Question about 2000 Ford Windstar

1 Answer

# 10 fuse keeps burning out immediately


As soon as i start it, it burns out again.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,187 Answers

There may be a short circuit leading from the fuse. Have the wires traced for corrosion or cuts on the wires and the terminals.

Posted on Jul 30, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2005 Nissan Maxima. Gauges don't work. Brake lights won't work. The fuses all work. The one for brake light keeps burning out soon as it's put in.


Disconnect the connector from the brake light switch at the pedal. Put in a fresh fuse. If it burns, you have a short in the red wire that runs from the fuse to the brake light. If it doesn't burn, replace the switch.

0996b43f802588c0-lxsvs4ftyjtcqsaualeaxmu4-4-0.gif

Aug 25, 2017 | Nissan Cars & Trucks

1 Answer

What could be causing the front axillary fuse to keep blowing? Even bigger fuses blow.


fuses blow from over current( dead short) they are rated at lower than what is required so that the wire doesn't burn
If you keep putting in bigger fuses without fixing the dead short, eventually the wire will melt the plastic insulation off and the vehicle will burn

Apr 29, 2016 | 2005 Buick Rendezvous

1 Answer

Why is my 2003 land rover Freelander burning 20amp fuel system fuses


You have an electrical short in that circuit. The fuse is doing its job, preventing a fire (barely). You need to find where the short is before trying to operate this vehicle again, or you will end up setting it on fire. Look for the burned/melted wires.

Feb 14, 2016 | 2003 Land Rover Freelander

1 Answer

Turn signal fuse burns out as soon as i install new fuse


then you need to look for the short /BARE wire someplace. we can find it from here

Sep 26, 2015 | 1995 Buick Century

1 Answer

Volvo V70 fuse in slot 7 Radio/Amplifier keeps blowing when trying insert new fuse


red is hot and black is ground never switch the two around , put them back the way they where and if your battery is going dead because of to much voltage drawn then you need to up the battery size and alternator .

Feb 15, 2013 | 2000 Volvo V70

1 Answer

I have a 1991 gmc sonoma 4.3 i replaced the fuel pump thinking it was bad. the new one didnt turn on either so i checked the fuse and it was burn out.put a new fuse and the truck started right up but when...


Most likely the positive power wire is grounding out. start at the fuel pump and fallow the wire back to the fuse box also check the connector at the fuel pump for corrosion. also check you're fuel pump relay.

Nov 07, 2017 | Cars & Trucks

1 Answer

I ran out of gas in a 1997 Chevy Blazer, put gas in, but still won't start.


The fuel filter may be to dirty to let the gas flow through and will need to be replaced, or most common when you run out of gas is the fuel pump will burn it self out. The fuel in the tank will keep the fuel pump cooled and will keep it from burning out, if you ran it out of gas. The pump may have burn out and will need to be replaced. Check the fuse first and hope the fuse blown due to the extra amp drown from the pump running without fuel. If the fuse is good, then check to see if you can hear the fuel pump start up when you turn the ignition key to the run position. Note the fuel pump will only energize the fuel line for 5 seconds, so you need to listen for the pump to turn on right away. The other thing too, is you can check the fuel pressure at the shredder valve, there should be 62 to 65 PSI when energizing the fuel line and will drop around 5 PSI when the engine is running. Make sure you do not try to start the engine by pouring gas down the throttle body, it been know for the gas to catch fire in the intake manifold and burn up the fuel injector system which is very costly. Start with the simple and check the fuses and fuel pump, then replace the fuel filter. At worst, your going to have to replace the fuel pump by dropping the gas tank and don't forget to replace the wire harness from the fuel pump to the frame. Good luck and hope this helps, keep me posted. Be glad to know you got your Blazer running again soon.

Dec 09, 2009 | 1997 Chevrolet Blazer

2 Answers

Air coditioning fan


u have electrical problem with ur AC Fan connection

Aug 02, 2008 | 1995 Honda Accord

Not finding what you are looking for?
2000 Ford Windstar Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

78936 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

fordexpert

Level 3 Expert

5676 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...