Question about 2000 Mitsubishi Galant

1 Answer

How to install driver side window regulator - 2000 Mitsubishi Galant

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 73 Answers

1. Take door panel off by prying off with srew driver moldings for outside mirror,around lock,and door handle, then pry up counsel for power locks, windows, and mirror adjustment and disconnect plugs. Remove three screws located behind arm rest handle, inside where counsel was removed, and bottom middle of door panel. Lift panel and pull slighlty towards you. Disconnect courtesy light, and wire to speaker. This may sound like alot but it goes pretty fast. 2. Peel away plastic and loosen window glass clamps (explaination from above, which are accessable when window is in up position). 3. Disconnect wire to motor, and remove 6 bolts holding guide rails and motor. Lift rails slightly to release from little hangers, which come in handy when putting new one in. 4. You should be able to remove entire window regulator at this point. Surprisingly the window stayed in up position when regulator was removed. 5. Before installing new regulator loosen window glass clamps. Install new by first setting guides in place by using the little hangers. Bolt guides and motor, temporarily connect power window switch and carefully raise window regulator until clamps are resting in place under window glass, tighten clamps. Test before putting panel back on.

Posted on Jul 30, 2009

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
MrScary66613
  • 1990 Answers

SOURCE: 2002 buick lesabre driver side regulator motor removal

You will need to Drill out the Rivets that Hold them Right Now and Use Screws to Reinstall.

Posted on Jan 22, 2009

  • 78 Answers

SOURCE: How do you install a window regulator for a 2001 dodge dakota?

well first take off the door panel it shouldnt be hard remove plastic cover off door.Make sure your window is all the ways up before you remove the motor.you can hold it up with duct tape or anything similar.Then remove the screw that go to the regulator sometimes it has rivets wich have to be drilled off.The new regulator should come with screws if it has rivets if not u use the same old screws.Also unplug the harness of it . Install new one,screw it on and reverse the procedure.Any problems keep me posted

Posted on May 23, 2009

  • 166 Answers

SOURCE: Broken drivers side window regulator on my 95 SC400

i do theses regulators all the time . its not hard to change the motor . you may need to drill out the rivits and replace them with bolts and nuts

Posted on Jun 10, 2009

  • 265 Answers

SOURCE: Replacement of front driver side window regulator

maybe it is like a maxima...

http://www.a1electric.com/maximareg.htm

Posted on Jul 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On my 2001chevy blazer the driver side window won't go down how do I fix it


REMOVAL PROCEDURE:
Remove the window.
  • Disconnect the power window motor electrical connector, if equipped.
  • Remove the electrical harness retainers, if equipped.
  • Drill out the rivets that secure the window regulator to the door.
  • Remove the window regulator from the door.
  • Remove the power window motor, if equipped.

INSTALLATION PROCEDURE:
  • Install the power window motor, if equipped.
  • Install the window regulator to the door.
  • Install the rivets that secure the window regulator to the door using J 34940.
  • Connect the electrical connector, if equipped.
  • Connect the electrical harness retainers, if equipped.
  • Install the window.

Jul 18, 2013 | Cars & Trucks

1 Answer

How hard will it be to replace the window motor, driver side, of a 2002 Chevy blazer? Do I need special tools to do the job?


Motor Replacement - Power Window

Removal Procedure
Be very careful
Hope this helps




Caution: Do not attempt to service the regulator motor withoutreleasing the counterbalance spring tension. The regulator lift arm isunder tension from the counterbalance spring and can cause personalinjury if the motor is removed from the regulator.

  1. Remove the window regulator.
117423422
  1. Drill a hole through the window regulator and the sector gear.
117423423
  1. Install a bolt and a nut through the hole in order to lock the sector gear in position.
  2. Drill out the rivets that secure the power window motor to the window regulator.
  3. Remove the power window motor from the window regulator.
Installation Procedure
  1. Install the power window motor to the window regulator.
117423423

Important: Remove the nut and the bolt that were used in order to secure the sector gear in position.

  1. Install the rivets in order to secure the power window motor to the window regulator.
  2. Install the window regulator.

Jan 01, 2011 | 2002 Chevrolet Blazer

1 Answer

My passenger side driver power window will not roll up or down. whats wrong with it. my drive side window works fine


get a new power window regulator on ebay. pay a glass shop to install it. the driver side regulator will fail eventually too.

Oct 26, 2010 | Chevrolet Astro Cars & Trucks

1 Answer

On my 2002 vw cabrio, the drivers side front power window works intermittently - mostly won't work. Passenger side is fone as are the rear power windows. Is this a switch problem?


The most common problem with Cabrio auto windows is the Window regulator. Each window has it's own. My wife also owns a 2002 Cabrio, that had a mis-behaving window driver window and the passenger was locked in the up position. After inspecting the drivers window, I found one of the cable roller guides was broken, causing the cable to snag when using the window open / close, and resulting in the window seeming to have a mind of it's own. I had a local garage order the regulator for me, and then I disassembled the drivers door and installed the new regulator (problem is now solved).
The passenger window was bound up, I also had to remove the regulator and let loose the tension in the cable system by carefully removing the cover over the cable roller. This window works fine now as well.

Jun 13, 2010 | 2002 Volkswagen Cabrio

1 Answer

How do I replace my window regulator?


You will have to remove the driver side door panel. Tape the top of your glass to the door so it wont fall and break. Remove the bolts and harness' going to the regulator. And reverse for installation.

Apr 01, 2010 | 2003 Chevrolet Venture Passanger

1 Answer

I need instructions on how to replace power window motor for the front driver side window of a 2002 Grand Cherokee


Power Window Motor: Service and Repair
REMOVAL
1. Disconnect and isolate the battery negative cable.
2. Remove the window regulator from the door.
3. Place the window regulator on a suitable work surface and remove the screws that secure the power window motor to the window regulator.
4. Remove the power window motor from the window regulator.
INSTALLATION
1. Position the power window motor onto the window regulator.
2. Install and tighten the screws that secure the power window motor to the window regulator. Tighten the screws to 9 Nm (80 in. lbs.).
3. Install the window regulator onto the door.
4. Reconnect the battery negative cable.

Oct 30, 2009 | 2002 Jeep Grand Cherokee

1 Answer

Fallen driver's side window


probably need a new window regulator. ebay. 93 to 98 should fit.

Section 01-05: Trim, Interior 1998 Villager Workshop Manual
REMOVAL AND INSTALLATION Trim Panel(s), Door Front
Removal
  1. Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
  1. swv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
    Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942) .




  1. If equipped with manual windows, slip a clean shop rag between the window regulator handle (23342) and the front door trim panel .
  1. Pull the shop rag back and forth to release the window regulator handle clip.




  1. Remove the three cover caps and front door trim panel screws.
  1. Remove the one front door trim panel capped screws from the door pull handle.
  1. If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
  1. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124) .
  1. Remove the front door trim panel.
Installation
To install, reverse the removal procedure.
---------------------------------------------------------
Window Regulator, Power Front Door
Removal
  1. Disconnect the battery ground cable (14301) .
  1. Remove the front door window glass (21410) . Refer to the front door window glass removal procedure in this section.
  1. Remove the two front door brace bolts and the front door brace.


    415712f.gif

  1. Disconnect the front window regulator electric drive electrical connector.
  1. Remove the four front door window glass regulator track bolts.

    67b6136.gif


  1. Remove the three front window regulator electric drive bolts.
  1. Remove the front door window glass regulator track and the front window regulator electric drive (23394) as an assembly through the opening in the front door (20124) .
Installation
  1. Install the front door window glass regulator track and the front window regulator electric drive as an assembly through the opening in the front door .
  1. Install the three front window regulator electric drive bolts. Tighten the front window regulator electric drive bolts securely.
  1. Install the four front door window glass regulator track bolts. Tighten the front door window glass regulator track bolts securely.

Apr 29, 2009 | 1998 Mercury Villager

1 Answer

Driver's side window


You will need to pull the door panel and then the window regulator inside the door, the glass will be riveted or glued into the metal channel mounted on the top of the window regulator, most late models are riveted. Be careful to install in same position as removed.

Jul 28, 2008 | 1996 GMC Jimmy

2 Answers

Driver side window


the regulator is broken cable broken no part availleble you need to change window regulator hope this help you fixya our post thanks pierre

Jul 12, 2008 | 2004 Honda Accord

3 Answers

Power window doesn't work on drivers side only 2003 galant es. driver's side power window not working. window is totally down and not coming up.


I had the same problem with the driver's side front and rear windows. Had to replace the motor assemblies.

Jul 02, 2008 | 2003 Mitsubishi Galant

Not finding what you are looking for?
2000 Mitsubishi Galant Logo

2,291 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...