Question about 1987 Ford Thunderbird

1 Answer

Same check engine "beep" sound but check engine lights not on. I did the trip reset - wait for three beeps, but this has not solved this issue. All of my guages check out ok. When the "beep" (fairly loud sound) happens, the car does not slow down, stop or otherwise behave as if anything is wrong.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Pull positive off the batt. for like a min or two and see if that helps

Posted on Jul 31, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Has anyone had a VW EOS having an issue with three beeps and no indication on the dash.


OBVIOUSLY MR MCDONALD...I WOULD RECOMEND TO ASK THE DEALER TO CHECK FOR ANY UPDATES AT THE BCM ENGINE ECU AND ABS ECU ALSO..

Feb 22, 2015 | 2012 Volkswagen Eos

1 Answer

How to stop beeping


Sound sleek you have two problems. Check your brake fluid level immediately for the beeping and brake light on!
The check engine light is a completely different story.
I recommend you take it to a shop.

Aug 23, 2014 | 1998 Mercedes-Benz C-Class

2 Answers

Why the light about change oil is blinking in the meter


U have 2 take it back 2 whomever changed the oil so the warning light can b reset!

Aug 05, 2014 | 2006 Hummer H3

1 Answer

How to get change oil light to go off


Instructions:1) Check the oil. The light is a warning signal that you are low on oil or that the oil is not flowing properly. If the oil level is fine then the issue may be a reset button. Two different methods will allow you to reset the oil light.2) Turn the key to the on position. Do not turn the engine on. Press the accelerator pedal down three times in a five-second period. Turn the engine on. If the oil light goes off you have successfully reset the oil light. If it stays on you need to try the second method.3) Find the fuse box. This should be under the dash in between the steering wheel and the door. Open the fuse box and look for the reset button. Press the button until you hearing a beeping sound. It will beep three times. The oil light should be reset. Turn the engine and see if the oil light goes off. If the oil light stays it still has not been successfully reset.
4) Read the manual. The two methods above are the two most common ways of resetting the oil light. Your car may have additional options to try. If none of the methods resets the oil light then there is a different problem such as a non-functioning oil sensor. At this point you need to see a mechanic.

Parts Of BMW.


May 30, 2012 | 2005 Dodge Magnum

2 Answers

I need to reset the oil change light.how do I do This?


1. Engine off, turn ignition key to RUN - do not start engine - make sure dashboard indicator lights come on

2. Put foot top of accelerator

3. Completely depress and release the accelerator TO THE FLOOR, THREE TIMES in rapid succession, within FIVE SECONDS - press release, press release, press release. Then wait a few seconds and the CHANGE OIL light should usually flash, sometimes accompanied by a few short beeps. Once it flashes it should disappear, and it should be reset.

Dec 22, 2010 | 2003 Pontiac Grand Am

1 Answer

Engine service required message


If you want to reset the light/message:

Close all the doors, booth, hood etc. hatches,

1. Make sure you have Trip odometer 1 (T1) selected.
2. Turn the ignition key to 'I'-position.
3. Press the trip odometer reset - keep it down.
4. Turn the key to 'II'.
5. Wait till the service light blinks a few times or you hear a 'beep'.
6.Release the trip odometer reset.
7. Turn the key back to '0' - service light is reset.

If this doesn't work, try:
a) 2. before 3. then continue as above
b) 5. Wait until the previous mileage appears again to the trip odometer.
c) 7. before 6.

You can reset the service counter at any time. Do not forget to service your car!

Jun 06, 2010 | 2002 Volvo S60

2 Answers

LEXUS LS 2004 Maint Reqd (Master warning light) how I can switch off after change the oil engine?


You can disconnect your battery for 15 minutes or pull the fuse for an ECM or PCM fuse, but the best way is to visit any local repair shop. Most shops will have a universal Check Engine Light Code Reader that can quickly and safely reset check engine light trouble codes. It should take about 30 seconds.

Ask your local service center if they could reset the check engine light with a Check Engine Light Code Reader.

Dec 14, 2009 | 2004 Lexus LS 430

1 Answer

I get three beeps, car dies toally.


have you checked your ground wires under your battery? also possible that your alternator is not putting out enough. check ground cable from battery to alternator. see if that is warm as well if your larger cables have corrosion built up in them this will cause your concern as well. does your immobilizer little key and car light flash at you?do you have a remote key does it flip partially closed when you start the car? that could cause it to think it is being stolen.

Sep 08, 2009 | 2003 Volkswagen Jetta TDI

2 Answers

After flat tire, tire pressure warning will not go out even after making sure pressure is at 44psi. How do I reset dash?


44PSI?? is that what your car recommends...


1. check and make sure that your tires are inflated to the correct pressure

2. turn the ignition switch to the ON position. If the low tire pressure warning light comes on, push and hold the tire pressure warning reset switch (think the switch is in the glovebox, but not sure) until the warning light turns off and then release the switch.

3. now press and hold the tire pressure warning reset switch until the low tire pressure warning light blinks three times.

Aug 14, 2009 | 2006 Hummer H3

1 Answer

Three beep alarm means what?


What lights are on on the dash, I'd check your fluids (coolant especially) .

Jun 30, 2009 | 1998 Volkswagen Beetle

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...