Question about 2000 Chrysler Grand Voyager
You have to drop the gas tank out from under the vehicle. You must first drain as much gas out of the tank as you can. Then support the tank with a jack. Preferably with a large plate. Then remove the retaining straps. If you can remove any of the fuel lines and fill nozzle before lowering please do. If you cannot, lower the tank until access to wiring harness and fuel line disconnects can be made. With a special fuel line tool remove lines and harness and anything else that may hinder the removal on the tank. Once the tank is out from under the vehicle remove as much dust and debris as you can fom the top of the unit. Remove the retaining ring using a hammer and a punch, or screwdriver. Once the retaining ring has been removed carefully remove the fuel pump assembly from the tank. be careful not to damage the float. replace pump in the reverse order above.
Posted on Sep 03, 2009
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: blower resistor
In the manual I have it is shown to be located under the hood at the rear of the compartment on the firewall area where there are several rectangular openings. The block is hidden from view below the wiper module on the lower edge of one of those openings. It has a 5 wire plug on the cabin side of the the opening. If you don't find it, then I know in the 2001 model it was in the cabin, behind the glove box again with the resistors sticking thru the firewall where the air intake would cool them. I just don't know in what year the block was moved between '98 and '01
If you find it in the first location you use a couple of flat blade screwdrivers to release the block and pull it into the engine compartment. On the hidden side push on a spring tang on the driver's side narrow edge of the block and on the comparment side you will see a couple of etched lines on that same side showing where to put the tip of the other screwdriver to pry it forward into the compartment.
Get a replacement block and install making sure the resistors aren't touching one another. If you have trouble removing it I can send you a page that shows what I described above. PS Please let me know where you find the resistor block to be located. Use the 'thank and rate' tab to get back to me quickly without having to wait for me to be "available"
Posted on Apr 13, 2009
use a lift, let van cool or change front three while van is cooling and from the under side of the engine change the other last three. They can be reached easily. No need to remove plenium.
Posted on Jul 08, 2009
The clock spring is located under the steering wheel, the airbag must be disarmed (if not done correctly can can serious injury) and the steering wheel removed to replace it, a dealer will charge about $200 for this repair.
Posted on May 15, 2009
Dear Waterpump Fitter,
These voyagers are actually fairly easy to install the waterpumps on, The pump is located on the passenger side of the vehicle closer to the front (towards the bumper) It should take the first or second timer maybe a couple of hours to install.Please et back to me if you have any other questions..I'M HERE TO HELP!!
Posted on Nov 20, 2009
Tips for a great answer:
Oct 26, 2013 | 2000 Chrysler Grand Voyager
Sep 30, 2013 | Cars & Trucks
Jan 28, 2013 | 2000 Chrysler Grand Voyager
Sep 29, 2012 | 2000 Chrysler Grand Voyager
Jun 12, 2010 | 2000 Chrysler Grand Voyager
Apr 17, 2010 | 2000 Chrysler Grand Voyager
Jan 17, 2010 | 2000 Chrysler Grand Voyager
Dec 06, 2009 | 2000 Chrysler Grand Voyager
Jul 11, 2009 | 2000 Chrysler Grand Voyager
919 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: