 1 of 2 - YouTube

? 10:29
https://www.youtube.com/watch?v=Dt_7AKP2WcI
Aug 13, 2011 - Uploaded by Dave R
Replacing the engine in a mid-size Chevy Blazer 4x4 with oneout of a Jeep Cherokee 2wd. Original engine was low and motoroil and spun a bearing. ... Chevy Blazer Intake Gaskets Replaced & Cooling System Rebuilt - Duration: 16:45. by ... 4:02. 94 4.3l Vortec V6 GM (black motor) - Duration: 6:01. by ...

4.3 vortec engine removal - YouTube




Jan 01, 2016 | Cars & Trucks

1 Answer

What would it cost a mechanic to install motor mounts on a 1995 gmc sonoma 4.3 litre 4*4


Im sure your 95 is no different then my 01 sonoma 4x4 u shouldn't need a cherry picker to do the engine mounts a small block of wood and a floor jack to support the engine from underneath and take a little bit of the load off the mount should work you dont have to lift the engine out to do them its not easy this way but is possible and cost less money working for a gm parts department and a former tech you would be spending and average of 75 to 100 an hour labor wise depending on what shop u take it to and what shop labor rates at like near you I would estimate an easy 2 hours labor but it all goes by book time thats or determined at the shops

Mar 27, 2014 | 1995 GMC Sonoma

1 Answer

Location of egr valve on 2003 chevy silverado


Hi there:
Here is a picture showing the EGR valve on the 4.8 Litre V8. The numbers below go with the picture. The arrow points to the front of the truck.

(1) Fuel Injector 2 Connector
(2) Throttle Actuator Control (TAC) Motor Connector
(3) Throttle Actuator Control (TAC) Motor
(4) Exhaust Gas Recirculation (EGR) Valve Connector
(5) Exhaust Gas Recirculation (EGR) Valve
(6) Fuel Injector 6
(7) Ignition Coil 2


9_14_2012_3_34_36_am.jpg
Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Sep 14, 2012 | 1989 Chevrolet Camaro

1 Answer

How to change oil pan on 1990 blazer 4x4 4.3 litre engine. remove motor??


You dont need to remove the motor. Just go underneath the car and take the blots off and see if there is any thing that blocks it from sliding out and take it off and then take the old gasket off and put new one in and dont forget to use some sealant too. Good luck

Dec 09, 2010 | 1989 Chevrolet S-10 Blazer

1 Answer

What size our the speakers in the back doors


Car speaker fit guide - CHEVROLET BLAZER S-10 2001
According to our database, here are the speakers types that go in your CHEVROLET BLAZER S-10 2001 car, along with their location:
  • Front: 4" x 6", 6-3/4"
  • Rear: 6-3/4", 6" x 9"
  • Dash: 4" x 6"
  • Front door: 6-3/4"
  • Back door: 6-3/4"
  • Rear side panel: 6" x 9"

Oct 04, 2010 | 2001 Chevrolet Blazer

3 Answers

What other engines can be used in a 84 S-10 blazer besides the 2.8 V6?


A 4.3 V-6 will fit, going to a V-8 tyou may have to change out tranny and all mounts

Jan 26, 2010 | 1984 Chevrolet S-10

1 Answer

Removed & replaced dist. cap and rotor on 1993 S10 Blazer 4.3 V-6


The firing order for a Chevy s10 depends on which engine you have. 1.9L engine the firing order is: 1-3-4-2 . Distributor rotates counterclockwise. 2.0L engine the firing order is: 1-3-4-2 . Distributor rotates clockwise. 2.5L engine the firing order is: 1-3-4-2 . Distributor rotates clockwise. 2.8L engine the firing order is: 1-2-3-4-5-6 . Distributor rotates clockwise. 4.3L engine the firing order is: 1-6-5-4-3-2 . Distributor rotates clockwise.

Jul 03, 2009 | 1993 Chevrolet S-10 Blazer

2 Answers

Need firing order for 96 trail blazer 4.3


  Firing order 1-6-5-4-3-2 ------------ | 2 4 6 | front | | | ------- | | | 6 5 || of | | 1 4 || | | 2 3 || | ------- | vehicle | | | 1 3 5 | ------------ Distributor rotates clockwise

Mar 07, 2009 | 1994 Chevrolet S-10 Blazer

1 Answer

1984 s10 2.8 manual trans. flywheel causes engine to vibrate


no should be same engine. check your engine mounts and tranny mount. how bad a vibration? sometimes after installing engine the trans gets shifted around and if mount was worn it will allow it to hit crossmeber and vibrate.

Jan 16, 2009 | 1984 Chevrolet S-10

Not finding what you are looking for?
1993 Chevrolet S-10 Blazer Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...