HI I WANT TO KNOW THE TORQUE SETTING ON NISSAN NAVARA 4X4 2010 MODEL FRONT WHEEL HUB ASSEMBLY

Once you get the words in the right order to form the search query, you need to add the word of the part you want the torque setting for. The problem is the all the weighting is given to the torque that the engine produces and is normally right next to the horsepower

https://www.google.com/search?q=2017+Nissan+Navara%2C+2.3+turbo+diesel%2C+Torque+Settings

So insert 'wheel nuts', 'cylinder head' etc HERE

2017 Nissan Navara, 2.3 turbo diesel, HERE Torque Settings

Example for 'cylinder head'......

https://www.google.com/search?q=2017+Nissan+Navara%2C+2.3+turbo+diesel%2C+cylinder+head+Torque+Settings

..

It is unlikely someone will simply reply with where to find those diagrams online. Here is a post somwhere else online I found that may help "Chilton's and Haynes both make books for your truck. There is no factory service manual available unless you find a paper copy on Ebay" Also you can also check out your local library for those books. Some have them some dont. good luck.

The one that fits!

That's not the way it works. you buy a socket set. It has one set of AF Sockets and one set of Metric sockets. The one you use is the one that fits.

Hub and Wheel Bearing Torque Specifications - DRiV

drivcat.com > HubWheelTorqueTableWindow

2009 Ford Fusion ... Front Proc 1 Note ... Front Proc 2 Note ... Do not attempt to tighten the nut with the vehicle on the ground or the wheel bearing will be ...

Front Axle Nut Torque Spec - Lounge - Fusion Energi - Ford ...

www.fordfusionenergiforum.com > topic > 6160-front-...

Dec. 2, 2019 - Im replacing the front wheel bearing assemble this weekend and cant find the torque spec for the ale nut. The older model Fusion (up to 2012) ...

BHA54317 Axle / Spindle Nut Torque Specification - 1A Auto

docs.1aauto.com > BHA54317 Torque Spec

PDF Vehicle Notes. Lb. ft NM. Ford. Fusion. 2006-12 (Excluding All Wheel Drive Models). Rear. Lincoln. MKZ. 2007-12 (Excluding All Wheel Drive Models). Rear.

SKF-Front-Rear-Axle-Nut-Hub-Mount-Lug-Nut-Torque-Spec

dannysengineportal.com > wp-content > uploads > S...
PDF
Front & rear axle nut, hub mount and lug nut torque specifications for FWD ... 3 Series AWD E92, E93 ....2012-2013 . ... FORD / MERCURY TRUCKS - cont.


..

there are 2 sets of torque specs for flywheel bolts as there are 2 different fly wheels in use with different bolts for each
go google and type in--torque specifications for nissan navara flywheel bolts and fins a site relevant to you application
it could be 61-69 ft/lbs a or 90 ft lbs depending on the flywheel and the vehicle 2wd or 4wd

Three bolts are 70 lbs,could be 120+/-.

For the hub assembly? Or the wheel nuts?

TO REMOVE FRONT WHEEL BEARING.YOU NEED TO SAFELY RAISE SUPPORT VECHICLE ON JACK STANDS.MAKE SURE SITTING ON LEVEL SOLID GROUND.BEFORE RAISING VECHICLE OFF GROUND YOU NEED TO LOOSEN HALF SHAFT AXLE NUT JUST A LITTLE BECAUSE WHEEL IN THE AIR HARD TO LOOSEN AXLE NUT WHEN YOU HAVE HOLD THE WHEEL WHILE LOOSEN THE AXLE NUT WHICH IS TORQUE ON ABOUT 200 FT LBS.USING A SIX POINT AXLE SOCKET SOCKET SIZE COULD BE 34 OR 35 METRIC 1/2 INCH SOCKET.YOU NEED 1/2 INCH BREAKER BAR.ONCE YOU LOOSEN AXLE NUT A LITTLE THEN RAISE VECHICLE THEN REMOVE WHEEL.THEN FINISHING REMOVING AXLE NUT AND WASHER.THEN REMOVE THE CALIPER FROM THE STEERING KNUCKLE AND SUPPORT IT ASIDE USING A PIECE OF WIRE.REMOVE BRAKE ROTOR.THEN REMOVE THE 3 HUB BEARING ASSEMBLY BOLTS. USE A SWIVEL SOCKET GOING TO BE HARD TO REACH SPOT WITH A REGULAR SOCKET. REMOVE THE HALF SHAFT FROM THE HUB BEARING ASSEMBLY.REMOVE HUB AND BEARING ASSEMBLY. PUT EVERY THING BACK VISA VERSA. TORQUE HUB BEARING BOLTS TO 70 FT LBS. TORQUE AXLE NUT 284 FT LBS IF YOUR CAR IS 1998 MODEL AND TORQUE AXLE NUT 100 FT LBS FOR THE 1999 TO 2001 MODELS.THE WHEEL HAS TO BE ON THE GROUND JUST ENOUGH TO KEEP IT FROM TURNING.DONT LET ALL THE CAR WEIGHT DOWN UNTIL YOU HAVE TORQUE WHEEL TO THE RIGHT TORQUE.LET ME KNOW IF YOU HAVE ANY PROBLEMS.

Removal & Installation Front To Remove:
The front wheel bearings are not serviced separately. If the front wheel bearings are defective, the hub and bearing assembly must be replaced.

1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
2. Lubricate the threads on the halfshaft with clean engine oil.
3. Remove or disconnect the following:
   • Front wheels
   • Halfshaft hub nut
   • Caliper from the steering knuckle WARNING
     DO NOT allow the brake hose to support the weight of the caliper.
     
   • Brake rotor
   • Anti-lock Brake System (ABS) sensor from the backing plate
   • Hub and bearing assembly from the backing plate
   • Hub and bearing assembly from the halfshaft
   • Hub and bearing assembly

To Install:
Exploded view of the front hub mounting and related components

1. Install or connect the following:
   • Hub and bearing assembly onto the halfshaft
   • Hub and bearing assembly to the backing plate. Torque the 3 bolts alternately and evenly to 70 ft. lbs. (95 Nm).
   • ABS sensor
   • Brake rotor
   • Caliper on the steering knuckle.
   • Halfshaft nut. Torque it to 118 ft. lbs. (160 Nm).
   • Front wheel. Torque the nuts to 100 ft. lbs. (140 Nm).

Front (4 Wheel Drive) To Remove:

1. Raise and support the vehicle
2. Remove or disconnect the following:
   • Tire and wheel assembly
   • Rotor (See: Disc Brake Rotor)
   • Wheel speed sensor and brake hose mounting bracket bolt from the steering knuckle
   • Electrical connection for the wheel speed sensor
   • Front drive halfshaft assembly (See: Halfshaft)
   • Hub and bearing assembly mounting bolts 4WD front hub
     
     
   • Hub and bearing assembly

To Install:

1. Clean all corrosion or contaminates from the steering knuckle bore and the hub and bearing assembly
2. Lubricate the steering knuckle bore with wheel bearing grease or the equivalent
3. Install or connect the following:
   • Hub and bearing assembly
   • Hub and bearing assembly mounting bolts and tighten the hub to knuckle bolts; Torque to: 133 ft. lbs. (180 Nm)
   • Front drive halfshaft assembly (See: Halfshaft)
   • Electrical connection for the wheel speed sensor
   • Wheel speed sensor and brake hose mounting bracket bolt to the steering knuckle and tighten the bolt; Torque to: 106 inch. lbs. (12 Nm)
   • Rotor (See: Disc Brake Rotor
   • Tire and wheel assembly
   Wheel lug nut tightening sequence
   
   
4. Torque the lug nuts to specification
5. Test drive the vehicle to confirm the repairs

replace the bearing or wheel hub assembly.

REMOVAL & INSTALLATION 2wd Models NOTE: Refer to wheel bearing service and bearing preload adjustment procedures found in Section 1.

1. Raise the front of the truck and support it with safety stands. Remove the wheels.
2. Remove the brake caliper and suspend it with wire, out of the way. Remove the caliper torque plate if equipped.
3. Remove the dust cap and then remove the cotter pin, lock washer (if equipped) nut lock and nut.
4. Pull the hub/disc assembly off the spindle with the outer bearing. Don't let the bearing fall out.
5. Pry the inner oil seal out and remove the inner bearing. To install:
   
6. Clean and inspect the bearings and outer races.
7. Using a brass drift and a hammer, drive out the bearing outer race. Press a new one into position.
8. Pack the bearings with grease until it oozes out the other side. Coat the inside of the hub and cap with grease.
9. Position the inner bearing into the hub, coat the oil seal with grease and press it into the hub.
10. Press the hub assembly onto the spindle and install the outer bearing and thrust washer.
11. Install the hub nut. Turn the hub a few times to seat the bearings and then loosen the nut until there is 0mm axial play. Using a spring tension gauge, check that the preload (with new grease seal installed) is 2.2–6.4 lbs. (9.8–28.4N)
12. Install the lock-nut, new cotter pin and hub grease cap.
13. Install the brake torque plate. Install the brake caliper.
14. Install the wheels and lower the truck.

4wd Models The hub and bearing service procedures for a 4wd models are basically the same as those for a 2wd version, with the exception of removing the free running hub assembly and the bearing preload adjustment. Refer to Sections 1 and 7 for additional information. Adjust the preload after the wheel bearing is replaced or the front axle assembly is reassembled. BEARING PRELOAD ADJUSTMENT

1. Thoroughly clean all parts and pack the wheel bearings.
2. Apply grease to threaded portions of the spindle, grease seal lip and wheel hub.
3. Tighten the wheel bearing lock-nut with a socket and torque wrench to 58–72 ft. lbs. (78–98 Nm).
4. Rotate the hub in both directions a few times to seat the bearings. Loosen wheel bearing lock-nut.
5. Retighten the lock-nut to 0.4–1.1 ft. lbs. (0.5–1.5 Nm).
6. Turn wheel hub several times in both directions.
7. Retighten the lock-nut to 0.4–1.1 ft. lbs. (0.5–1.5 Nm). Fig. 1: Exploded view of the front axle assembly — 2wd models
   Fig. 2: Removing the bearing outer races
   Fig. 3: Packing the wheel bearing with grease
   Fig. 4: Pack the lip cavity of grease seal with grease
   Fig. 5: Exploded view of the front axle assembly — 4wd models
   
   
8. Measure wheel bearing axial end-play. The wheel bearing end-play specification is 0.
9. Install lock washer by tightening the lock-nut within 15–30 degrees.
10. Turn wheel hub several times in both directions. Wheel bearing should be seated correctly.
11. If necessary, measure wheel bearing preload. NOTE: Measure wheel bearing preload with a spring-type gauge; measure at wheel hub bolt, with tire removed. The hub assembly should rotate with 1.6–4.7 lbs. (0.73–2.13 kg) of pressure.